EverFocus ED350 Manual de usuario
EVERFOCUS
1/3” 560 TVL Color Mini Dome Camera
Operation Instructions
Model No. ED350
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.
2. Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.
3. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
4. Keep the power cord away from water and liquid.
Touching the wet power cord may result in electric shock.
5. Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in failure, electric shock or fire.
6. Cleaning
Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from
the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the
camera lens.
1
7. Do not operate the camera beyond the specified temperature, humidity or
power source ratings.
Use the camera at temperatures within 0℃~ 40℃(32℉ to 104℉) and humidity between
20%~ 80%. The input power source is 12VDC/24VAC.
PREFACE
The ED Series are compact, full functioned CCD Color Indoor Dome Cameras. The stylish
appearance can be applied as per installer's ideal locations on the ceiling. The dome camera
designed with advanced digital processing circuitry for high resolution 1/3" color interline transfer
CCD sensor, it has DIP switch for AGC on/off, BLC on/off. ED vari-focal models use vari focal
auto iris lens for discreet surveillance or close-up viewing and it features with iris LEVEL volume
control for the best viewing quality. ED300 is 520TVL dome camera equipped with simple Day
and Night feature. ED350 is 560TVL high resolution. ED230/330 is day and night IR Dome
camera.
FEATURES
z1/3” Sony super HAD CCD image sensor with approximately 410,000 pixels.
z560 TVL of horizontal resolution.
zRevolutionary integrated 10-bit Digital Signal Processor (DSP) delivers sharp color images
and excellent picture quality.
zLow light sensitivity 0.5 lux/F=1.2.
zWide-range automatic electronic shutter: up to 1/100,000.
zManual zoom lens with adjustable viewing range.
zPure Vision Technology.
PACKAGE CONTENTS
zCamera Unit x 1
zManual x 1
zExtension Power Cable x 1
2
OPTIONALACCESSORIES
•BA-ED- Mounting L-Bracket for ED Series Mini Dome Cameras
•EN220 5.6-inch LCD Test Monitor
3
SPECIFICATIONS
Pickup Device 1/3'' SONY Super HAD CCD
Video Format NTSC or PAL
Scanning System NTSC: 525 TV lines, 60 fields/sec
PAL: 625 TV lines, 50 fields/sec
Picture Elements 768 x 494(NTSC) ; 752 x 582(PAL)
Horizontal Resolution 560TVL
Sensitivity 0.5Lux/F=1.2
S/N Ratio Over 48dB(AGC off)
Electronic Shutter 1/50(1/60)~1/100,000
Lens Type
Vari-focal lens, Auto Iris
f= 2.9~10mm
f=3.8~9.5mm
f=9~22mm
Back Light Comp. ON/OFF Switch
Auto Gain Control ON/OFF Switch
Flickerless ON/OFF Switch
Auto White Balance Yes
Gamma Correction 0.45
Video Output
2 video outputs
BNC 1.0Vp-p, 75ohm
Additional testing video output 1.0Vp-p, 75ohm
Sync. Mode Internal Sync
Power Source 12VDC/24VAC
Dimensions 108(O.D) x 80(D) mm ; 4.3"(O.D) x 3.1"(D)
Weight 0.3 kg ; 0.7lbs
Operating Temperature 0°C~40°C ; 32°F~104°F (20%~80% Humidity)
4
DIMENSIONS
a.
b.
.
5
MAJOR PARTS FUNCTIONS
(1) Camera Cover
This cover will protect the camera from dust and damage.
(2) Lens
ED350 and ED300 come with vari-focal lens. ED200, ED230/330 comes with fixed lens. This
Vari-Focal Lens allows users to adjust the Zoom and Focus manually.
(3) Base
The camera unit is set in the dome base when it is shipped from the factory.
(4) Focus Ring
3
2
4 5
1
7
6
7
8
9
6
To set the focus, loosen the Focus ring knob first, then turn the ring toward <∞> or <N> as
necessary. When the focus is obtained as desired, tighten the focus ring knob.
(5) Zoom Ring
Loosen the zoom ring knob, then you can adjust the viewing range. Turn the ring towards <W>
for WIDE or <T> for TELE as necessary. When the setting is finished, tighten the zoom ring
knob.
(6) Power input
Use the connector to connect with 12VDC/24VAC power adaptor.
(7) Video Output BNC Connector
Use the connector to connect with the video in connector of a monitor.
(8) DIP Switch and ALC/Iris adjuster
Use this for detail camera setting including AGC, Backlight Compensation, Flickerless, Iris.
Please see the detail in Camera Setting Section.
(9) Ground Pin
For monitor use. When setting up the camera, connect a monitor to this video output pin and to
the GROUND pin using alligator clip cables, then use the image displayed on the monitor, set the
surveillance angle.
7
INSTALLATION
This section cover simple steps and detail installation. Please follow instruction for
preventing any unnecessary damage.
Simple Steps:
1. Open Camera Cover
2. Mount Camera on Ceiling
3. Connect power, video
4. Optional Connect to EN220 Test Monitor for field testing (monitor is not included)
5. Adjust Lens
6. Adjust camera setting on Dip Switch
Detail installation:
1. Open Camera Cover
Turn Clockwise to open it gently. Be careful not to damage the lens.
2. Mount the camera on ceiling. Refer dimension b for drilling dimension.
8
3. Connect Power and Video
a. Connect the BNC connector of the camera to a color monitor, or other video device
through a 75 ohm type coaxial cable with BNC female connector at cable
extension.
b. ED Series support dual power source. Connect either 12VDC or 24VAC regulated
power source to the camera. Please use power extension for connecting to it if the
power adapter cable is not long enough.
Note!! When connect to 12VDC. Please make sure you connect power +,-
correctly. Wrong Connection damage the camera.
c. Connect the audio ( only for model with Audio)
4. Optional Connect to EN220 Test Monitor for field testing (monitor is not
included)
It is highly recommend to use Everfocus Test Monitor to test the camera. Find the
Video testing connector as following. Connect it to testing monitor for field
testing.
.
White (+)
Black (-)
Video out
9
5. Zoom and focus adjustments
After the camera was installed, the zoom and focus of the
lens must be adjusted.
1. Loosen the zoom ring knob, and then turn the ring
towards <W>or <T>as necessary to obtain the
desired view range.
W side (Zoom out)
The viewing range will be wider and the subject is
smaller.
T side (Zoom in)
The viewing range will be smaller and the subject is larger.
2. Loosen the focus ring knob, then turn the ring towards <∞>or <N>as necessary to obtain
the clear video image.
3. Repeat steps 1 and 2 until the best image is obtained. Once the lens setting finished, tighten
the zoom ring and the focus ring knobs.
Otros manuales para ED350
3
Tabla de contenidos
Otros manuales de Cámara de seguridad de EverFocus
EverFocus
EverFocus ECZ 330 Manual del propietario
EverFocus
EverFocus EAN7221 Manual de usuario
EverFocus
EverFocus ED200E Manual de usuario
EverFocus
EverFocus EQ900F Series Manual de usuario
EverFocus
EverFocus EAN3200 Manual de usuario
EverFocus
EverFocus EHD935 eZ.HD Series Manual de usuario
EverFocus
EverFocus NeVio EAN900 Manual de usuario
EverFocus
EverFocus ED910 Manual de usuario
EverFocus
EverFocus EDH5210B Manual de usuario
EverFocus
EverFocus Speed Dome EPTZ3100I Manual de usuario
EverFocus
EverFocus EHD150 Manual de usuario
EverFocus
EverFocus EPN4122 Manual de usuario
EverFocus
EverFocus ED300 Series Manual de usuario
EverFocus
EverFocus ED710 Manual de usuario
EverFocus
EverFocus EZ350 Manual de usuario
EverFocus
EverFocus EHD630s Manual de usuario
EverFocus
EverFocus EDH5102 Manual de usuario
EverFocus
EverFocus EPTZ3600 Manual de usuario
EverFocus
EverFocus NeVio EZN850 Manual de usuario
EverFocus
EverFocus EPTZ3150 Manual de usuario
