ESAB TR-29 Manual de usuario

INSTRUCTIONS for

TR-29 TWO CYLINDER TRUCK KIT

Item No. 37924

for mounting:

353cv, 453cv, 653cvcc, MultiPower 460 and MultiPower 460 Pulse Power Sources

F15-592-B

March, 2003

This kit includes the following components:

1 — Assembled TR-29 Truck Body

1 — Cylinder Support

2 — Chain, 2/0 36" (not illustrated)

2 — Nuts 1/4" x 20 Lock

2 — Washer 1/4" Fender

4 — Screws 1/4"-20 1" Long

F15-592-B

Location of Screws

and U-Slots.

To mount Power Source on Truck, proceed as fol-

lows:

1. Carefully lift the power source off the floor with a

craneorhoistandremoveanyskidsfromthebase.

2. Lower the unit onto the truck base aligning the two

protruding screws on the rear bottom of the power

source (see photos above), with the U-slots pro-

vided in the truck base. The rear slots are located

just in front of the wheel guards. Note also that all

protruding bolt heads on the bottom of the power

sourcehaveaholedrilled in the truck floor for them

to pass through. When the Power Source is prop-

erly seated on the truck the weight of the unit is on

the floor of the truck not the side rails, and the front

floor of the truck will be flush with the lower front

panel of the Power Source.

Weight Bearing Area

(OPTIONAL)

- Install 1/4-20 Lock Nuts

on these screws once

assembled to the Truck Kit.

4. The cylinder support is installed by first removing

the four corresponding (assembly screws) on the

topfourcornersofthepower source.(SeeFigure4

onreverseside.) Setthesupportontopofthepower

sourceandinstallthelonger screwsprovided. (Note)

If top does not lay flush, loosen screws on handle

and retighten after assembly.

3. If bolting the power source to the base, 2 screws

should protrude through the TR-29 Floor from the

base of the power source. Attach one .250 flat

washer and one .250 lock nut to each screw.

This truck assembly is not intended to be hoisted

while attached in any way to a power source. If the

unit must be hoisted, the truck assembly must be

removed.

NEVERATTEMPT TOLIFTAPOWERSOURCE WITH

CYLINDER(S)ATTACHED!

5. Adjust cable strain relief bar to suitable height (see

Figure 3).

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Figure 1

Figure 2

6. To mount cylinders on completed assembly:

Slide at least the second link of each chain (678944)

into the center slot of the cylinder support.

Whenyou putthecylinders in place,pullthe chaintightly

aroundeach cylinder andslidea chain link intotheouter

slotof the cylinder support. Besure to pull the linkdown

firmly into each slot to secure the chain so that there is

littleslack of the chain about the cylinder. DO NOTjust

"loop" a link over the end of the support.

Cylinder support

assembly screws

Handle

Floor of Truck is flush

with lower panel of

Power Source.

Cable Strain Relief Bar

F15-592-B 03 / 2003

Figure 3 Figure 4

Assembly Screws on

Left Side not visible.

READ & UNDERSTAND THIS LABEL

PROTECT YOURSELF AND OTHERS

LIRE & COMPRENDE CETTE ETIQUETTE

VOUS PROTEGER ET LES AUTRES

Lifting eye to be used for lifting

power source ONLY.

Do NOT use when additional accessories

are attached to power source.

L’oeil d’ascenseur etre utilise

pour la source de pouver seulement.

ont attachesa la source de pouvoir.

PRUDENCE

P/N 99512240-C 3/22/02

Este manual sirve para los siguientes modelos

Otros manuales de Accesorios de soldadura de ESAB

ESAB

ESAB TWECO SPRAY MASTER V250 Guía de mantenimiento y servicio

ESAB

ESAB WeldCloud Mobile Manual de usuario

ESAB

ESAB PEI Manual de usuario

ESAB

ESAB Arc Master ICE A6 S Manual de usuario

ESAB

ESAB SAVAGE A40 Manual de usuario

ESAB

ESAB PSF 305 Manual de usuario

ESAB

ESAB A6 GMD Manual de usuario

ESAB

ESAB Cigweld ProGuard Manual de usuario

ESAB

ESAB A6S Arc Master Manual de usuario

ESAB

ESAB Sentinel A50 Manual de usuario

ESAB

ESAB Origo Feed 304 P4 Guía

ESAB

ESAB SDF-250 Manual de usuario

ESAB

ESAB EFU 30 Manual de usuario

ESAB

ESAB A2 S GMAW Mini Master Manual de usuario

ESAB

ESAB Warrior Feed 304 Manual de usuario

ESAB

ESAB MT-400EHD Manual de usuario

ESAB

ESAB SAVAGE A40 Manual de usuario

ESAB

ESAB PSF 260C Manual de usuario

ESAB

ESAB A6 Mastertrac Manual de usuario

ESAB

ESAB TIGAID315 AC/DC Manual de usuario

ESAB

ESAB ET 17 Manual de usuario

ESAB

ESAB Sentinel A60 Manual de usuario

ESAB

ESAB A6 VEC Manual de usuario

ESAB

ESAB Aristo U6 Manual de usuario

Manuales populares de Accesorios de soldadura de otras marcas

Lincoln Electric

Lincoln Electric LT-7 Tractor Manual de usuario

Weco

Weco Trolley R Manual de usuario

Cornwell Tools

Cornwell Tools MMWC1 Manual de usuario

Dohle

Dohle ExOn2A Manual de usuario

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manual de usuario

3M Speedglas 9100 Series Manual de usuario

Miller Electric

Miller Electric OM-842 Manual de usuario

Miller

Miller A-200 Series Manual de usuario

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manual de usuario

optrel

optrel lifeflip autopilot Manual de usuario

Miller

Miller MIGmatic M-25 Manual de usuario

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manual de usuario

Abicor Binzel

Abicor Binzel xFUME PRO Manual de usuario

Sealey

Sealey SR20.V2 Manual de usuario

iWeld

iWeld NORED EYE Manual de usuario

Sthor

Sthor 74483 Manual de usuario

Leister

Leister TWINNY T7 Manual de usuario

Miller

Miller I-22 CE Manual de usuario