Eneo VK-1321/PIR Manual de usuario
1
Instruction Manual
Hidden CCD Camera VK-1321/PIR (B&W),
VKC-1338/PIR (Colour)
2
3
Contents
1. Safety Instructions ......................................................................................... 2
2. Description .................................................................................................... 3
3. Installation ..................................................................................................... 4
4. Wiring Instructions......................................................................................... 5
5. PIR Detector Board Installation and Descriptions ............................................ 6
6. Specications ................................................................................................ 9
7. Dimensional Drawings ................................................................................. 11
1. Safety Instructions
• Read these safety instructions and the operation manual rst before you install
and commission the camera.
• Keep the manual in a safe place for later reference.
• Contact your local dealer in case of malfunction.
• Protect your camera from contamination with water and humidity to prevent it
from permanent damage.
Never switch the camera on when it gets wet. Have it checked at an authorized
service center in this case.
• To disconnect the power cord of the cameras, pull it out by the plug.
Never pull the cord itself.
• Do not open the camera housing.
Maintenance and repair have to be carried out only by authorized service centers.
• Operate the camera only at a temperature range of -10°C to +50°C and at
a humidity of max. 90%.
• The camera is equipped with an automatic gain control (AGC) which increases
the sensitivity at low light levels.
Noisy pictures at these conditions are quite normal.
2
3
• Pictures including bright spotlights will cause perhaps vertical lines (smear) or
soft edges (blooming) on the monitor display. This happens most probably in
automatic shutter mode (AES).
This is not a defect but an effect caused by the CCD sensor.
• With darkened environment, and direct view into the IR lighting, is to be kept a
safety margin from >1m to the IR LEDs.
• Use only a mild detergent to clean the housing.
Never use dilution or gasoline for this can cause permanent damage to
the surface.
The cameras should never:
• be operated beyond the technical specications. This can lead to destruction.
• pointed with open iris towards the sun. (This can damage the sensor).
Note: This is a class A digital device. This digital device can cause harmful
interference in a residential area; in this case the user may be required
to take appropriate corrective action at his/her own expense.
2. Description
This B/W (Colour) HIDDEN CCD Camera uses high sensitive 1/3” interline transfer
CCD Image Sensor (CCD = Charge Coupled Device), and all state circuitry which
provides extremely long life and high reliability.
This Camera offers excellent image quality with low lag and high burn resistance,
and is not subject to distortions from magnetic elds.
Highly resistance to shock and vibration, and easy to install this Camera is a very
good choice for your B/W (Colour) CCTV system.
4
5
3. Installation
1. Secure the bracket to the wall with screws (included).
2. Attach the Camera Case to the bracket.
4
5
3. Adjust the vertical and horizontal angles by loosening screws (A&B) and
by turning the bracket vertically and horizontally.
4. Wiring Instructions
1. Connect the coaxial cable between the camera and the monitor using a 75ohms
coaxial cable.
2. Insert the AC plug into the AC power socket and the DC plug to the DC Jack.
Note: AC Adapter Sold separately (see Accessories)
Monitor to 24VDC
6
7
5. PIR Detector Board Installation and Descriptions
1
N.C.
2
J4
J1
JP2
VR2
J2
VR1
N.O.
1
2
3
4
5
6
PULSE
Output Terminals
Pulse Count
Light Control
Recording Control
Time Adjustment
LED Selector
Sensitivity
Adjustment
Options Description
1. LED Selector
(3 pins: Top, Center, Bottom)
A. Top + Center w/black cap: Upon walk-testing:
Light blinking (disadvantages: Easy to identify
as a security system.)
B. Center + Low w/black cap: No light blinking
while detecting. (advantages: less obvious)
2. Sensitivity Adjustment A. To raise sensitivity: Turn clockwise to detect
longer distance and wider pattern.
B. To lower sensitivity: Turn counter clockwise
for detection in narrow areas.
3. Dwell Time Adjustment
Adjustable
from 2 to 40 sec.
For closure period of N.C/N.O relay connected to
an alarm panel, light control or recording control
of time lapse VCR, etc.
A. Max. time: Turn counter clockwise
B. Min. time: Turn clockwise
Top + Center pins of „J4” must be selected
to adjust the time setting.
J1
High Low
„VR1”
Min. Max.
„VR2”
6
7
Options Description
4. Alarm control, Light
control or Recording
control (N.O or N.C)
(3 pins: Top, Center,
Bottom)
A. Top + Center w/black cap: Operate with „VR2”
to adjust time. (To set the relay output of the
Light control or Recording control, the time is
selected by individual preference or application.
B. Center + Bottom w/black jumper: Relay output
can be set for Security control panel for only
2 seconds.
Note: N.C./N.O. relay output current:
1A 125VAC, 2A 30VDC.
5. Pulse Control
Once or twice
4 pins: 2PAIRS w/jumper
connector
Position 1: Set to „ONCE” for instant reaction when
PIR detects someone: and either the
„alarm or Security control panel” or
„Recording control” will be triggered
immediately.
Position 2: Set to „Twice” when PIR detects
someone 2 times within 15 seconds.
6. Output Terminals
24 Hour/Anti-Tamper
N.C.: Normally Closed
A. For connection to: Security panel or
Light control CCTV
...etc.
B. With anti-tamper function for 24 hours.
N.O.: Normally Open Contacts
Note: Relay output current:
1A 125VAC, 2A 30VDC
7. Power: 12VDC
Standby Current: 3mA,
Working Current: 28mA
Caution:
The PIR is triggered by body movement,
excluding xed objects, however, do not place
in direct sunlight or reected sunlight.
J4
N.C. N.O.
J2
2
1
JP2
8
9
• Wide angle lens up to 100°, coverage areas to 30x30 feet
• Provide 64 beans in 3 layers
100° Top view
Side view
10 20 30 feet 10 20 30 feet
8
9
6. Specications
Model VK-1321/PIR VKC-1338/PIR
EDP No. 91989 91991
Automatic white balance
(AWB)
Supplied
Imager 1/3“ Sony Super HAD Interline Transfer CCD
Picture elements Approx. 440,000 (H) 752 x (V) 582
System CCIR CCIR/PAL
Synchronization Internal
Sensitivity
at 50% video signal
0.65Lux at F2.0 /
0.23Lux at F1.2
(VT measurement result)
5.6Lux at F2.0 /
2.0Lux at F1.2
(VT measurement result)
Horizontal resolution 600 TV lines 470 TV lines
Signal-to-noise ratio 48dB (AGC OFF)
Automatic gain control
(AGC)
Supplied
Automatic shutter
control (AES)
1/50 ~ 1/100,000sec.
Gamma correction 0.45
Lens F2.0/3.7mm pinhole
Horizontal angle of view 68°
External connections Video (BNC), 12VDC (DC socket)
Video output 1Vp-p, VBS, 75ohms 1Vp-p, CVBS, 75ohms
Supply voltage 12VDC ±10%
Power consumption 1.44watts 2.5watts
Temperature range -10° ~ +50°C
Housing Plastic
Mounting Wall mount (bracket included)
Colour Light grey
Dimensions See drawing
Weight 110g 125g
10
11
Accessories
EDP No. Description
70447 Plug-in Power Supply Unit 100-240VAC
77772 PSU 12VDC/0.5A, Regulated, Desktop
77779 Plug-in Power Supply Unit 230VAC/12VDC
Model VK-1321/PIR VKC-1338/PIR
EDP No. 91989 91991
Special features PIR sensor function.
NO/NC relay contact output (125VAC/1A, 30VDC/2A
resisitive), adjustable switching duration: 2 ~ 40sec.
sensor eld angles: 100° horizontal / 45° vertical,
detection range: up to 10m
Otros manuales para VK-1321/PIR
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Eneo
Eneo
Eneo IPD-52F0028MAA Manual de usuario
Eneo
Eneo ICB-62M2712M0A Manual de usuario
Eneo
Eneo IPD-62M2712P5A Manual de usuario
Eneo
Eneo VKC-13130F2810IR Manual de usuario
Eneo
Eneo ITB-7SF0075M0A Manual de usuario
Eneo
Eneo INP-7 Series Manual de usuario
Eneo
Eneo IEB-62F0036M0A Manual de usuario
Eneo
Eneo VKC-1425 Manual de usuario
Eneo
Eneo TPP-72A0030P0A Manual de usuario
Eneo
Eneo IPP-62A0012M0A Manual de usuario
Eneo
Eneo VKC-1340/IR Manual de usuario
Eneo
Eneo NXD-2030PTZ1080IR Manual de usuario
Eneo
Eneo MED-62V2713M0A Manual de usuario
Eneo
Eneo VKCD-1323/IR Instrucciones de instalación
Eneo
Eneo IPP-88A0030MIA Manual de usuario
Eneo
Eneo PXD-1110F39 Instrucciones de instalación
Eneo
Eneo 213021 Manual de usuario
Eneo
Eneo VKC-12140F2810IR Manual de usuario
Eneo
Eneo VKC-14140F2810IR Instrucciones de instalación
Eneo
Eneo HDD-2080Z03IR D Manual de usuario
