Eneo NXC-1502M Manual de usuario

NXC-1502M

Full HD NETWORK CAMERA

Please read this manual thoroughly before use and keep it handy for future reference.

NXC-1502M, Quick Installation Guide

1. Description

This manual applies to the NXC-1502M network camera.

The Network Camera supports the network service for a sensor image with progressive scan which

can be monitored on a real-time screen regardless of distances and locations. By using its dedicated

program many users are able to have an access to the Network Camera at once or a single user can

monitor various network cameras at the same time. It also enables users to play store and retrieve a

monitoring image by using a PC. All the settings and real-time monitoring screens are also provided

through an access to the web.

The Network Camera is fully featured for security surveillance and remote monitoring needs. It is

based on the DSP compression chip and makes it available on the network as real-time full frame

rate Motion JPEG and H.264 (or MPEG-4) video streams.

The alarm input and alarm output can be used to connect various third party devices such as door

sensors and alarm bells.

• Installation teps

Follow these steps to install the Network Transmitter on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the Network Camera. See page 3.

3. Set an IP address. See page 4.

4. Set the password. See page 5.

• Package Component

The system comes with the following components:

Network Camera unit Installation CD Installation Guide Accessory Kit

• Contents in the installation CD

1. The Network Camera User’s Manual

2. The NautilusClient16 User’s Manual

3. The Nautilus Server User’s Manual

4. The NautilusClient16 Installation software

5. The Nautilus Server Installation software

Note: Check your package to make sure that you received the complete system including all

components shown above.

NXC-1502M, Quick Installation Guide

• Front View

NO Function

1 Focus adjusting fixing screw

2 Auto IRIS lens connector

• Rear View

NO Function Description

1 Power Adaptor Terminal Main Power, 2pin terminal, DC12V/AC24V 330mA(4.0W)

2 Power Indicator(Green) Indicates power input.

Status Indicator(Red) Indicates camera status.

3 Audio Input Audio Input Stereo Jac

Audio Output Audio Output Stereo Jac

4 Network Connector (PoE) RJ-45 port compatible with 10/100Mbps, which have a PoE

function.

5 Video Switch Selects Video On/Off. Set to On to output a video si

nal.

The video image is shown only for 30 seconds.

6 Video Output Connects the video output.

his BNC connector provides a

1.0Vp-p/75 ohms composite video signal.

7 Micro SD Card Slot Card Slot for Micro SD. Open the protection cover with a

supported tool to insert Micro SD card.

8 3pin Terminal IO Connects alarm In/Out.

2pin RS485 Terminal Connects PT device.

9 Reset Button Executes the factory default.

NXC-1502M, Quick Installation Guide

• LED Indicators

LED Color Indication

Network

Green

Steady for connection to a 100 Mbit/s network.

Flashes for

network activity.

Amber

Steady for connection to 10 Mbit/s network.

Flashes for

network activity.

Unlit

No network connection.

Status Red

Steady red for failed upgrade or booting.

Power Green

Steady green for normal operation or booting.

Flashes green during firmware upgrade.

Note: Steady green and red during booting. Flash green and red during factory default.

2. Installation

2.1 Connection

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC while a direct cable is used for connection

to a hub.

• Connecting Alarms

AI(Alarm In) :

You can use external devices to signal the network camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.

G(Ground) :

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

Alarm Out :

The network camera can activate external devices such as buzzers or lights. Connect the device

to the AO (Alarm Out) and G (Ground) connectors.

• Connecting Video Output

Video Output is used for an easy zoom and focus control when installing lens. Set Video Switch to

On position to output the video signal. Video Output is restricted to VGA(640x480) resolution.

Caution: After lens installation you must set Video Switch to Off position to provide the best

performance of the Network Camera.

• Connecting the Power

Connect the power of DC12V or AC24V 330mA for the network camera. Connect the positive(+)

pole to the ‘+’ position and the negative(-) pole to the ‘-‘ position for the DC power.

NXC-1502M, Quick Installation Guide

2.2 Network Connection and IP assignment

The Network Camera supports the operation through the network. When a camera is first connected

to the network it has no IP address. So it is necessary to allocate an IP address to the device with the

“Smart Manager” utility on the CD.

1. Connect the Network Camera / device to the network and power up.

2. Start SmartManager utility ( All programs > NautilusClient16 > SmartManager) the main window

will be displayed after a short while any network devices connected to the network will be

displayed in the list.

3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu

as below.

4. Select Assign IP. You cam see a Assign IP window. Enter the required IP address.

Note: For more information refer to the Smart Manger User’s Manual.

NXC-1502M, Quick Installation Guide

3. Operation

The Network Camera can be used with Windows operating system and browsers. The recommended

browsers are Internet Explorer Safari Firefox Opera and Google Chrome with Windows.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the Network Camera in the Location/Address field of your

browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

4. The encoder’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet once connected the Network Camera is accessible on your local network

(LAN). To access the video encoder from the Internet you must configure your broadband router to

allow incoming data traffic to the video encoder. To do this enable the NAT-traversal feature which

will attempt to automatically configure the router to allow access to the video encoder. This is enabled

from Setup > System > Network > NAT.

For more information please see “3.5.5 System>Network>NAT” of User’s Manual.

NXC-1502M, Quick Installation Guide

3.3 etting the admin password over a secure connection

To gain access to the product the password for

the default administrator user must be set. This

is done in the “Admin Password” dialog which is

isplayed when the network

camera

is accessed

for the setup at the first time.

Enter your admin

name and password set by the administrator.

Note: The default administrator username and

password is “admin”. If the password is lost the

Network Camera must

be reset to the factory

default settings.

See “3.6 Resetting to the Factory

Default Settings

”.

3.4 Live View Page

The live view page comes in eight

screen modes like

1920x1080

1280x1024 1280x720 720x4

80(576)

640x480 352x240(288)

and

320x240

. Users are allowed to select

the most suitable one out of those

modes. Please adjust the mode in

accordance with your PC

specifications and monitoring

purposes.

1) General controls

Live View Page Search & Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. For more information please see “3.5.1 Basic Configuration >

Video & Image” of User’s Manual.

The resolution drop-down list allows you to select the most suitable one

out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of

protocols and methods to use depends on your viewing requirements and on the properties of

your network.

NXC-1502M, Quick Installation Guide

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

video stream.

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

The Camera Menu button activates a pop-up window for camera menu control.

Use this scale to control the volume of the speakers.

Use this scale to control the volume of the microphone.

Use this scale to control the volume of the speakers and microphones.

3) Video and Audio treams

The video encoder provides several images and video stream formats. Your requirements and the

properties of your network will determine the type you use.

The Live View page in the video encoder provides access to H.264 MPEG-4 and Motion JPEG

video streams and to the list of available video streams. Other applications and clients can also

access these video streams/images directly without going via the Live View page.

NXC-1502M, Quick Installation Guide

3.5 Network Camera etup

This section describes how to configure the network camera and is intended for product

Administrators who have unrestricted access to all the Setup tools; and Operators who have access

to the settings for Basic Live View Video & Image Audio Event and System Configuration.

You can configure the network camera by clicking Setup in the top right-hand corner of the Live View

page. Click on this page to access the online help that explains the setup tools

When accessing the Network Camera for the first time the

“Admin Password” dialog appears. Enter your admin name

and password set by the administrator.

Note: If the password is lost the Network Camera must

be reset to the factory default settings.

See “3.6 Resetting to the Factory Default Settings”.

3.6 Resetting to the factory default settings

To reset the Network Camera to the original factory settings go to the Setup>System >Maintenance

web page (described in “3.5.6 System>Maintenance” of the User’s Manual) or use the control button

on the network camera as described below:

Follow the instructions below to reset the Network Camera to the factory default settings using the

Reset Button.

1. Switch off the Network Camera by disconnecting the power adapter.

2. Press and hold the Control Button with a straightened paperclip while reconnecting the power.

3. Keep the Control button pressed until the Status and Power indicator blink.

4. Release the Control Button.

5. When the Power Indicator changes to Green (may take up to 1 minute) the process is complete

and the network video transmitter has been reset.

6. The transmitter resets to factory defaults and restarts after completing the factory reset.

CAUTION: When performing a Factory Reset you will lose any settings you have saved.

3.7 More Information

For more information please see the Network Camera User’s Manual which is available on the CD

included in this package.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Eneo

Eneo

Eneo Minitrax HDD-1012PTZ1080 Manual de usuario

Eneo

Eneo VKCD-1326/IR Manual de usuario

Eneo

Eneo MEP-63M2812M0A Manual de usuario

Eneo

Eneo ISM-72F0021W0A Instrucciones de instalación

Eneo

Eneo VKC-1424-36 Manual de usuario

Eneo

Eneo EDC Series Instrucciones de instalación

Eneo

Eneo IEB-62F0036P0A Manual de usuario

Eneo

Eneo Fastrax III EDC-3362 Manual de usuario

Eneo

Eneo NXC-1403F03 Manual de usuario

Eneo

Eneo PXD-2080MIR C Manual de usuario

Eneo

Eneo HDD-2018PTZ1080 Manual de usuario

Eneo

Eneo VKC-1327CW3 Manual de usuario

Eneo

Eneo HDB-2180Z03IR Manual de usuario

Eneo

Eneo HDD-2000MIR720 Manual de usuario

Eneo

Eneo VKC-1324A/W3 Manual de usuario

Eneo

Eneo IED-62F0036M0A Manual de usuario

Eneo

Eneo NXD-980IR37P B Instrucciones de instalación

Eneo

Eneo IPD-73M2812MWA Manual de usuario

Eneo

Eneo VKC-1416B-/PP Manual de usuario

Eneo

Eneo MED-62V2812M0A Manual de usuario

Eneo

Eneo 230800 Manual de usuario

Eneo

Eneo IPC-52A0003M0B Manual de usuario

Eneo

Eneo HDB-1080Z03IR B Manual de usuario

Eneo

Eneo IPD-52F0028MAA Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario