Endress+Hauser Proline t-mass B 150 Especificaciones técnicas
Brief Operating Instructions
Proline t-mass B 150
Thermal Mass Flow Measuring System
These Instructions are Brief Operating Instructions; they do not replace the
Operating Instructions included in the scope of supply.
For detailed information, refer to the Operating Instructions and other
documentation on the CD-ROM provided or visit www.endress.com/
deviceviewer.
KA01104D/06/EN/01.12
71165082
Table of contents Proline t-mass B 150
2 Endress+Hauser
Table of contents
1 Document information ...................................... 3
1.1 Document conventions ........................................... 3
2 Basic safety instructions ...................................... 5
2.1 Requirements for the personnel ....................................... 5
2.2 Designated use ............................................... 5
2.3 Workplace safety .............................................. 6
2.4 Operational safety .............................................. 6
2.5 Product safety ................................................ 6
3 Product description ......................................... 7
3.1 Product design ............................................... 7
4 Incoming acceptance and product identification ..................... 8
4.1 Incoming acceptance ............................................ 8
4.2 Product identification ............................................ 9
5 Storage and transport ...................................... 10
5.1 Storage conditions ............................................. 10
5.2 Transporting the product .......................................... 10
5.3 Packaging disposal ............................................. 10
6 Installation .............................................. 11
6.1 Installation conditions ........................................... 11
6.2 Mounting the measuring device ...................................... 16
6.3 Post-mounting check ............................................ 18
7 Electrical connection ....................................... 20
7.1 Connection conditions ........................................... 20
7.2 Connecting the measuring device ...................................... 21
7.3 Ensuring the degree of protection ...................................... 22
7.4 Post-connection check ........................................... 23
8 Operation options ......................................... 24
8.1 Structure and function of the operating menu ................................ 24
8.2 Access to the operating menu via the local display .............................. 26
8.3 Access to the operating menu via the operating tool ............................. 32
9 Commissioning ........................................... 33
9.1 Function check .............................................. 33
9.2 Switching on the measuring device ..................................... 33
9.3 Setting the operating language ....................................... 34
9.4 Configuring the measuring device ..................................... 34
9.5 Defining the tag name ........................................... 35
9.6 Protecting settings from unauthorized access ................................ 36
10 Diagnostic information and remedial measures ..................... 37
Proline t-mass B 150 Document information
Endress+Hauser 3
1 Document information
1.1 Document conventions
1.1.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious
or fatal injury.
WARNING
A0011190-EN
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
or fatal injury.
CAUTION
A0011191-EN
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor
or medium injury.
NOTICE
A0011192-EN
NOTICE
This symbol contains information on procedures and other facts which do not result in personal
injury.
1.1.2 Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage (sine-wave) is applied or through which alternating current flows.
)
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
*
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential equalization
line or a star grounding system depending on national or company codes of practice.
1.1.3 Tool symbols
A0011219 A0011220 A0011221 A0011222
Phillips head screwdriver Flat blade screwdriver Allen key Hexagon wrench
Document information Proline t-mass B 150
4 Endress+Hauser
1.1.4 Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
,…
,
Series of steps
ÃResult of a sequence of actions
1.1.5 Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,…
,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous location.
Proline t-mass B 150 Basic safety instructions
Endress+Hauser 5
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
►Trained, qualified specialists must have a relevant qualification for this specific function and
task
►Are authorized by the plant owner/operator
►Are familiar with federal/national regulations
►Before beginning work, the specialist staff must have read and understood the instructions in
the Operating Instructions and supplementary documentation as well as in the certificates
(depending on the application)
►Following instructions and basic conditions
2.2 Designated use
Application and media
The measuring device described in these Instructions is intended only for flow measurement of
gases.
To ensure that the measuring device remains in proper condition for the operation time:
►Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
►Based on the nameplate, check whether the ordered device is permitted for the intended use
in the hazardous area (e.g. explosion protection, pressure vessel safety).
►Use the measuring device only for media against which the process-wetted materials are
adequately resistant.
Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
If the sensor gland is opened, the accuracy specifications of the measuring device no longer apply.
In such situations, the measuring device must be removed and returned for recalibration and to
the manufacturer.
WARNING
Risk of injury if the process connection and sensor gland are opened under pressure.
►The process connection and the sensor gland should only be opened in an unpressurized state.
NOTICE
Dust and moisture can enter the transmitter when the transmitter housing is opened.
►Only open the transmitter housing briefly, ensuring that no dust or moisture enters the
housing.
NOTICE
Danger of breakage of the sensor due to corrosive or abrasive fluids
►Verify the compatibility of the process fluid with the sensor material.
►Ensure the resistance of all fluid-wetted materials in the process.
►Observe the specified maximum process pressure.
Basic safety instructions Proline t-mass B 150
6 Endress+Hauser
Verification for borderline cases:
►For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any warranty
or liability.
Residual risks
The external surface temperature of the housing can increase by max. 15 K due to the power
consumption of the electronic components. Hot process fluids passing through the measuring
device will further increase the surface temperature of the housing. The surface of the sensor,
in particular, can reach temperatures which are close to the fluid temperature.
Possible burn hazard due to fluid temperatures
►For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
►Wear the required personal protective equipment according to federal/national regulations.
For welding work on the piping:
►Do not ground the welding unit via the measuring device.
2.4 Operational safety
Risk of injury.
►Operate the device in proper technical condition and fail-safe condition only.
►The operator is responsible for interference-free operation of the device.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which they
are safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC directives
listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms this by
affixing the CE mark to the device.
Proline t-mass B 150 Product description
Endress+Hauser 7
3 Product description
3.1 Product design
1
2
22
23
24
25
26
27
7
Esc
123 4 56
8
A0017196
1 Electronics compartment cover
2 Display module
3 Terminal block
4 Electronics module
5 Cable gland
6 Transmitter housing
7 Sensor
8 S-DAT
Incoming acceptance and product identification Proline t-mass B 150
8 Endress+Hauser
4 Incoming acceptance and product identification
4.1 Incoming acceptance
A0015502
1
+
2
1
+
2
A0013843
A0013695
A0015502
A0013698
A0015502
A0013699
Proline t-mass B 150 Incoming acceptance and product identification
Endress+Hauser 9
A0015502
A0013697
If one of the conditions does not comply, contact your Endress+Hauser distributor.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
•Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is displayed.
For an overview of the scope of the Technical Documentation provided, refer to the following:
The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
Order code:
Ext. ord. cd.:
Ser. no.:
1
2
3
A0014053
å 1 Example of a nameplate
1 Order code
2 Serial number (Ser. no.)
3 Extended order code (Ext. ord. cd.)
For detailed information about interpreting the nameplate specifications, refer to the
Operating Instructions for the device on the CD-ROM provided
Storage and transport Proline t-mass B 150
10 Endress+Hauser
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
• Store in original packaging.
• Do not remove the protection cap mounted on the transducer.
• Protect from direct sunlight.
• Select a storage location where moisture cannot collect in the measuring device.
• Store in a dry and dust-free place.
• Do not store outdoors.
•Storage temperature(® ä 15)
5.2 Transporting the product
Observe the following notes during transport:
• Transport the measuring device to the measuring point in the original packaging.
• Do not remove the protection cap mounted on the transducer. It prevents mechanical damage
and contamination.
5.3 Packaging disposal
For detailed information about disposing of the packaging materials, refer to the Operating
Instructions for the device on the CD-ROM provided
Tabla de contenidos
Otros manuales de Instrumento de medición de Endress+Hauser
Endress+Hauser
Endress+Hauser SpectraSensors SS2100i-1 Manual de usuario
Endress+Hauser
Endress+Hauser RID14 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Waterpilot FMX21 Especificaciones técnicas
Endress+Hauser
Endress+Hauser LPGmass Manual de usuario
Endress+Hauser
Endress+Hauser Liquiline System CA80NO Especificaciones técnicas
Endress+Hauser
Endress+Hauser Proline Cubemass C 500 Manual
Endress+Hauser
Endress+Hauser Levelflex M FMP40 Manual de usuario
Endress+Hauser
Endress+Hauser Deltapilot S FMB70 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Stamosens CSM750 Manual de usuario
Endress+Hauser
Endress+Hauser Proline Cubemass C 100 PROFIBUS DP Manual de usuario
Endress+Hauser
Endress+Hauser RID14 Manual de usuario
Endress+Hauser
Endress+Hauser Liquiline CA80SI Manual de usuario
Endress+Hauser
Endress+Hauser Micropilot FMR60 Manual
Endress+Hauser
Endress+Hauser Proservo NMS5 Manual de usuario
Endress+Hauser
Endress+Hauser Liquicap M FMI52 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Proline Promag W 800 Manual de usuario
Endress+Hauser
Endress+Hauser PROFIBUS PA Levelflex FMP56 Manual de usuario
Endress+Hauser
Endress+Hauser Deltabar PMD78B Manual de usuario
Endress+Hauser
Endress+Hauser Ecograph T Especificaciones técnicas
Endress+Hauser
Endress+Hauser Gammapilot FMG50 Especificaciones técnicas
