Emerson Rosemount 648 Manual de usuario

Quick Start Guide

00825-0100-6129, Rev AB

February 2019

Rosemount™Wireless Dam Monitor

(WDM)

Special

00825-0100-6129_RevAB.fm Page 1 Wednesday, February 13, 2019 3:16 PM

February 2019

Quick Start Guide

Rosemount WDM

Rosemount WDM Hardware Revision

HART®Device Revision

Device Install Kit/DD Revision

Device Revision 1, DD Revision 1 or higher

NOTICE

This guide provides basic information for the Rosemount WDM special. It does not provide instructions for

detailed configuration, diagnostics, maintenance, service, troubleshooting, or installations.

Failure to follow these installation guidelines could result in death or serious injury.

Make sure only qualified personnel perform the installation.

Explosions could result in death or serious injury.

Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments are

installed in accordance with intrinsically safe or non-incendive field wiring practices.

Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous locations

certifications.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operations.

This device must be installed to ensure a minimum antenna separation distance of 20 cm from all person.

The black power module may be replaced in a hazardous area. The black power module has surface

resistivity greater than one giga-ohm and must be properly installed in the wireless device enclosure. Care

must be taken during transportation to and from the point of installation to prevent electrostatic charge

build-up.

NOTICE

Shipping considerations for wireless products: (lithium battery: black power module, model number

701PBKKF)

The unit was shipped to you without the black power module installed. Remove the black power module prior

to shipping the unit.

Each black power module contains two “C” size primary lithium batteries. Primary lithium batteries are

regulated in transportation by the U. S. Department of Transportation, and are also covered by IATA

(International Air Transport Association), ICAO (International Civil Aviation Organization), and ARD (European

Ground Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure compliance with

these or any other local requirements. Consult current regulations and requirements before shipping.

Contents

Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Physical installation . . . . . . . . . . . . . . . . . . . . . . . 5

Verify operation . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power module replacement . . . . . . . . . . . . . . . . 8

Product Certifications . . . . . . . . . . . . . . . . . . . . 10

00825-0100-6129_RevAB.fm Page 2 Wednesday, February 13, 2019 3:16 PM

Quick Start Guide

February 2019

1.0 Functionality

The intended use of this WDM special is to provide a solution for real-time

monitoring of applications in underground water level and pressure

management of an embankment dam to determine the stability of its structure.

An Impress strain gauge pressure sensor is connected directly to the WDM

which excites the sensor and measures the output. The WDM converts the

measured voltage to a pressure reading in PSI, meters of water or other units

and wirelessly transmits the reading as well. This solution eliminates the need

for solar panels and associated costly materials making it an inexpensive and

easy solution.

1.1 Wireless considerations

Power up sequence

The Rosemount WDM Special and all other wireless devices should be installed

only after the Wireless Gateway (“Gateway”) has been installed and is

functioning properly. Wireless devices should also be powered up in order of

proximity from the Gateway, beginning with the closest. This will result in a

simpler and faster network installation. Enable active advertising on the

Gateway to ensure new devices join the network faster. For more information,

see the Gateway Reference Manual.

Antenna position

The special is offered with both the external antenna (WK1) and the extended

range antenna (WM1). The antenna should be positioned vertically, either

straight up or straight down, and it should be approximately 3 ft. (1 m) from any

large structure, building, or conductive surface to allow for clear

communication to other devices.

Figure 1. Antenna Position

00825-0100-6129_RevAB.fm Page 3 Wednesday, February 13, 2019 3:16 PM

February 2019

Quick Start Guide

Conduit entry

Upon installation, ensure each conduit entry is either sealed with a conduit plug

using approved thread sealant, or has an installed conduit fitting or cable gland

with appropriate threaded sealant.

Figure 2. Conduit Entry

A. Conduit entry

Field Communicator connections

The black power module needs to be installed in the device for the Field

Communicator to interface with the Rosemount WDM Special. For HART

Wireless Transmitter communication via a Field Communicator, a Rosemount

WDM Device Dashboard (DD) is required. See “Configuration” on page 6 for

more information regarding the WDM DD.

Refer to Figure 3 for connecting the Field Communicator to the Rosemount

WDM Special.

Figure 3. Connection

COMM

P/N00753-9200-0020

#K1197

WHT

BRN

YEL

GRN

00825-0100-6129_RevAB.fm Page 4 Wednesday, February 13, 2019 3:16 PM

Quick Start Guide

February 2019

2.0 Physical installation

2.1 Vent tube installation

The vent tube needs to be exposed to atmosphere in a dry environment. During

installation, protect the end of the cable from water ingress. Do not remove the

cover on the cable until the end is at the point of connection.

Note

The maximum bend radius for polyurethane cable is 11/2inches. If bent further, the vent

tube in the cable may kink causing measurement errors.

Follow sensor manufacturer’s installation recommendations.

2.2 Wiring terminal block

The terminal block uses color abbreviations for the color wire from the Impress

pressure sensor that goes with each terminal lug on the terminal block label

(Figure 4).

The four wires from the sensor must be connected to the corresponding colors

on the label. Ground according to your facility standard practices.

Ground the sensor cable shield to a ground outside or inside of the transmitter

terminal compartment. The cable shield should be trimmed close and insulated

to keep it from touching the other sensor wires or terminals.

Only power this device with the 701PBKKF power module and only connect

Impress Strain Gauge on the terminals.

Figure 4. Terminal Wire Colors

WHT – White YEL – Yellow

BRN – Brown GRN – Green

00825-0100-6129_RevAB.fm Page 5 Wednesday, February 13, 2019 3:16 PM

February 2019

Quick Start Guide

3.0 Verify operation

Operation can be verified using four methods at the device via the LCD display,

using the Field Communicator, at the Gateway via the Gateway’s integrated

web server, or using AMS™ Wireless Suite or AMS Device Manager.

3.1 LCD display

During normal operation, the LCD display will show the PV value at the

confirmed update rate. Refer to the Reference Manual for error codes and other

LCD display messages. Select the Diagnostic button to display the TAG, Device

ID, Network ID, Network Join Status, and Device Status screens.

3.2 Configuration

For HART Wireless transmitter communication via a Field Communicator or

AMS Device Manager, a Rosemount WDM Device Dashboard (DD) is required.

Contact the Rosemount Wireless Specialist Team

(RMT-NA.SpecialistWirel[email protected]) to obtain the DD.

To provide accurate sensor readings, values from each sensor data sheet need

to be configured and stored in the Rosemount WDM Transmitter. Navigate to

Configure > Manual Setup > Sensor > Sensor Setup > Data Sheet Values.

The special configuration items the user will need to enter are those provided

(i.e. Range, Supply Voltage, 0%, 50%, and 100%). These values can be found in

the custom data sheet sent with each sensor.

Searching for

network Joining network Connected with

one parent

Connected with

two parents

n e t w k

A -s r c h

n e t w k

J O I N G

n e t w k

1 P A R N T

n e t w k

2 P A R N T

00825-0100-6129_RevAB.fm Page 6 Wednesday, February 13, 2019 3:16 PM

Quick Start Guide

February 2019

The communication status may be verified in the wireless device using the

following Fast Key sequence.

3.3 Wireless Gateway

If the Rosemount WDM Special was configured with the Network ID and Join Key

and sufficient time for network polling has passed, the transmitter will be

connected to the network. To verify device operation and connectivity using the

Gateway's web based user interface, navigate to the Devices page. This page will

also display the transmitter's tag, PV, SV, TV, QV, and Last Update time. Refer to

the Gateway Manual Supplement for terms, user fields, and parameters used in

the Gateway web based user interface.

Note

The time to join the new device(s) to the network is dependent upon the number of

devices being joined and the number of devices in the current network. For one device

joining an existing network with multiple devices, it may take up to five minutes. It may

take up to 60 minutes for multiple new devices to join the existing network.

Note

If the device joins the network and immediately has an alarm present, it is likely due to

sensor configuration. Check the sensor wiring (see “Power module replacement” on

page 8) and the sensor configuration (see Table 3 on page 8).

Figure 5. Gateway Network Settings

Table 1. Rosemount WDM Fast Key Sequence

Function Fast Key sequence Menu items

Communications 3, 4 Comm, Join Mode, Neighbor Count, Advertisement

Count, Join Attempts

00825-0100-6129_RevAB.fm Page 7 Wednesday, February 13, 2019 3:16 PM

February 2019

Quick Start Guide

4.0 Troubleshooting

If the device is not joined to the network after power up, verify the correct

configuration of the network ID and join key, and verify that Active Advertising

has been enabled on the Gateway. The network ID and join key in the device

must match the network ID and join key of the Gateway.

The network ID and join key may be obtained from the Gateway on the Setup >

Network > Settings page on the web server (see Figure 5 on page 7). The

network ID and join key may be changed in the wireless device by using the

following Fast Key sequence.

Table 3 lists the Fast Key sequences for common transmitter functions.

5.0 Power module replacement

Expected black power module life is 10 years at reference conditions.(1)

When module replacement is required perform the following procedure.

1. Remove the cover and module.

2. Replace the module (part number 701PBKKF) and cover.

3. Tighten to specification and verify operation.

5.1 Handling considerations

The black power module with the wireless unit contains two “C” size primary

lithium-thionyl chloride battery (black power module, model number

701PBKKF). Each battery contains approximately 5.0 grams of lithium. Under

normal conditions, the battery materials are self-contained and are not reactive

Table 2. Wireless Configuration Fast Key Sequence

Function Fast Key sequence Menu items

Wireless Configuration 2, 2, 1 Network ID, Join to Network, Broadcast Info

Table 3. Rosemount WDM Special Fast Key Sequence

Function Fast Key sequence Menu items

Device Information 2, 2, 7 Tag, Long Tag, Descriptor, Message, Date

Guided Setup 2, 1 Configure Sensor, Join to Network, Config Advance

Broadcasting, Calibrate Sensor

Manual Setup 2, 2 Wireless, Sensor, Display, HART, Device

Temperature, Device Information, Power, Security

Wireless Configuration 2, 2, 1 Network ID, Join to Network, Broadcast Info

Sensor Configuration 2, 2, 2, 5 Sensor Data Sheet Values, Units, Serial Number

Sensor Calibration 3, 5, 2

Sensor Value, Sensor Status, Current Lower Trim,

Current Upper Trim, Lower Sensor Trim, Upper

Sensor Trim, Device Variable Trim Reset

1. Reference conditions are 70 °F (21° C), transmit rate of once per minute, and routing data for three additional network

devices.

00825-0100-6129_RevAB.fm Page 8 Wednesday, February 13, 2019 3:16 PM

Quick Start Guide

February 2019

as long as the batteries and the pack integrity are maintained. Care should be

taken to prevent thermal, electrical or mechanical damage.

Contacts should be protected to prevent premature discharge.

Black power modules should be stored in a clean and dry area. For maximum

black power module life, storage temperature should not exceed 86 °F (30 °C).

Note

Continuous exposure to ambient temperature limits of -40 °F or 185 °F (-40 °C or 85 °C)

may reduce specified life by less than 20 percent.

Use caution when handling the black power module, it may be damaged if

dropped from heights exceeding 20 feet.

Battery hazards remain when cells are discharged.

5.2 Environmental considerations

As with any battery, local environmental rules and regulations should be

consulted for proper management of spent batteries. If no specific

requirements exist, recycling through a qualified re-cycler is encouraged.

Consult the materials safety data sheet for battery specific information.

5.3 Shipping considerations

The unit was shipped without the black power module installed. Remove the

module prior to shipping the unit.

00825-0100-6129_RevAB.fm Page 9 Wednesday, February 13, 2019 3:16 PM

February 2019

Quick Start Guide

6.0 Product Certifications

Rev 1.0

6.1 European Directive Information

A copy of the EU Declaration of Conformity can be found at the end of the Quick

Start Guide. The most recent revision of the EU Declaration of Conformity can

be found at Emerson.com/Rosemount.

6.2 Telecommunication Compliance

All wireless devices require certification to ensure they adhere to regulations

regarding the use of the RF spectrum. Nearly every country requires this type of

product certification.

Emerson is working with governmental agencies around the world to supply

fully compliant products and remove the risk of violating country directives or

laws governing wireless device usage.

6.3 FCC and IC

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following conditions: This device may not cause harmful interference. This

device must accept any interference received, including interference that may

cause undesired operation. This device must be installed to ensure a minimum

antenna separation distance of 20 cm from all persons.

6.4 Ordinary Location Certification

As standard, the transmitter has been examined and tested to determine that

the design meets the basic electrical, mechanical, and fire protection

requirements by a nationally recognized test laboratory (NRTL) as accredited by

the Federal Occupational Safety and Health Administration (OSHA).

00825-0100-6129_RevAB.fm Page 10 Wednesday, February 13, 2019 3:16 PM

Otros manuales para Rosemount 648

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount 644 Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Rosemount 8732EM Manual de usuario

Emerson

Emerson Rosemount 5600 Series Manual de usuario

Emerson

Emerson Rosemount 4600 Manual de usuario

Emerson

Emerson Rosemount 5300 Series Manual de usuario

Emerson

Emerson Rosemount 5400 Series Manual de usuario

Emerson

Emerson Rosemount 5400 Series Manual de usuario

Emerson

Emerson Incus GDU-01-TT Manual de usuario

Emerson

Emerson Micro Motion Manual de usuario

Emerson

Emerson Rosemount 3051D Manual de usuario

Emerson

Emerson Fisher FIELDVUE 4400 Manual de usuario

Emerson

Emerson Rosemount MultiVariable 4088A Manual de usuario

Emerson

Emerson Rosemount 3051SF Series Manual de usuario

Emerson

Emerson Rosemount 248 Manual de usuario

Emerson

Emerson Rosemount 327T Manual de usuario

Emerson

Emerson Rosemount 3144P Manual de usuario

Emerson

Emerson Rosemount 2051CF series Manual de usuario

Emerson

Emerson Rosemount 644h Manual de usuario

Emerson

Emerson Rosemount 3051HT Manual de usuario

Emerson

Emerson Micro Motion 4700 Manual de usuario

Emerson

Emerson Fisher 4200 Manual de usuario

Emerson

Emerson Rosemount 1152 Alphaline Manual de usuario

Emerson

Emerson Rosemount 8782 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario