Emerson Rosemount 3051 CF Series Manual de usuario
Quick Start Guide
00825-0100-4774, Rev HB
October 2019
Rosemount™ 3051 Pressure Transmitter
and Rosemount 3051CF Series Flow
Meter
with FOUNDATION™ Fieldbus Protocol
Safety messages
Before installing the transmitter, confirm the correct device driver is loaded on the host systems. See
System readiness.
NOTICE
This guide provides basic guidelines for Rosemount™ 3051 Transmitters. It does not provide
instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof,
Flame-Proof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 Reference Manual for
more instructions. This manual is also available electronically on Emerson.com/Rosemount.
WARNING
Explosions
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the local,
national, and international standards, codes, and practices. Review product certifications for any
restrictions associated with a safe installation.
In an explosion-proof/flameproof installation, do not remove the transmitter covers when power
is applied to the unit.
Process leaks
Process leaks may cause harm or result in death.
To avoid process leaks, only use the O-ring designed to seal with the corresponding flange
adapter.
Electrical shock
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Static electricity
Observe safe handling precautions for static-sensitive components.
Conduit/cable entries
Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.
Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all entries
will have the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread
form when closing these entries.
When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands, or
adapters in cable/conduit entries.
Replacement parts
Replacement equipment or spare parts not approved by Emerson for use as spare parts could reduce
the pressure retaining capabilities of the transmitter and may render the instrument dangerous.
Use only bolts supplied or sold by Emerson as spare parts.
Quick Start Guide October 2019
2 Rosemount 3051
WARNING
Improper assembly
Improper assembly of manifolds to traditional flange can damage sensor module.
For safe assembly of manifold to traditional flange, bolts must break back plane of flange web
(i.e., bolt hole) but must not contact sensor module housing.
Severe changes in the electrical loop may inhibit HART® communication or the ability to reach
alarm values. Therefore, Rosemount cannot absolutely warrant or guarantee that the correct
Failure alarm level (High or Low) can be read by the host system at the time of annunciation.
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end
users’ equipment. This could be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your
system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for
all systems used within the facility.
Contents
System readiness......................................................................................................................... 5
Mounting the transmitter.............................................................................................................7
Tagging......................................................................................................................................13
Consider housing rotation..........................................................................................................14
Set the switches......................................................................................................................... 15
Wire, ground, and power up.......................................................................................................17
Configure................................................................................................................................... 20
Zero trim the transmitter........................................................................................................... 28
Product certifications................................................................................................................. 29
October 2019 Quick Start Guide
Quick Start Guide 3
Quick Start Guide October 2019
4 Rosemount 3051
1 System readiness
1.1 Confirm correct device driver
•Verify the correct device driver (DD/DTM™) is loaded on your systems to
ensure proper communications.
•Download the correct device driver at your host vendor download site,
Emerson.com/Rosemount or Fieldbus.org.
Rosemount™ 3051 device revisions and drivers
Table 1-1 provides the information necessary to ensure you have the correct
device driver and documentation for your device.
Table 1-1: Rosemount 3051 FOUNDATION™ Fieldbus Device Revisions and Files
Device
revision(1)
Host Device driver
(DD)(2)
Obtain at Device driver
(DTM)
Manual
document
number
8 All DD4: DD Rev
1
Fieldbus.org Emerson.com 00809-0100-
4774
All DD5: DD Rev
1
Fieldbus.org
Emerson AMS™ Device
Manager V
10.5 or
higher: DD
Rev 2
Emerson.com
Emerson AMS Device
Manager V 8
to 10.5: DD
Rev 1
Emerson.com
Emerson 375/475: DD
Rev 2
Easy Upgrade
Utility
7 All DD4: DD Rev
3
Fieldbus.org Emerson.com 00809-0100-
4774
All DD5: NA N/A
Emerson AMS Device
Manager V
10.5 or
higher: DD
Rev 6
Emerson.com
October 2019 Quick Start Guide
Quick Start Guide 5
Table 1-1: Rosemount 3051 FOUNDATION™ Fieldbus Device Revisions and Files
(continued)
Emerson AMS Device
Manager V 8
to 10.5: DD
Rev 4
Emerson.com
Emerson 375 / 475: DD
Rev 6
Easy Upgrade
Utility
(1) FOUNDATION Fieldbus device revision can be read using a FOUNDATION Fieldbus capable
configuration tool.
(2) Device driver file names use device and DD revision. To access functionality, the correct
device driver must be installed on your control and asset management hosts and on your
configuration tools.
Installation steps
1. Mount the transmitter (Mounting the transmitter).
2. Tag the transmitter (Tagging).
3. Rotate the housing (Consider housing rotation).
4. Set switches and software write lock (Set the switches).
5. Ground, wire, and power up (Wire, ground, and power up).
6. Locate device.
7. Configure (Configure).
8. Zero trim the transmitter (Zero trim the transmitter).
Quick Start Guide October 2019
6 Rosemount 3051
2.1 Mount the transmitter in liquid applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Mount the transmitter so the drain/vent valves are oriented upward.
Figure 2-2: Mounting the Transmitter in Liquid Applications
In-line
2.2 Mount the transmitter in gas applications
Procedure
1. Place taps in the top or side of the line.
2. Mount beside or above the taps.
Figure 2-3: Mounting the Transmitter in Gas Applications
Inline
Quick Start Guide October 2019
8 Rosemount 3051
2.3 Mount the transmitter in steam applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Fill impulse lines with water.
Figure 2-4: Mounting the Transmitter in Steam Applications
In-line
2.4 Install bolts
If the transmitter installation requires assembly of the process flanges,
manifolds, or flange adapters, follow the assembly guidelines to ensure a
tight seal for optimal performance characteristics of the transmitters.
Use only bolts supplied with the transmitter or sold by Emerson™ as spare
parts. Figure 2-5 illustrates common transmitter assemblies with the bolt
length required for proper transmitter assembly.
October 2019 Quick Start Guide
Quick Start Guide 9
Figure 2-5: Common Transmitter Assemblies
B
4 × 2.88-in. (73 mm)
A
4 × 1.75-in. (44 mm)
C
4 ×1.75-in.
(44 mm) 4 ×1.50-in.
(38 mm)
D
4 × 1.75-in. (44 mm)
4 × 2.25-in. (57 mm)
A. Transmitter with coplanar flange
B. Transmitter with coplanar flange and optional flange adapters
C. Transmitter with traditional flange and optional flange adapters
D. Transmitter with coplanar flange and optional manifold and flange
adapters
Bolts are typically carbon steel or stainless steel. Confirm the material by
viewing the markings on the head of the bolt and referencing Table 2-1. If
bolt material is not shown in Table 2-1, contact a local Emerson
representative for more information.
Carbon steel bolts do not require lubrication, and the stainless steel bolts are
coated with a lubricant to ease installation. However, do not apply additional
lubricant when installing either type of bolt.
Table 2-1: Torque Values for the Flange and Flange Adapter Bolts
Bolt material Head markings Initial
torque
Final
torque
Carbon Steel (CS)
B7M
300 in-lb 650 in-lb
Stainless Steel (SST)
316
316
316
SW
316
STM
316
R
B8M
150 in-lb 300 in-lb
Use the following bolt installation procedure:
Quick Start Guide October 2019
10 Rosemount 3051
Otros manuales para Rosemount 3051 CF Series
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Transmisor de Emerson
Emerson
Emerson Rosemount 2051G Manual de usuario
Emerson
Emerson Rosemount 6888A Manual de usuario
Emerson
Emerson Rosemount Analytical Oxymitter 4000 Manual de usuario
Emerson
Emerson Rosemount 3100 Series Manual de usuario
Emerson
Emerson Rosemount 148 Manual de usuario
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Rosemount 2090P Manual de usuario
Emerson
Emerson Fisher 4211 Manual de usuario
Emerson
Emerson Rosemount 1066 Manual de usuario
Emerson
Emerson Rosemount 3051S Series Manual de instrucciones
Emerson
Emerson Rosemount 1208C Manual de usuario
Emerson
Emerson Rosemount 248 Manual de usuario
Emerson
Emerson Micro Motion 5700 Manual de usuario
Emerson
Emerson Rosemount FCL-01 Manual de usuario
Emerson
Emerson Rosemount Oxymitter 4000 Manual de usuario
Emerson
Emerson Rosemount 1056 Manual de usuario
Emerson
Emerson Rosemount 2088 Manual de usuario
Emerson
Emerson Rosemount 8732EM Manual de usuario
Emerson
Emerson Rosemount 1066 Manual de usuario
Emerson
Emerson ROSEMOUNT 5300 Guía de configuración
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
