Emerson Rosemount 2088 Manual de usuario
Quick Start Guide
00825-0100-4108, Rev EA
February 2019
Rosemount™ 2088, 2090F, and 2090P
Pressure Transmitter
with 4–20 mA HART® and 1–5 Vdc Low
Power HART Protocol (Revision 5 and 7)
Safety messages for Rosemount 2088,2090F, and 2090P Transmitters.
NOTICE
This guide provides basic guidelines for Rosemount 2088,2090F, and 2090P Transmitters. It does
not provide instructions for configuration, diagnostics, maintenance, service, troubleshooting,
Explosion-proof, Flameproof, or intrinsically safe(I.S.)installations.
See the Rosemount 2088 Reference Manual for more information. This manual is also available
electronically on Emerson.com/Rosemount.
WARNING
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the appropriate
local, national, and international standards, codes, and practices. Review the approvals section of this
manual for any restrictions associated with a safe installation.
Before connecting a handheld communicator in an explosive atmosphere, make sure the
instruments in the loop are installed in accordance with intrinsically safe or non-incendive field
wiring practices.
In an explosion-proof/flameproof installation, do not remove the transmitter covers when power
is applied to the unit.
Process leaks could result in death or serious injury.
To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.
Electrical shock could cause death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Conduit/cable entries
Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.
Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all entries
will have the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread
form when closing these entries.
Contents
System readiness........................................... 3
Mount the transmitter................................... 6
Set the switches...........................................10
Connect the wiring and power up................ 12
Verify transmitter configuration using a Field
Communicator............................................ 15
Trim the transmitter.................................... 21
Safety Instrumented Systems (SIS) installation
.................................................................... 24
Product certifications...................................25
Rosemount™ 2088 and 2090 Declaration of
Conformity.................................................. 44
China RoHS.................................................. 47
Quick Start Guide February 2019
2 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide
1 System readiness
Confirm HART® revision capability
•If using HART-based control or asset management systems, confirm the
HART capability of those systems prior to transmitter installation. Not all
systems are capable of communicating with HART Revision 7 Protocol.
This transmitter can be configured for either HART Revision 5 or 7.
•For instructions on how to change the HART revision of the transmitter,
see Switch HART Revision mode.
1.1 Confirm correct device driver
•Verify the latest device driver (DD/DTM™) is loaded on your systems to
ensure proper communication.
Note
The Rosemount™ 2088, 2090F, and 2090P Transmitters all use Rosemount
2088 Device Revisions and Drivers.
Procedure
1. Download the latest DD at Emerson.com or FieldCommGroup.org.
2. In the Browse by Member dropdown menu, select Emerson.
3. Select desired product.
a) Reference Table 1-1 and Table 1-2, Find Device Driver Files
column to find the correct device driver.
Table 1-1: Rosemount 2088 and 2090 with 4–20 mA HART Device Revisions and
Files
Release
date
Device identification Device driver
identification
Review
instructions
Review
functionality
NAMUR
revision(1)
HART revision(2) Device
revision(3)
Reference
manual
Change
description(4)
(5)
Hardware Software Universal
Aug-16 1.1.xx 1.0.xx 3 7 10 Rosemount
2088
Reference
Manual
Rosemount
2090
Reference
Manual
(5)
5 9
Jan-13 N/A 1.0.xx 1 7 10 (4)
5 9
February 2019 Quick Start Guide
Quick Start Guide 3
Table 1-1: Rosemount 2088 and 2090 with 4–20 mA HART Device Revisions and
Files (continued)
Release
date
Device identification Device driver
identification
Review
instructions
Review
functionality
NAMUR
revision(1)
HART revision(2) Device
revision(3)
Reference
manual
Change
description(4)
(5)
Hardware Software Universal
Jan-98 N/A N/A 178 5 3 N/A
(1) NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes,
signified above by xx, represent minor product changes as defined per NE53. Compatibility
and functionality are preserved and product can be used interchangeably.
(2) HART® software revision can be read using a HART capable configuration tool. Value shown
is minimum revision that could correspond to NAMUR revisions.
(3) Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed
to enable legacy device driver revisions to continue to communicate with new HART devices.
To access new functionality, the new device driver must be downloaded. It is recommended
to download new device driver files to ensure full functionality.
(4) HART Revision 5 and 7 selectable, Local Operator Interface(LOI), scaled variable,
configurable alarms, expanded engineering units.
(5) Updated electronics hardware design. Intrinsic Safety temperature classification change.
Table 1-2: Rosemount 2088 with 1–5 Vdc Low Power HART Device Revisions and
Files
Release
date
Device identification Device driver
identification
Review
instructions
Review
functionality
NAMUR
revision(1)
HART revision(2) Device
revision(3)
Reference
manual
Change
description(4)
Hardware Software Universal
Jan-13 N/A 1.0.2 3 7 10 Rosemount
2088
Reference
Manual
Rosemount
2090
Reference
Manual
(4)
5 9
Jan-98 N/A N/A 178 5 3 N/A
(1) NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes,
signified above by xx, represent minor product changes as defined per NE53. Compatibility
and functionality are preserved and product can be used interchangeably.
(2) HART software revision can be read using a HART capable configuration tool. Value shown
is minimum revision that could correspond to NAMUR revisions.
(3) Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed
to enable legacy device driver revisions to continue to communicate with new HART devices.
Quick Start Guide February 2019
4 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide
To access new functionality, the new device driver must be downloaded. It is recommended
to download new device driver files to ensure full functionality.
(4) HART Revision 5 and 7 selectable, Local Operator Interface(LOI), scaled variable,
configurable alarms, expanded engineering units.
February 2019 Quick Start Guide
Quick Start Guide 5
2 Mount the transmitter
2.1 Rosemount™ 2088
Mount directly to the impulse line without using an additional mounting
bracket or mount directly to a wall, panel, or two-inch pipe using an optional
mounting bracket.
2.2 Rosemount™ 2090P
Mount directly to the process pipe using an existing weld spud, or have a
skilled welder install a new weld spud using a TIG welder. Refer to Reference
Manual for complete welding instructions. Improper installation may result in
weld spud distortion. Recommended mounting in upright or horizontal
position to allow proper draining of vent.
2.3 Rosemount™ 2090F
Mount directly to the process pipe using a standard sanitary fitting (either a
1.5- or 2-in. Tri Clamp connection). Recommended mounting in upright or
horizontal position to allow proper draining of vent.
Figure 2-1: Transmitter Direct Mounting
Do not apply torque directly to the electronics housing. To avoid damage,
apply torque only to the hex-shaped process connection.
Rosemount
2088
Rosemount 2090P Rosemount
2090F
A. ½–14 NPT female process connection
B. Vessel wall
C. Weld spud
D. O-ring
E. 1½- or 2-in. Tri Clamp connection
Quick Start Guide February 2019
6 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide
Figure 2-2: Panel and Pipe Mounting
Panel mount Pipe mount
2.4 Liquid flow applications
Transmitter mounting procedure for liquid flow applications.
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
Example
2.5 Gas flow applications
Transmitter mounting procedure for gas flow applications.
Procedure
1. Place taps in the top or side of the line.
2. Mount level or above the taps.
February 2019 Quick Start Guide
Quick Start Guide 7
Example
2.6 Steam flow applications
Transmitter mounting procedure for steam flow applications.
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Fill impulse lines with water.
Example
2.7 Environmental seal for housing
Thread sealing (PTFE) tape or paste on male threads of conduit is required to
provide a water/dust tight conduit seal and meets requirements of NEMA®
Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are
required. For M20 threads, install conduit plugs to full thread engagement or
until mechanical resistance is met.
Quick Start Guide February 2019
8 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide
2.8 Gage transmitter orientation
The low side pressure port (atmospheric reference) on the gage transmitters
with aluminum housings are located in the neck of the transmitter, behind the
housing. The vent path is 360° around the transmitter between the housing
and sensor. (See Figure 2-3.)
Keep the vent path free of any obstruction, including but not limited to paint,
dust, and lubrication by mounting the transmitter so that the process can
drain away.
Figure 2-3: Gage Low Side Pressure Port
A
A. Low side pressure port (atmospheric reference)
February 2019 Quick Start Guide
Quick Start Guide 9
3 Set the switches
Set alarm and security switch configuration before installation as shown in
Figure 3-1.
•The alarm switch sets the analog output alarm to high or low. Default
alarm is high.
•The security switch allows ( ) or prevents ( ) any configuration of the
transmitter. Default security is off ( ).
Use the following procedure to change the switch configuration:
Procedure
1. If the transmitter is installed, secure the loop, and remove power.
2. Remove the housing cover opposite the field terminal side. Do not
remove the instrument cover in explosive atmospheres when the
circuit is live.
3. Slide the security and alarm switches into the preferred position using
a small screwdriver.
4. Reattach the transmitter cover. The cover must be fully engaged to
comply with explosion-proof requirements.
Figure 3-1: Transmitter Electronics Board
Without LCD display With LOI/LCD display
A
B
A. Alarm
B. Security
Quick Start Guide February 2019
10 Rosemount™ 2088, 2090F, and 2090P Pressure Transmitter Quick Start Guide
Otros manuales para Rosemount 2088
6
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Transmisor de Emerson
Emerson
Emerson Micro Motion 9739 MVD Guía rápida
Emerson
Emerson wirelessHART Rosemount Series Manual de usuario
Emerson
Emerson Rosemount 3051 Series Manual de usuario
Emerson
Emerson Micro Motion 2400S Manual de usuario
Emerson
Emerson Rosemount 3051S Series Guía de configuración
Emerson
Emerson Rosemount 4088B MultiVariable Manual de usuario
Emerson
Emerson Micro Motion 1000 Series Guía rápida
Emerson
Emerson Rosemount 2051 Manual de usuario
Emerson
Emerson Rosemount 644h Manual de usuario
Emerson
Emerson Fisher FIELDVUE 4400 Manual de usuario
Emerson
Emerson Rosemount 3095FB MultiVariable MODBUS Manual de usuario
Emerson
Emerson MICRO MOTION 1500 Manual de usuario
Emerson
Emerson Micro Motion 5700 Manual de usuario
Emerson
Emerson Rosemount 3051S ERS Manual de usuario
Emerson
Emerson Micro Motion 9739 MVD Guía rápida
Emerson
Emerson Rosemount 6888A Manual de usuario
Emerson
Emerson Rosemount 644 Manual de usuario
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Rosemount 4088B MultiVariable Manual de usuario
Emerson
Emerson Rosemount 644h Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
