Emerson Rosemount 5408 Manual de usuario
Quick Start Guide
00825-0500-4408, Rev AA
October 2017
Rosemount™5408 and 5408:SIS Level
Transmitters
Process Seal Antenna
October 2017
2
Quick Start Guide
1.0 About this guide
This Quick Start Guide provides basic guidelines for the Rosemount 5408 and
5408:SIS Level Transmitters.
Refer to the Rosemount 5408 and 5408:SIS Reference Manual for more
instructions. The manual and this guide are also available electronically on
Emerson.com/Rosemount.
Failure to follow safe installation and service guidelines could result in death or serious injury.
Make sure the transmitter is installed by qualified personnel and in accordance with applicable code of
practice.
Use the equipment only as specified in this guide and the Rosemount 5408 and 5408:SIS Reference Manual.
For installations in hazardous locations, the transmitter must be installed according to the Rosemount 5408
and 5408:SIS Product Certifications document and System Control Drawing (D7000002-885).
Repair, e.g. substitution of components etc. may jeopardize safety and is under no circumstances allowed.
Explosions could result in death or serious injury.
Verify that the operating environment of the transmitter is consistent with the appropriate hazardous
locations certifications.
Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in the
loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.
Do not remove the transmitter covers in explosive atmospheres when the circuit is alive.
Both transmitter covers must be fully engaged to meet explosion-proof requirements.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause
electrical shock.
Make sure the main power to the transmitter is off and the lines to any other external power source are
disconnected or not powered while wiring the transmitter.
Process leaks could result in death or serious injury.
Make sure that the transmitter is handled carefully. If the process seal is damaged, gas might escape from
the tank.
Hot surfaces
The flange and process seal may be hot at high process temperatures.
Allow to cool before servicing.
Quick Start Guide
3
October 2017
2.0 Confirm approval type
For hazardous locations transmitters labeled with multiple approval types:
Permanently mark the checkbox of the selected approval type(s).
Contents
Confirm approval type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Align transmitter head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
Adjust display orientation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Prepare the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11
Connect wiring and power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Configure transmitter using Guided Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
October 2017
4
Quick Start Guide
3.0 Mount the transmitter
3.1 Installation procedure
Flanged version
Tri Clamp version
page 5
page 7
Quick Start Guide
5
October 2017
3.2 Flanged version
Step 1: Lower the transmitter into the nozzle
Note
Be careful not to scratch or otherwise damage the PTFE sealing.
PTFE sealing
October 2017
6
Quick Start Guide
Step 2: Tighten the bolts and nuts
Note
Re-tighten after 24 hours and again after the first temperature cycle.
Check at regular intervals and re-tighten if necessary.
Step 3: Align the transmitter head (see page 8)
Table 1. Torque Value, lb-ft (N-m)(1)(2)
1. The conditions used for the calculation are: Standard mating metal flange, A193 B8M Cl.2 / A4-70
bolt material, and a friction coefficient of μ=0.16.
2. Low strength bolt and non-metallic mating flange may require lower tightening torque.
Process
connection size
Process connection rating
ASME B16.5 EN1092-1 JIS B2220
Class 150 Class 300 PN6 PN10/PN16 PN25/PN40 10K
2-in./DN50/50A 29 (40) 52 (70) 15 (20) 26 (35) 29 (40) 18 (25)
3-in./DN80/80A 33 (45) 48 (65) 37 (50) 37 (50) 41 (55) 22 (30)
4-in./DN100/100A 59 (80) 52 (70) 37 (50) 37 (50) 74 (100) 26 (35)
Quick Start Guide
7
October 2017
3.3 Tri Clamp version
Step 1: Lower the transmitter into the nozzle
Note
Be careful not to scratch or otherwise damage the PTFE sealing.
Step 2: Tighten the clamp
Tighten the clamp to the recommended torque (see the manufacturer’s
instruction manual).
Step 3: Align the transmitter head (see page 8)
PTFE sealing
October 2017
8
Quick Start Guide
4.0 Align transmitter head
Open tank
Align the marking on sensor module toward the tank wall.
Still pipe
Align the external ground screw toward the holes of the still pipe.
Chamber
Align the external ground screw toward the process connections.
Quick Start Guide
9
October 2017
Step 1: Loosen the nut slightly and turn the transmitter
Step 2: Verify transmitter is properly aligned
See page 8 for direction.
Step 3: Tighten the nut
Torque 355 in-lb (40 N-m)
60 mm
October 2017
10
Quick Start Guide
5.0 Adjust display orientation (optional)
To improve field access to wiring or to better view the optional LCD display:
1. Loosen the set screw until the transmitter housing can rotate smoothly.
2. First, rotate the housing clockwise to the desired location. If the desired
location cannot be achieved due to thread limit, rotate the housing
counterclockwise to the desired location (up to 360° from thread limit).
3. Re-tighten the set screw.
Figure 1. Rotate the Transmitter Housing
H3/32 in.
Torque 30 in-lb (3 N-m)
Otros manuales para Rosemount 5408
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Transmisor de Emerson
Emerson
Emerson Micro Motion 5700 Guía rápida
Emerson
Emerson Rosemount 248 Manual de usuario
Emerson
Emerson Rosemount 6888A Manual de usuario
Emerson
Emerson Micro Motion 5700 Manual de usuario
Emerson
Emerson Rosemount 3051HT Manual de usuario
Emerson
Emerson Rosemount 8712EM Manual de usuario
Emerson
Emerson Rosemount 3101 Manual de usuario
Emerson
Emerson Rosemount TCL Manual de usuario
Emerson
Emerson Rosemount 3051 Series Manual de usuario
Emerson
Emerson Rosemount 2051HT Manual de usuario
Emerson
Emerson Rosemount ET210 Manual de usuario
Emerson
Emerson Rosemount 3095FC MultiVariable Manual de usuario
Emerson
Emerson Rosemount ET410 Manual de usuario
Emerson
Emerson Rosemount 248 Manual de usuario
Emerson
Emerson Rosemount Analytical Oxymitter 4000 Manual de usuario
Emerson
Emerson Oxymitter 5000 Manual de usuario
Emerson
Emerson Rosemount 3095 Manual de usuario
Emerson
Emerson Rosemount 2051 Wireless Series Manual de usuario
Emerson
Emerson Rosemount 848T Manual de usuario
Emerson
Emerson MICRO MOTION 2700 Guía rápida
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
