Emerson Rosemount ET410 Manual de usuario
Quick Start Guide
MS-00825-0100-4209, Rev AA
April2023
Rosemount™ Wireless ET410
Corrosion Transmitter
with Rosemount Permasense™
technology
Safety messages
Failure to follow these installation guidelines could result in death or serious injury. Only
qualified personnel should perform the installation.
WARNING
Explosion hazard that could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review the
approvals section of this manual for any restrictions associated with a safe installation.
Before connecting a CC21 to a sensor, ensure the correct low voltage permits have been
obtained
The power module may be replaced in a hazardous area. Only fit Permasense or Rosemount
approved BP20E power modules.
Magnetic hazard that can result in death or serious injury
This device contains magnets which could be harmful to pacemaker wearers.
The strong magnets used in the magnetic fixture can lead to serious hand injuries unless
personnel are careful.
Electrostatic hazard that can result in death or serious injury
The power module has surface resistivity greater than one gigaohm and must be properly
installed on the wireless device. Care must be taken during transportation to and from the
point of installation to prevent a potential electrostatic charging hazard.
The transmitter’s polymer enclosure has surface resistivity greater than one gigaohm. Care
must be taken during transportation to and from the point of installation to prevent a
potential electrostatic charging hazard.
NOTICE
Shipping considerations for wireless products.
The unit was shipped to you without the power module installed. Remove the power module
prior to any re-shipping.
Each device contains two “D” size primary lithium-thionyl chloride battery cells. Primary
lithium batteries are regulated in transportation by the U.S. Department of Transportation,
and are also covered by IATA (International Air Transport Association), ICAO (International
Civil Aviation Organization), and ARD (European Ground Transportation of Dangerous
Goods). It is the responsibility of the shipper to ensure compliance with these or any other
local requirements. Consult current regulations and requirements before shipping.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or
misconfiguration of end users’ equipment. This could be intentional or unintentional and
needs to be protected against.
Physical security is an important part of any security program and fundamental in protecting
your system. Restrict physical access by unauthorized personnel to protect end users’ assets.
This is true for all systems used within the facility.
Quick Start Guide April2023
2 Emerson.com/Rosemount
Contents
Product overview......................................................................................................................... 5
Preparing for installation............................................................................................................ 8
Mounting the transmitter with a strap................................................................................... 10
Mounting the transmitter with a magnetic fixture................................................................24
Maintenance...............................................................................................................................36
Product certifications................................................................................................................ 41
April2023 Quick Start Guide
Quick Start Guide 3
Quick Start Guide April2023
4 Emerson.com/Rosemount
1 Product overview
A. Antenna
B. Power module
C. Head
D. Strap slot
E. Foot
April2023 Quick Start Guide
Quick Start Guide 5
1.1 What's in the box
Mounting hardware option T01(1) Mounting hardware option B02(2)
Permasense ET410 Sensor (with protective cap)
BP20E Power module
A4 Stainless Steel Strap 138 in (3.5 m) Magnetic mount
Strap tensioner Brackets and fittings (already fitted
to sensor)
Lanyard kit 6.6 ft (2 m) 316 stainless
steel lanyard with looped end and
cable lock.
5 x Lanyard kit (for safety-securing
sensor and magnetic fixture).
(1) Pipe strap up to 40-inch diameter pipe and one strap tensioner.
(2) Magnetic mount, vessel mount
1.2 Required equipment
In order to install the sensor, you need the following equipment from
an IK220 installation kit
•Tablet PC with installation application software
•CC21 interface
WARNING
The tablet PC is not intrinsically safe.
A site-specific permit may be required for its use.
Quick Start Guide April2023
6 Emerson.com/Rosemount
1.3 Required tooling
Separate tooling for Strap option
Tooling is supplied in the IK220 installation kit.
•Tin snips (used to cut the fixing strap to the correct length)
•Flathead screwdriver or wrench and socket (to tighten the fixing
strap)
•2.5 mm hex key (for power module retaining bolts)
Tooling required for magnetic fixture
•Torque wrench with 13mm A/F deep socket
•13mm A/F spanner
•6mm A/F hex key
•2.5mm hex key (for the power module retaining bolts)
1.4 Alternative installation options
Optional tooling
If preferred, an electric screwdriver or wrench may be used instead
of the supplied tools to decrease installation time. This is not
included in IK220 installation kit
April2023 Quick Start Guide
Quick Start Guide 7
2 Preparing for installation
Prerequisites
The Emerson Wireless Gateway should be installed and functioning
properly before commissioning the Rosemount ET410 and powering
it with a BP20E power module.
Note
Wireless devices should be powered up in order of proximity
from the Gateway, beginning with the closest device, then working
outward from the Gateway. This results in a simpler and faster
network formation. Enable Active Advertising on the Gateway to
ensure new devices are able to join the network faster. For more
information, see the Emerson Wireless 1410S Gateway.
Procedure
1. Identify the location where the sensor is to be installed.
2. Ensure that all cladding and insulation is removed around the
circumference of the pipe at the sensor location.
The dimension drawing in Figure 2-1 provides guidance on
how much pipe should be exposed.
Note
Cladding or insulation can be replaced after the sensor
installation is completed, provided that the head of the sensor
remains outside of the insulation. Insulation materials can be
installed around the sensor as desired and according to local
procedures.
Quick Start Guide April2023
8 Emerson.com/Rosemount
Figure 2-1: Transmitter dimensions
Note
Dimensions are in millimeters [Inches].
3. Clean the area where the sensor will touch the pipe to
remove any particles that might keep the transducer away
from the pipe surface or damage the face of the transducer. A
permanent marker may be used to show exactly where each
sensor is to be placed on the pipe.
April2023 Quick Start Guide
Quick Start Guide 9
3 Mounting the transmitter with a strap
3.1 Mounting the transmitter
If you are using the strap mounting option, perform the tasks in this
section.
If you are using the magnetic fixture, skip this section and go to the
Mounting the transmitter with a magnetic fixture.
WARNING
Two people are required for this operation
Personal protective equipment (PPE) of gloves and safety glasses
or full-face visor are recommended.
Cut strap may have sharp edges.
Do not cut the strap while it is under tension because this action
can result in damage or injury.
Procedure
1. Unbox the strap tensioner and the strap from the packaging.
2. Feed the strap into one end of the strap tensioner and using
the screwdriver or wrench and socket provided, turn the screw
on the tensioner until the end of the strap emerges from
under the worm drive (at least 5 turns of the worm-screw are
required).
3. Remove the protective cap from the sensor.
CAUTION
Once the protective cap is removed, the strong magnetic field
at the end of the sensor can suddenly attract other objects,
such as tools. This can cause injury as well as damage to the
sensor.
Only remove the protective cap when necessary and then take
great care. Ensure tools and fastenings are kept away from the
sensor when the cap is removed.
4. Carefully place the sensor on the required location on the
pipe.
5. Check the sensor is on the location correctly and the
thermocouple is in contact with the surface.
Quick Start Guide April2023
10 Emerson.com/Rosemount
Otros manuales para Rosemount ET410
1
Tabla de contenidos
Otros manuales de Transmisor de Emerson
Emerson
Emerson Rosemount 3051S Series Manual de usuario
Emerson
Emerson Rosemount 56 Manual de usuario
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Micro-Motion 2400S Guía rápida
Emerson
Emerson Micro Motion 4200 Manual de usuario
Emerson
Emerson Rosemount 3051G Manual de usuario
Emerson
Emerson Rosemount 248 Manual de usuario
Emerson
Emerson Rosemount 708 Manual de usuario
Emerson
Emerson Micro Motion 5700 Manual de usuario
Emerson
Emerson Micro Motion 2400S Guía rápida
Emerson
Emerson Micro Motion Transmitters and Discrete Controllers Series... Manual operacional
Emerson
Emerson Rosemount 326P Manual de usuario
Emerson
Emerson Fisher 4200 Manual de usuario
Emerson
Emerson Rosemount 1408A Manual de usuario
Emerson
Emerson Rosemount 8732E Manual de usuario
Emerson
Emerson Fisher 4211 Manual de usuario
Emerson
Emerson MicroMotion FOUNDATION 5700 Manual de usuario
Emerson
Emerson Rosemount 2240S Manual de usuario
Emerson
Emerson Micro Motion 4700 Manual de usuario
Emerson
Emerson Rosemount 248 Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
