Emerson OSE Series Manual de usuario

Type OSE

Instruction Manual

D103687X012

November 2015

SLAM-SHUT VALVE

CONTENTS

Introduction ........................................................................ 1

Characteristics ................................................................... 1

Labelling ............................................................................. 2

Dimensions and Weights ................................................... 3

Operation ........................................................................... 4

Installation .......................................................................... 4

Commissioning .................................................................. 5

Maintenance ...................................................................... 6

Spare Parts ........................................................................ 7

Figure 1. Type OSE Slam-Shut Valve

The OSE is in conformity with the

Pressure Equipment Directif PED 97/23/CE

and is classiﬁed under category IV.

CHARACTERISTICS

Material

Body Steel

Bonnet Steel

Oriﬁce Stainless steel

Valve plug Stainless steel

O-rings Nitrile

Connections

Inlet/Outlet: ISO PN 100 B (ANSI 600 RF)

ISO PN 50 B (ANSI 300 RF)

ISO PN 20 B (ANSI 150 RF)

Other connections available

(contact factory)

ISO PN 16 B, 25 B, 40 B

Impulse (IS): 1/4’’ NPT threaded

Mechanism box vent (E): 1/4” NPT threaded

Impulse diameter: Tube interior Ø 8/10 mm

Safety contact: See D103683X012 manual

INTRODUCTION

Scope of Manual

This manual provides installation, start-up, maintenance,

and parts ordering information for the Type OSE Slam-

Shut Valve.

Information on other equipment used with this slam-shut

valve is found in separate manuals.

Product Description

The OSE Slam-Shut Valve protects transmission and

distribution networks or pipe lines supplying industries and

commercial businesses.

It permits the gas ﬂow to be cut off rapidly and totally in the

case of under or over regulator pressure.

The OSE exists in DN 25 (1”) to DN 150 (6”). DN 200 (8”)

and DN 250 (10”) are covered by the OSE LS.

The OSE consists of:

• A body with a removable oriﬁce, enclosed by a bonnet

• A valve plug with integral bypass, tightshut by an O-ring

• A release relay type OS2 including:

- A mechanism box (BM)

- A safety manometric box (BMS) to be connected on

the outlet side of the pressure regulator.

Type OSE

LABELLING

- 20 / + 60 °C (bolting class 8-8)

- 30 / + 71 °C (boltingA320L7)

CLAPET DE SECURITE

SLAM-SHUT VALVE

DN 25

505 2110 4670 7860 14850

50 80 100 150

PN 40 B

20 B1 50 J 50 B1 100 J 100 B2

25 B 16 B 20 J

Class

2 (bolting class 8-8)

- (boltingA320L7)

Temperature TS

Pumax

Other connections available (contact factory)

Security Class

BMS setting

Max only

Min only All BMS

types

DD MM YEAR

C60

(1) BMS : Safety manometric box

(2) Differential strength (depending on BMS chosen)

(3) Temperature depending on bolting material (see label)

Table 1. Technical Characteristics of the Type OSE Slam-Shut Valve

DN 25 50 80 100 150 Bypass

Cg 505 2110 4670 7860 14850 25

C1 35 35 35 32 33 35

ΔP max (bar) > 25 > 25 25 10 6 100

Relay travel (mm) 35 35 50 50 50

C50

Table 2. Flow Coefﬁcient, ΔP max, Relay travel

Figure 2. Label for Type OSE Slam-Shut Valve

OPERATING PRESSURE

Body, valve plug PS 100 bar maxi

Associated BMS(1) according to size PSD 10 à 100 bar

Maximum Inlet Pressure Pumax 100 bar

Type DS Differential strength(2)

OPERATING TEMPERATURE(3) TS - 20 / 60 °C

- 30 / 71 °C

SLAM-SHUT

Sizes available DN 25, 50, 80, 100, 150

Norm EN 14382

Operating class A or B (see label, ﬁgure 2)

Accuracy AG 2,5 – 5 (Piston)

Setpoint range

Wdu-Wdo

0,010 à 100 bar

Response time ta < 1 s

Max Differential (valve closed)

∆P max

100 bar

Max Differential (valve open)

∆P max

Voir tableau 2

Rearming Manually after rectiﬁcation of fault

Position indicator On mechanism box

FLUID

Group 1 and 2 according to PED 97/23/CE, 1st and 2nd family gas according

to EN 437, or other gases (compressed air, nitrogen).

The gas must be noncorrosive, clean (ﬁltration on inlet side necessary) and dry

Type OSE

DIMENSIONS AND WEIGHTS

C52

BC max

Figure 3. Type OSE Slam-Shut Valve Dimensions

Other PN16/25/40: contact factory

DN PN (B) ANSI (RF)

DIMENSIONS

WEIGHT (kg)

A B C Max D E

20 150 185 54 334 220 116 14

50 300 197 62 334 220 124 16

100 600 210 62 334 220 124 17

20 150 254 76 346 220 152 26

50 300 267 83 346 220 165 29

100 600 287 83 346 220 165 32

20 150 298 95 380 220 190 43

50 300 318 105 380 220 210 48

100 600 337 105 380 220 210 55

100

20 150 353 114 420 220 229 74

50 300 368 127 420 220 154 82

100 600 394 137 420 220 273 98

150

20 150 451 140 424 220 357 150

50 300 473 159 424 220 357 166

100 600 508 178 424 220 357 202

C53

Table 3. Type OSE Slam-Shut Valve Dimensions and Weights

Type OSE

OPERATION

The pressure of the zone to be protected (generally the pipe

line on the outlet side of the pressure regulator and situated

after the slam shut valve) activates the safety manometric

box BMS.

If pressure rises above the release set point the release

relay frees the valve plug (key 7).

Through the action of the weight of the valve plug, the

closing spring and the ﬂuid (attempting to close), the valve

plug will seat into the oriﬁce (key 6).

The gas ﬂow is obstructed until the mechanism box is

manually rearmed.

To reopen the valve plug an equal pressure balance on inlet

and outlet sides is required.

The mechanism box is rearmed after opening the internal

bypass (key 1).

Rearming and balancing are achieved at the same time.

INSTALLATION

AVERTISSEMENTS

All interventions on the equipment should

only be performed by qualiﬁed and

trained personnel.

C51

Figure 4. Type OSE LS - Principle of Operation

The slam shut valve is installed on the

inlet side of the regulator, on the horizontal

pipeline. The mechanism box should be

situated on top (see above schematic) or on

top for versions DN 25-50-80.

Installation according to EN12186 is recommended.

Install according to direction of the ﬂuid ﬂow

(see arrow).

When assembling with adjacent elements,

care must be taken not to create pressure

force on the body and the assembling

elements (bolts, O-rings, ﬂanges) should be

compatible with the geometry and working

conditions of the equipment.

If the case arises a support must be used to

avoid pressure force on the body (a support

can be installed under the ﬂanges).

Connect the safety manometric box (IS) to

the impulse at 4D on the outlet pipe.

It is recommended to install an isolation

valve (R1) and an atmospheric valve (R2), which

can be useful for tripping and veriﬁcations.

No modiﬁcation should be made to the

structure of the equipment (drilling, grinding,

soldering ...).

Verify that the inlet side is protected by an

appropriate device(s) to avoid exceeding the

limits of utilization (PS, TS).

Type OSE

Safety contact: see D103683X012 manual

C54

Pu Pd

REGULATOR D

4 D

Figure 5. Type OSE Slam-Shut Valve Installation Schematic

Verify that the limits of utilization correspond

to the appropriate operating conditions.

Verify that the safety manometric box (BMS)

and spring correspond to the appropriate

operating conditions on the outlet side of the

regulator.

The equipment should not receive any type

of shock, especially the release relay.

The user should verify or carry out a

protection adapted to the environment.

Fire, seismic and lightening are not taken

into consideration for standard regulators.

If required, a special product selection and/

or speciﬁc calculations may be supplied

according to speciﬁc requirements.

If the slam-shut is classiﬁed under operating

class B the

BMS diaphragm should be

checked periodically.

COMMISSIONING

WARNING

All interventions on the equipment should

only be performed by qualiﬁed and

trained personnel.

Preliminary veriﬁcations

Start-up positions

• Inlet and outlet valves

→Closed

Verify absence of pressure between inlet and outlet valves

• Slam-shut valve plug

→Closed

• Impulse isolation valve

→Closed

• Impulse atmospheric valve

→Open

Setpoint Veriﬁcation

Using the atmospheric valve, inject a pressure equal to the

pressure foreseen for the regulator

• 1st release relay stage

→Set (Stage 1)

TRIGGERED POSITION

TRAVEL

STOP

TRAVEL

STOP

TRAVEL

STOP

C59

Figure 6. Setpoint Veriﬁcation

STAGES 2 & 3STAGE 1

• Slam shut valve

→Open (Stages 2 & 3)

→Progressively increase the pressure to reach tripping

→Adjust setting if necessary (D103683X012 manual)

Note the set point value on the equipment or mark it in a

commissioning document.

Positions before Commissioning

• Impulse isolation valve

→Open

• Impulse atmospheric valve

→Closed

• Slam shut valve plug

→Closed

The equipment is ready for commissioning

Type OSE

C57

Figure 7. Type OSE - Commissioning Schematic

Commissioning (max. only or max. & min.)

• Inlet valve

→Open slowly

• Slam-shut bypass

→Open slowly (stage 2)

• Regulator

→Put into operation (see corresponding manual)

• 1st release relay stage

→Set (Stage 1)

• Slam shut valve plug

→Open (Stage 3)

• Outlet valve

→Open slowly

The equipment is commissioned

After checking and commissioning the release relay it is

recommended to seal it

MAINTENANCE

Servicing Check

Recommended frequency:

• Twice yearly minimum

Veriﬁcation:

• Tripping and tripping value

• Slam-shut tightness

Departure positions

• Inlet valve →Open

• Outlet valve →Open

• Slam-shut →Open

• Regulator →In operation

Inlet and outlet sides of regulator under pressure

Tripping veriﬁcation

• Inlet valve →Closed

• Outlet valve →Closed

• Regulator Increase setpoint to reach tripping

(without exceeding the outlet limits)

Disassembly

Recommended frequency:

• Every 4 to 6 years (or less depending on operating

conditions)

• In the case of BMS 162 or 071, it is highly recommended to

check the condition of the diaphragm once yearly

Veriﬁcation:

• Condition of O-rings, diaphragm, and lubrication

Replacement:

• O-rings, diaphragm

Tools:

• Spanners 10, 13, six-sided wrench 6

• Spanners According to DN size

• Francel spanner ref. 197125 (bypass and pin disassembly)

• Valve plug closed

• Close inlet and outlet valves

• Bleed off outlet pressure

• Bleed off inlet pressure

• Unscrew impulse connection IS

• Remove BM cover (key 8)

• Unscrew fastening screw (key 9)

• Remove cap

• Remove BM

• Unscrew screws (key 10)

• Remove bonnet (key 11)

• Remove spring (rep. 12) and slam-shut valve plug

(key 13)

• Unscrew bypass (key 1)

• Unscrew screws (key 14) (DN 100 and 150)

The removal of the oriﬁce (not recommended) requires a

special extraction tool

Reassembly

• Perform the above operations in reverse order (respect

tightening torques)

• Replace O-rings at each disassembly

• The valve plug should be maintained in an upright position

using the packing gland to facilitate it’s removal

Type OSE

• Precaution should be taken when removing or replacing

the valve plug to avoid damaging the segments

• Lubricate screws before tightening

• Lubricate O-rings (silicone grease) except for the valve

plug O-ring

• Lightly lubricate the stem (silicone grease)

• Lubricate the release relay mechanism (yoke and bolt)

(molybdenum graphite grease)

• Lubricate the BMS spring (molybdenum graphite grease)

A special tool is required when installing a new oriﬁce

Table 7. Troubleshooting for Type OSE Slam-Shut Valve

Table 5. Torques for Connecting Part Screw

(key 10, Fig. 7)

DN Dimensions Spanner (inches) Torque

(N.m)

25 9/16-12 X1 3/4 13/16’’ 110

50 1/2-13 X1 1/2 3/4’’ 110

80 5/8-11 X1 3/4 15/16’’ 175

100 3/4-10 X2 1/4 1’’1/8 260

150 1-8 X2 3/4 1’’1/2 510

C58a

Table 6. Torques for Bypass (key 1. Fig. 7)

DN Torque (N.m)

25 14

50 14

80 20

100 24

150 24

C58b

C58c

Key Torque (N.m)

915

Table 4. Torques (key 9 & 14, Fig. 7)

SYMPTOMS CAUSE ACTIONS

If the valve will not close Operating fault

Check the release relay

Check the valve plug

or contact after-sales

If the valve closes Operating correctly Observe the evolution of the outlet pressure

(check tightness)

If the outlet pressure in the slam shut is

decreases External leak Locate and seal the leak

or contact after-sales

If the outlet pressure in the slam shut is

constant

Bleed off the outlet side of the regulator

Observe the evolution of the outlet pressure

(check tightness)

If the outlet pressure increases Internal leak

Check the slam shut valve plug

Check the oriﬁce

Check the bypass

or contact after-sales

Key Description DN 25 DN 50 DN 80 DN 100 DN 150

1 Bypasse 180977

2 Valve plug O-ring 400257 400263 400258 400260 400261

3 Segments 401950 401951 401952 401953 401954

4 O-ring 400298 400295 400297 400296 19B0359X12

5 O-ring 400009 400024 400259 400045 400262

Packing gland “Kit” 197395

Set of O-rings* 197447 197448 197449 197450 197451

Spare parts kit** 197452 197453 197454 197455 197456

Release Relay Type OS2 See D103683X012 manual

(*) Set of O-rings and segments including O-rings key 2, 3, 4, 5 (**) Spare-parts kit including set of O-rings, bypass (key 1) and bypass disassembly spanner

Table 8. Spare Parts for Type OSE Slam-Shut Valve

SPARE PARTS

Type OSE

The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners.

Francel is a mark of Francel SAS, a business of Emerson

Process Management.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees,

express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or speciﬁcations of such products at any

time without notice.

Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson Process

Management product remains solely with the purchaser.

Industrial Regulators

Emerson Process Management

Regulator Technologies, Inc.

USA - Headquarters

McKinney, Texas 75070, USA

Tel: +1 800 558 5853

Outside U.S. +1 972 548 3574

Asia-Paciﬁc

Shanghai 201206, China

Tel: +86 21 2892 9000

Europe

Bologna 40013, Italy

Tel: +39 051 419 0611

Middle East and Africa

Dubai, United Arab Emirates

Tel: +971 4811 8100

For further information visit www.emersonprocess.com/regulators

Natural Gas Technologies

Emerson Process Management

Regulator Technologies, Inc.

USA - Headquarters

McKinney, Texas 75070, USA

Tel: +1 800 558 5853

Outside U.S. +1 972 548 3574

Asia-Paciﬁc

Singapore 128461, Singapore

Tel: +65 6777 8337

Europe

O.M.T. Tartarini s.r.l. Via P. Fabbri 1,

I-40013 Castel Maggiore (Bologna), Italy

Tel: +39 051 419 0611

Francel SAS, 3 ave Victor Hugo,

CS 80125 - Chartres 28008, France

Tel: +33 2 37 33 47 00

Middle East and Africa

Dubai, United Arab Emirates

Tel: +971 4811 8100

TESCOM

Emerson Process Management

Tescom Corporation

USA - Headquarters

Elk River, Minnesota 55330-2445, USA

Tels: +1 763 241 3238

+1 800 447 1250

Asia-Paciﬁc

Shangai 201206, China

Tel: +86 21 2892 9499

Europe

Selmsdorf 23923, Germany

Tel: +49 38823 31 287

O.M.T. Ofﬁcina Meccanica Tartarini S.R.L., R.E.A 184221 BO Cod. Fisc. 00623720372 Part. IVA 00519501209 N° IVA CEE IT 00519501209,

Cap. Soc. 1.548 000 Euro i.v. R.I. 00623720372 - M BO 020330

Francel SAS, SIRET 552 068 637 00057 APE 2651B, N° TVA : FR84552068637, RCS Chartres B 552 068 637, SAS capital 534 400 Euro

BMS

C56

Figure 8. Type OSE Spare Parts

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson SM-I/O 24V Protected Manual de usuario

Emerson

Emerson ANDERSON GREENWOOD 96A Series Manual

Emerson

Emerson Sempell series Manual de usuario

Emerson

Emerson EXD-U02 Manual de usuario

Emerson

Emerson PACSystems RX3i IC695ECM850 Manual de usuario

Emerson

Emerson COMX-430 Manual de usuario

Emerson

Emerson Fisher Type H800 Manual de usuario

Emerson

Emerson VA001-102-01 Guía

Emerson

Emerson EX4-6-...FLR Series Manual de usuario

Emerson

Emerson 63EG Manual de usuario

Emerson

Emerson OMB Manual de usuario

Emerson

Emerson Fisher POSI-SEAL A81 Manual de usuario

Emerson

Emerson TARTARINI BM9 Manual de usuario

Emerson

Emerson Anderson Greenwood 93 Series Manual de usuario

Emerson

Emerson ALCO CONTROLS FSE-0 Manual de usuario

Emerson

Emerson Fisher D4 Manual de usuario

Emerson

Emerson Fisher OSE Manual de usuario

Emerson

Emerson XC1008D Diagrama de cableado

Emerson

Emerson fisher EDR Manual de usuario

Emerson

Emerson IEC 62591 Manual de usuario

Emerson

Emerson EIM PCU REV A4 Manual

Emerson

Emerson Fisher G101 Series Manual de usuario

Emerson

Emerson Fisher NPS 2 CCV-N Manual de usuario

Emerson

Emerson Fisher ME00124272 Guía de configuración

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario