Emerson KEYSTONE F635 Instrucciones de instalación

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson Spence K3 Manual de usuario

Emerson

Emerson CROSBY HE ISOFLEX Series Guía

Emerson

Emerson KEYSTONE OPTISEAL F16 Manual de usuario

Emerson

Emerson PACSystems RX3i Manual de usuario

Emerson

Emerson Fisher Baumann 24000S Manual de usuario

Emerson

Emerson Keystone 990 Documento técnico

Emerson

Emerson ANDERSON GREENWOOD PILOT 9300 Series Manual de usuario

Emerson

Emerson C471 Manual de usuario

Emerson

Emerson Fisher NPS 2 CCV-N Manual de usuario

Emerson

Emerson Daniel 762 Manual de usuario

Emerson

Emerson Fisher Baumann 87000 Manual de usuario

Emerson

Emerson Keystone Figure 952 Manual de usuario

Emerson

Emerson numatics E22 Manual de usuario

Emerson

Emerson Alco Controls TIH FLR Series Manual de usuario

Emerson

Emerson IEC 62591 Manual de usuario

Emerson

Emerson FM-3 Manual de usuario

Emerson

Emerson YARWAY B Manual

Emerson

Emerson FISHER 66R Manual de usuario

Emerson

Emerson SM-EZMotion Module P/N 400361-00 Manual de usuario

Emerson

Emerson Fisher Control-Disk NPS 14 CL150 Manual de usuario

Emerson

Emerson Crosby JOS-E Series Manual de usuario

Emerson

Emerson White-Rodgers 36C01 Manual de usuario

Emerson

Emerson FISHER LR128 Series Manual de usuario

Emerson

Emerson ANDERSON GREENWOOD MARVAC 121 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

3

12

11

5

6

7

1

8

9

10

2

4

KEYSTONE SLURRY CONTROL VALVES

FIGURE 635

Complete assembly and disassembly instructions for F635 slurry valves

DISASSEMBLY INSTRUCTIONS

1. Remove the valve from the pipeline. The disc should be in the closed position.

2. Disconnect any electric or pneumatic lines and remove the actuator.

3. Clean off all external deposits of slurry by steam cleaning or grit blasting.

4. Remove both gland nuts (12), gland plate (5) and gland collar (6).

5. Remove both gland studs (11) from the valve body (1).

6. Remove the end cover plate (9) and gasket(8).

7. Remove the disc screws (4). For valve sizes DN 50 - 300, there are two only disc screws.

For sizes DN 350 - 500, there are three. With the larger valves it is recommended that you

support the disc.

8. Drive out the shaft (3) using a brass or aluminium dolly from the bottom of the valve.

9. Remove the disc (2).

10. Remove all the old gland packing (7).

11. Thoroughly clean all components and examine them for excessive wear or damage, replacing

them where necessary.

12. Disassembly is now complete and ready for re-assembly. Refer to assembly instructions.

NOTE: DN 50 - 300 valve illustrated.

ASSEMBLY INSTRUCTIONS

1. Fit the graphite gasket (8) to the end cover(9).

2 Fit the end cover (8, 9, 10) to the bottom end of the valve body (1).

3 Pack the valve gland with graphite packing(7).

4 Fit both gland studs (11) after first coating them with anti-seize compound.

5 Fit the disc (2) inside the valve bore, with the disc screw holes uppermost. (For 5 degree angled

seat option only, ensure that the disc is positioned so that the valve will close in the anti-clock

wise direction, looking from the top of the valve.)

6 Fit the gland plate (5) and the gland collar (6) to the shaft (3).

7 Insert the shaft assembly (3, 5 and 6) through the body (1) and disc (2), ensuring that the shaft

and disc screw holes are aligned.

8 Fit and tighten the disc screws (4). For valve sizes DN 50 - 300, there are two only disc screws

for sizes DN 350 - 500, there are three.

9 Check that the disc is free to rotate. (For 5 degree angled seat options, check that the disc is

free to move from the open to the 5 degree closed position).

10. Tighten up the gland nuts (12) ensuring it is not overtightened.

11. Assembly is now complete and ready for installation. Refer to the F635 installation and

commissioning instructions.

12. The gland may need to be adjusted on plant start up.

© 2012 Emerson plc. All Rights Reserved.www.valves.emerson.com VCIOM-02909-EN 15/09

© 2017 Emerson. All rights reserved.