Emerson Fisher FLOBOSS 407 Manual de usuario

Field Automation Systems

Loose-leaf version: Part Number D301080X012

Bound version: Contact FAS

FLOBOSS™ 407 FLOW MANAGER

Instruction Manual

Form A6013

May 2000

FloBoss 407 Instruction Manual

ii Rev 5/00

Revision Tracking Sheet

May 2000

This manual may be revised periodically to incorporate new or updated information. The date revision

level of each page is indicated at the bottom of the page opposite the page number. A major change in

the content of the manual also changes the date of the manual which appears on the front cover. Listed

below is the date revision level of each page.

Page Revision

All 5/00

Previous Editions:

November 1998 - Added changes for 1.05/1.06 firmware and added references to ROCLINK.

FloBoss is a trademark of Fisher Controls International, Inc.

HART is a registered trademark of the HART Communication Foundation.

Printed in the U.S.A.

While this information is presented in good faith and believed to be accurate, Fisher Controls does not guarantee satisfactory results from

reliance upon such information. Nothing contained herein is to be construed as a warranty or guarantee, express or implied, regarding the

performance, merchantability, fitness or any other matter with respect to the products, nor as a recommendation to use any product or

process in conflict with any patent. Fisher Controls reserves the right, without notice, to alter or improve the designs or specifications of the

products described herein.

FloBoss 407 Instruction Manual

Rev 5/00 iii

Table of Contents

(For a more detailed listing, see the Section Contents at the front of each section.)

SECTION 1 — GENERAL INFORMATION............................................................1-1

1.1 Scope of Manual...............................................................................................................................1-1

1.2 Section Contents...............................................................................................................................1-2

1.3 Product Overview.............................................................................................................................1-2

1.4 Installation Guidelines......................................................................................................................1-5

1.5 Power Consumption Calculation......................................................................................................1-9

1.6 Startup and Operation.....................................................................................................................1-13

1.7 Keypad Operation...........................................................................................................................1-14

1.8 Service Bulletins.............................................................................................................................1-15

SECTION 2 — THE FLOBOSS 407 BASE UNIT .....................................................2-1

2.1 Scope..................................................................................................................................................2-1

2.2 Product Description............................................................................................................................2-2

2.3 Installation........................................................................................................................................2-11

2.4 Connecting the FloBoss 407 to Wiring............................................................................................2-14

2.5 Troubleshooting and Repair.............................................................................................................2-19

2.6 Specifications...................................................................................................................................2-32

SECTION 3 — INPUT/OUTPUT MODULES ...........................................................3-1

3.1 Scope.................................................................................................................................................3-1

3.2 Product Descriptions.........................................................................................................................3-2

3.3 Initial Installation and Setup.............................................................................................................3-7

3.4 Connecting the I/O Modules to Wiring............................................................................................3-8

3.5 Troubleshooting and Repair ...........................................................................................................3-29

3.6 Removal, Addition, and Replacement Procedures .........................................................................3-37

3.7 I/O Module Specifications..............................................................................................................3-40

FloBoss 407 Instruction Manual

Table of Contents (Continued)

iv Rev 5/00

SECTION 4 — COMMUNICATIONS CARDS.........................................................4-1

4.1 Scope.................................................................................................................................................4-1

4.2 Product Descriptions.........................................................................................................................4-1

4.3 Initial Installation and Setup.............................................................................................................4-8

4.4 Connecting Communication Cards to Wiring ................................................................................4-11

4.5 Troubleshooting and Repair ...........................................................................................................4-18

4.6 Communications Card Specifications.............................................................................................4-20

SECTION 5 — DISPLAY AND KEYPAD..................................................................5-1

5.1 Scope.................................................................................................................................................5-1

5.2 Product Description..........................................................................................................................5-1

5.3 Keypad Functions.............................................................................................................................5-4

5.4 Display of Parameters.......................................................................................................................5-9

5.5 Security...........................................................................................................................................5-17

5.6 Troubleshooting and Repair ...........................................................................................................5-18

APPENDIX A — LIGHTNING PROTECTION MODULE....................................A-1

A.1 Scope................................................................................................................................................A-1

A.2 Product Description .........................................................................................................................A-1

A.3 Initial Installation.............................................................................................................................A-2

A.4 Connecting the LPM to Wiring .......................................................................................................A-3

A.5 Troubleshooting and Repair ............................................................................................................A-4

A.6 Specifications...................................................................................................................................A-4

APPENDIX B — MULTI-VARIABLE SENSORS....................................................B-1

B.1 Scope................................................................................................................................................B-1

B.2 Description....................................................................................................................................... B-1

B.3 MVS Mounting................................................................................................................................B-3

FloBoss 407 Instruction Manual

Table of Contents (Continued)

Rev 5/00 v

B.4 Field Wiring..................................................................................................................................... B-7

B.5 Configuration.................................................................................................................................B-13

B.6 Calibration ..................................................................................................................................... B-14

B.7 MVS Troubleshooting and Repair................................................................................................. B-18

B.8 Specifications................................................................................................................................. B-19

APPENDIX C — I/O SIMULATION .........................................................................C-1

C.1 Scope................................................................................................................................................C-1

C.2 Analog Outputs to Analog Inputs....................................................................................................C-1

C.3 Analog Outputs to a meter...............................................................................................................C-2

C.4 Discrete Outputs to Discrete Inputs................................................................................................. C-3

C.5 Discrete Outputs to Pulse Inputs......................................................................................................C-4

C.6 Potentiometer to Analog Inputs.......................................................................................................C-5

C.7 Switch to Discrete Inputs.................................................................................................................C-6

C.8 Switch to Pulse Inputs .....................................................................................................................C-7

GLOSSARY OF TERMS.............................................................................................G-1

INDEX ..............................................................................................................................I-1

FloBoss 407 Instruction Manual

vi Rev 5/00

[This page is intentionally left blank.]

FloBoss 407 Instruction Manual

Rev 5/00 1-1

SECTION 1 — GENERAL INFORMATION

1.1 SCOPE OF MANUAL

This manual describes the FloBoss™407 Flow Manager (also called the ROC407), part of the family of

FloBoss Flow Managers manufactured by Fisher Controls. Both the Standard version and the

Measurement Canada version of the FloBoss 407 are covered in this manual. Included are the

following sections:

♦Section 1 General Information

♦Section 2 FloBoss 407 Base Unit

♦Section 3 Input/Output Modules

♦Section 4 Communications Cards

♦Section 5 Display and Keypad

♦Appendix A Lightning Protection Module

♦Appendix B Multi-Variable Sensors

♦Appendix C I/O Simulation

♦Glossary Glossary of Terms

♦Index Topical Index

Section 1 describes this and related manuals. Section 1 also provides a summary of the FloBoss 407

hardware, installation guidelines, and information on power consumption, startup, and keypad

operation.

Section 2 provides information and specifications concerning the two main components of the FloBoss

407, the processor board and the termination board.

Section 3 provides information and specifications for the optional I/O modules available for the FloBoss

407.

Section 4 provides information and specifications for the communications card options available for the

FloBoss 407.

Section 5 describes the operation of the keypad and the display.

Appendix A describes the optional lightning protection module.

Appendix B describes the Multi-Variable Sensors available for the FloBoss 407.

Appendix C shows various ways to set up I/O simulation for troubleshooting I/O components and

configurations.

FloBoss 407 Instruction Manual

1-2 Rev 5/00

1.2 SECTION CONTENTS

This section contains the following information:

Information Section Page Number

Product Overview 1.3 1-2

Related Documents and Compatibility 1.3.1 1-4

Installation Guidelines 1.4 1-5

Environmental Requirements 1.4.1 1-5

Site Requirements 1.4.2 1-5

Compliance with Hazardous Area Standards 1.4.3 1-6

Power Installation Requirements 1.4.4 1-7

Grounding Installation Requirements 1.4.5 1-7

I/O Wiring 1.4.6 1-8

Power Consumption Calculation 1.5 1-9

Determining I/O Channel Power Consumption 1.5.1 1-9

Determining Radio Power Consumption 1.5.2 1-12

Totaling Power Requirements 1.5.3 1-12

Startup and Operation 1.6 1-13

Startup 1.6.1 1-13

Operation 1.6.2 1-13

Keypad Operation 1.7 1-14

Service Bulletins 1.8 1-15

1.3 PRODUCT OVERVIEW

The FloBoss 407 is a microprocessor-based flow computer (see Figure 1-1) that provides functions

required for gas flow measurement and custody transfer in accordance with standards such as AGA

1985 or 1992 orifice metering. More generally, the unit provides on-site functionality for applications

where there is a need for remote monitoring, measurement, data archival, communications, and control.

The design allows the user to configure the FloBoss 407 for specific applications including those

requiring calculations, logic, and sequencing control using function sequence tables, as well as PID

loop control.

The FloBoss 407 is available in two versions based on the type of approval: the standard hazardous

area version, and the Measurement (Industry) Canada custody transfer version, which includes

hazardous area approval. These versions have a number of differences both in firmware and hardware.

Both of these versions are further subdivided by the type of orifice metering calculations (either AGA

1992 or AGA 1985) included in the firmware.

FloBoss 407 Instruction Manual

Rev 5/00 1-3

Figure 1-1. FloBoss 407 Flow Manager

Physically, the FloBoss 407 consists of two printed circuit cards, a keypad, and a display housed in a

compact weather-tight case. The printed circuit cards are the processor board and the termination

board.

Built into the termination board are two analog input (AI) channels. Moving a jumper on the

termination board changes one of the built-in analog inputs to a pulse input (PI). The pulse input can be

wired either as a FloBoss-powered or a device-powered, medium-speed pulse counter. The pulse

circuitry is optically coupled to isolate the termination board from the input signal.

In addition, the termination board has slots for four plug-in input/output (I/O) modules (also called

modular I/O). The plug-in I/O modules allow any combination of discrete inputs, discrete outputs,

analog inputs, analog outputs, or pulse inputs an application requires.

NOTE

I/O modules must not be used as flow inputs for Industry Canada approved

FloBoss 407 units.

The built-in Liquid Crystal Display (LCD) and membrane keypad provide the ability to look at data and

configuration parameters while on site. The keypad also permits limited editing of parameter values.

The FloBoss 407 can have up to four Multi-Variable Sensor (MVS) devices connected to it. The MVS

provides the differential pressure, static pressure, and temperature inputs needed for performing orifice

flow calculations. As many as four MVS devices (one of which can be an integral MVS) can be used

with a FloBoss 407. The integral MVS is factory-mounted to the bottom of the enclosure with a

coupler and further secured with a stiffening plate. For detailed information on the MVS, refer to

Appendix B.

FloBoss 407 Instruction Manual

1-4 Rev 5/00

The FloBoss has two communication ports built in: a local operator interface port and an EIA-232

serial port. A variety of optional plug-in communication cards are available that allow you to add

another communications channel: EIA-232 serial, EIA-422/485 serial, dial-up modem, radio modem,

or leased-line modem communications.

The FloBoss 407 is packaged in a NEMA 4X windowed enclosure that can mount on a wall or a

pipestand. The enclosure, which protects the electronics from physical damage and harsh environ-

ments, is fabricated of die-cast, low-copper aluminum alloy. It consists of four pieces: the body, the

electronics cover, the keypad cover, and the lower cover. Silicone-rubber gaskets seal the unit when the

covers are closed. All covers are secured by captive screws.

Note that for the Measurement Canada version of the FloBoss 407, the electronics cover, and the lower

cover are secured by special captive screws. These screws have holes through the heads for adding

security wire seals according to Measurement (Industry) Canada requirements.

For the standard version of the FloBoss 407, an optional padlock adapter can be added in the field. This

adapter is installed on the captive screw that secures the electronics cover. With the shank (up to 0.25

inch diameter) of the padlock running through the adapter, the screw is inaccessible and the cover

cannot be opened. Refer to Section 2.3 for adapter installation instructions.

The FloBoss 407 unit can be mounted either on a wall or on a 2-inch pipestand (U-bolt mounting kit is

supplied). For installation information, refer to Section 1.4 and Section 2.3.

Configuration of the FloBoss 407, including installing user programs (special versions may be needed

for the Measurement Canada FloBoss), requires a personal computer and ROCLINK Configuration

Software. See Section 1.3.1 for compatible configuration software and its documentation.

For a more details about the FloBoss 407, refer to Section 2.

1.3.1 Related Documents and Compatibility

For software aspects such as configuration, refer to the following manual:

♦Type RL101 ROCLINK Configuration Software User Manual (Form A6051) – ROCLINK

Version 2.1 or greater is required for all Measurement Canada FloBoss 407 units as well as

standard FloBoss units with Version 1.05 firmware or greater. ROCLINK Version 2.1 also

works with standard FloBoss units that have an earlier version of firmware. ROCLINK

Version 2.0 can be used for standard FloBoss units with Version 1.04 or earlier firmware.

For FST information, refer to the following manual:

♦Function Sequence Table User Manual (Form A4625) – Provides information on setting up

an FST to run in the FloBoss, including how to use the FST Editor supplied with the

configuration software.

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson Fisher EZ easy-e Manual de usuario

Emerson

Emerson Fisher A11 Manual de usuario

Emerson

Emerson KGA Manual de usuario

Emerson

Emerson E2 Manual de usuario

Emerson

Emerson White Rodgers 36H Series Manual de usuario

Emerson

Emerson Fisher V500 Manual de usuario

Emerson

Emerson Crosby J Series Manual de usuario

Emerson

Emerson KTM Series Manual de usuario

Emerson

Emerson EXD-U02 Manual de usuario

Emerson

Emerson SW46 Manual de usuario

Emerson

Emerson Fisher H200 Series Manual de usuario

Emerson

Emerson Alco Controls TIH FLR Series Manual de usuario

Emerson

Emerson Fisher Design GX Series Manual de usuario

Emerson

Emerson KEYSTONE F635 Instrucciones de instalación

Emerson

Emerson KTM Series Guía rápida

Emerson

Emerson SEMPELL Manual de usuario

Emerson

Emerson Neotecha Sapro Guía de configuración

Emerson

Emerson Fisher POSI-SEAL A81 Manual de usuario

Emerson

Emerson RAIMONDI Manual de usuario

Emerson

Emerson 91 Manual de usuario

Emerson

Emerson Dixell XEC Supercap Diagrama de cableado

Emerson

Emerson Heated Flame Ionization Detector Module Model NGA 2000... Manual de usuario

Emerson

Emerson Alco Controls TIH Series Manual de usuario

Emerson

Emerson Tartarini PRX Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario