Emerson Fisher H200 Series Manual de usuario
Figure 1. H200 Series Relief Valve
H200 Series External Relief Valves
▲ WARNING
Failure to follow these instructions or
to properly install and maintain this
equipment could result in an explosion,
fire and/or fire causing property damage
and personal injury or death.
Fisher™ relief valves must be installed,
operated and maintained in accordance
with federal, state and local codes, rules
and regulations and Emerson Process
Management Regulator Technologies Inc.
(Emerson) instructions.
A person should never stand directly
over or in front of or look directly into a
relief valve when the tank is pressurized.
The relief valve could suddenly “pop”
open blowing gas, dirt and other debris
into the person’s face and eyes.
Call a qualified service person to service
the unit. Installation, operation and
maintenance procedures performed
by unqualified person may result
in improper adjustment and unsafe
operation. Either condition may result in
equipment damage or personal injury.
Only a qualified person shall install or
service the relief valve.
Introduction
Scope of the Manual
This manual provides specications, installation,
maintenance instructions and parts ordering
information for the H200 Series.
Only personnel qualied through training or experience
should install, operate and maintain this relief valve. If
there are any questions concerning these instructions,
contact your local Emerson Impact Partner Oce
before proceeding.
Product Description
The H200 Series Pop™ relief valves, Figures 1 and 2,
are self-operated relief valves with preset and pinned
spring retainers. The inlet pressure registers directly
on a spring opposed poppet assembly which includes
a Nitrile (NBR) disk. When the inlet gas pressure
increases above the spring setting, the poppet and disk
assembly is pushed away from the orifice. Springs
are available that provide any relief pressure setting
from 25 to 300 psig / 1.7 to 20.7 bar.
With this simple operation and wide spring setting
selection, the H200 Series Pop relief valves
may be used where venting to atmosphere is
acceptable, where the process gas is compatible
with the Nitrile (NBR) disk, where its relief capacity
is adequate and where some pressure relieving
tolerance is acceptable. Common applications
include use on pneumatic control lines of air drills,
jackhammers and other similar equipment and on
farm tap installations. The H200 Series is comprised
of the Types H202 and H203 relief valves with the
dierence being in the inlet connection size.
Instruction Manual
D104657X012
August 2023
H200 Series
Specifications
This section lists the specications for H200 Series external relief valves. Factory specications are engraved on
the body of the relief valve at the factory.
Available Configuration and End Connections
Type H202: 3/4 NPT connection
Type H203: 1 NPT connection
Maximum Allowable Relief (Inlet) Pressure(1)
400 psig / 27.6 bar
Relief Pressure Ranges(1)
See Tables 1 and 2
Flow Capacity
See Table 2
Construction Materials
Body, Poppet and Spring Retainer: Brass
Disk: Nitrile (NBR)
Spring: 302 Stainless steel
Temperature Capabilities(1)
-20 to 160°F / -29 to 71°C
Approximate Weight
0.5 lbs / 0.2 kg
Option
Type P145 raincap
1. The pressure/temperature limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.
Table 1. Relief Pressure Spring Ranges
RELIEF PRESSURE SETTINGS SPRING
PART NUMBER SPRING COLOR RELIEF SETTING TOLERANCE
psig bar psig bar
25 to 30 1.7 to 2.1 1H485637022 Pink ±5 ±0.34
31 to 55 2.1 to 3.8 1J152137022 White
56 to 70 3.9 to 4.8 1P391137022 Blue
±8 ±0.5565 to 95 4.5 to 6.5 T1049037022 Plain
90 to 130 6.2 to 9.0 1F791337022 Purple
131 to 160 9.0 to 11.0 1F7912T0012 Yellow
±15 ±1.03
161 to 190 11.1 to 13.1 T12699T0012 Green
191 to 235 13.2 to 16.2 1F790937022 Brown
236 to 300 16.3 to 20.7 1E954637052 Plain
Table 2. Relief Set Pressures and Capacities
RELIEF SET PRESSURE(1) SET PRESSURE PLUS BUILD-UP FLOW CAPACITY(2)
psig bar psig bar SCFH Nm3/h
25 1.7 50 3.4 34,200 916
50 3.4 75 5.2 47,400 1270
75 5.2 100 6.9 60,000 1608
100 6.9 120 8.3 69,600 1865
125 8.6 150 10.3 83,400 2235
150 10.3 180 12.4 100,500 2693
175 12.1 210 14.5 117,600 3152
200 13.8 240 16.5 132,000 3538
225 15.5 270 18.6 150,000 4020
250 17.2 300 20.7 165,000 4422
275 19.0 330 22.7 180,000 4824
300 20.7 360 24.8 195,000 5226
1. This is the initial leak point, the point at which the relief valve begins to discharge.
2. 0.6 Specific Gravity Gas. To convert to equivalent capacities of other gases, multiply the table values by 0.775 for air or 0.789 for nitrogen. Multiply the flow obtained by 0.0268 to convert
to (Nm3/h) at 0°C and 1.01 bar.
2
H200 Series
Figure 2. H200 Series Operational Schematics
W0120_1
Principle of Operation
The relief valve (See Figure 1) is held close by the
spring force seating the rubber valve disc against
the orifice.
When the tank pressure exceeds the spring force, the
valve disc lifts off the orifice allowing gas to discharge
through the valve to the air.
Gas discharge initially may be small producing only
seepage and a light “hissing” sound. As pressure
increases and gas volume discharge continues, a
“popping” condition occurs with large volumes of gas
discharge and a loud “hissing or roaring” sound.
When the tank pressure decreases enough, the
spring force closes the valve disc back against the
orifice stopping further discharge
Installation
▲ WARNING
Vapor relief valves must be installed
only in the vapor space to provide relief
capacity for the tank.
This relief valve may be installed in any position but
must be oriented so that gas discharged from the
valve does not create a re, toxic or explosion hazard.
The relief valve should be protected from material and
conditions that could clog the outlet side of the valve
and aect the venting of gas.
A typical installation is shown in Figure 3. A Type P145
raincap is recommended for use with any H200 Series
relief valve.
The relief valve and installation should be checked for
compliance with all applicable codes.
Maintenance
Safety relief valves are non-repairable valves and
cannot be adjusted in the field.
▲ WARNING
Any valve that has fully opened “popped”
should be tested to see if it is within the
allowable start-to-discharge pressure
setting. If it is not within the correct
range, it must be replaced. Relief
valve start-to-discharge and reseat
pressures may be lower if the valve has
fully opened (popped).
It is recommended that all relief valves be regularly
inspected for visible damage, dirt, corrosion, missing
raincaps, paint inside outlet, tampering, etc. If any of
the preceding is evident or questionable, the valve
should be re-tested or replaced immediately.
The discharge side of the relief valve body must be
kept free of dirt, water and other foreign matter which
can damage the valve seat or “weld” some “wing style”
poppets to the valve body. This can prevent the valve
from opening. Replace valves when this occurs.
H200 SERIES
RELIEF VALVE
TYPE P145 RAIN CAP
LOW-PRESSURE
REDUCING REGULATOR
HIGH-
PRESSURE
REDUCING
REGULATOR
INLET PRESSURE
Figure 3. Typical Farm Tap Installation
AF9930-C
A1619-1
3
H200 Series
D104657X012 © 2023 Emerson Process Management Regulator
Technologies, Inc. All rights reserved. 08/23.
The Emerson logo is a trademark and service mark of Emerson Electric
Co. All other marks are the property of their prospective owners.
Fisher™ is a mark owned by Fisher Controls International LLC, a business
of Emerson Automation Solutions.
The contents of this publication are presented for informational purposes
only, and while every eort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their use
or applicability. All sales are governed by our terms and conditions, which
are available upon request. We reserve the right to modify or improve the
designs or specications of such products at any time without notice.
Emerson Process Management Regulator Technologies, Inc does not
assume responsibility for the selection, use or maintenance of any
product. Responsibility for proper selection, use and maintenance of any
Emerson Process Management Regulator Technologies, Inc. product
remains solely with the purchaser.
Parts Ordering
When corresponding with your local Sales Office
about this relief valve, include the type number,
serial number and other information stamped on
the nameplate.
When ordering replacement parts, reference the key
number of each needed part and specify the eleven
character part number as found in the following
parts list.
Parts List
Key Description Part Number
1 Body
2 Spring Retainer
3 Groove Pin
4* Spring
5 Poppet Assembly
H200 Series
Facebook.com/EmersonAutomationSolutions
LinkedIn.com/company/emerson-automation-solutions
Twitter.com/emr_automation
Fisher.com
Emerson Automation Solutions
Americas
McKinney, Texas 75070 USA
T +1 800 558 5853
+1 972 548 3574
Europe
Bologna 40013, Italy
T +39 051 419 0611
Asia Pacic
Singapore 128461, Singapore
T +65 6777 8211
Middle East and Africa
Dubai, United Arab Emirates
T +971 4 811 8100
Otros manuales de Unidad de control de Emerson
Emerson
Emerson Fisher 161 Series Manual de usuario
Emerson
Emerson Baumann 51000 Series Manual de usuario
Emerson
Emerson ASCO 290 Series Manual de usuario
Emerson
Emerson Sempell PSRV VS99 Manual de usuario
Emerson
Emerson EIM PCU REV A4 Manual
Emerson
Emerson ALCO CONTROLS FSE-0 Manual de usuario
Emerson
Emerson YARWA 151 Series Manual de usuario
Emerson
Emerson PACSystems VersaMax IC200CMM020 Manual de usuario
Emerson
Emerson KEYSTONE DUBEX Manual de usuario
Emerson
Emerson Yarway 9200 Series Manual de usuario
Emerson
Emerson Spence K3 Manual de usuario
Emerson
Emerson Rosemount Ultrasonic 3410 Series Manual de usuario
Emerson
Emerson Copeland 3290262 Manual
Emerson
Emerson Rosemount RM5800 Manual de usuario
Emerson
Emerson ALCO CONTROLS FSE-0 Manual de usuario
Emerson
Emerson Fisher 6060 Manual de usuario
Emerson
Emerson E2 Manual de usuario
Emerson
Emerson Anderson Greenwood 93 Series Manual de usuario
Emerson
Emerson ES-805 Series Manual de usuario
Emerson
Emerson FISHER LR128 Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
