Emerson Fisher Baumann 26000 Manual de usuario

www.Fisher.com

Baumann™26000 Corrosion Resistant

Control Valve

Contents

Introduction 1...................................

Scope of Manual 1.............................

Safety Precautions 2...........................

Maintenance 3.................................

Installation 3..................................

Air Piping 4...................................

Packing Adjustments 4.........................

Disassembly 4................................

Reassembly and Calibration 5...................

Parts Ordering 7................................

Dimensions and Weights 9.......................

Figure 1. Baumann 26000 Control Valve

W9766

26000 Control Valve with

Baumann 32 Actuator

and Dual Travel Stops

26000 Valve with Baumann 32

Actuator, Dual Travel Stops, and

FIELDVUEtDVC6200 Digital

Valve Controller

X0663

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for the Baumann 26000 corrosion

resistant control valve.

Do not install, operate, or maintain Baumann 26000 control valves without being fully trained and qualified in valve,

actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is

important to carefully read, understand, and follow all the contents of this manual, including all safety cautions and

warnings. If you have any questions about these instructions, contact your Emerson sales office or Local Business

Partner before proceeding.

Description

The Baumann 26000 Corrosion Resistant Control Valve (figure 1) features a flangeless wafer valve body. The 316

stainless steel flangeless body and thru-hole wafer design allows for installation between plastic pipeline flanges

without risk of gasket leakage. This same valve body, fully pressurized, retains an all wetted PTFE interior resulting in a

solid mechanical structure.

Instruction Manual

D103363X012

26000 Valve

June 2017

Instruction Manual

D103363X012

26000 Valve

June 2017

Educational Services

For information on available courses for the Baumann 26000 valve, as well as a variety of other products, contact:

Emerson Automation Solutions

Educational Services - Registration

Phone: 1-641-754-3771 or 1-800-338-8158

E-mail: [email protected]

emerson.com/fishervalvetraining

Safety Precautions

WARNING

Always wear protective gloves, clothing and eyewear when performing any installation operations to avoid personal

injury.

Personal injury or property damage caused by sudden release of pressure or bursting of pressure retaining parts may result

if service conditions exceed those for which the product was intended. To avoid injury or damage, provide a relief valve for

over pressure protection as required by government or accepted industry codes and good engineering practices.

Check with your process or safety engineer for any additional measures that must be taken to protect against process

media.

If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this

instruction manual.

CAUTION

This valve is intended for a specific range of pressures, temperatures and other application specifications. Applying

different pressures and temperatures to the valve could result in parts damage, malfunction of the control valve or loss of

control of the process. Do not expose this product to service conditions or variables other than those for which the product

was intended. If you are not sure what these conditions are you should contact your Emerson sales office or Local Business

Partner for more complete specifications. Provide the product serial numbers (shown on the nameplate) and all other

pertinent information.

WARNING

If you move or work on an actuator installed on a valve with loading pressure applied, keep your hands and tools away

from the stem travel path to avoid personal injury. Be especially careful when removing the stem connector to release all

loading on the actuator stem whether it be from air pressure on the diaphragm or compression in the actuator springs.

Likewise take similar care when adjusting or removing any optional travel stop. Refer to the relevant actuator Maintenance

Instructions.

If hoisting the valve, take care to prevent people from being injured in case the hoist or rigging slips. Be sure to use

adequate sized hoists and chains or slings to handle the valve.

WARNING

Personal injury could result from packing leakage. Valve packing is tightened before shipment; however, the packing

might require some readjustment to meet specific service conditions.

Instruction Manual

D103363X012

26000 Valve

June 2017

Maintenance

WARNING

Avoid personal injury and property damage from sudden release of process pressure or bursting of parts. Before

performing any maintenance operations:

D Do not remove the actuator from the valve while the valve is still pressurized.

D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations.

D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the

actuator cannot suddenly open or close the valve.

D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure

on both sides of the valve. Drain the process media from both sides of the valve.

D Depending on the actuator construction, it will be necessary to manage the pneumatic actuator spring

pre-compression. It is essential to refer to the relevant actuator instructions in this manual to perform safe removal of

the actuator from the valve.

D Use lock‐out procedures to be sure the above measures stay in effect while you work on the equipment.

D The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the

pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when

loosening the packing box pipe plug.

D Check with your process or safety engineer for any additional measures that must be taken to protect against process

media.

Note

Whenever a gasket seal is disturbed by removing or shifting gasketed parts, install a new gasket during reassembly. This provides a

good gasket seal because the used gasket may not seal properly.

WARNING

Avoid personal injury or property damage by thoroughly cleaning the line of all dirt, welding chips, scale, oil or grease, and

other foreign material. Failure to do so could result in parts damage, malfunction of the control valve or loss of control of

the process.

To avoid personal injury or property damage, do not attempt to do any work on a valve while the system is in operation,

the valve must be isolated 100% from the active system and the isolated line voided of pressure and/or hazardous fluids.

Installation

1. Before installing the valve in the pipeline, thoroughly clean the line of all dirt, welding chips, scale, oil or grease, and

other foreign material.

2. Install the valve so the controlled fluid will flow through the valve body in the direction indicated by the arrow cast on

the valve body.

3. A three-valve bypass must be used to permit removal of the control valve from the line without shutting down the

system.

4. In case of a heat-insulated installation, insulate the valve body only, not the bonnet.

Instruction Manual

D103363X012

26000 Valve

June 2017

CAUTION

The PTFE valve body insert protrudes slightly beyond both sides of the valve body (key 1); it is highly recommended that

the included PTFE encapsulated line flange adapter gaskets (key 21) be utilized. (Refer to figures 3, 2, and 4).

Air Piping

1. For an air-to-extend actuator (air-to-close action), connect the actuating air pressure line to the 1/4 NPT opening in

the upper diaphragm case. For an air-to-retract actuator (air-to-open action) connect the actuating air pressure line

to the 1/4 NPT in the lower diaphragm case.

2. Use 6.4 mm (1/4 inch) O.D. tubing or equivalent for all air lines. If air line exceeds 8 m (25 ft) in length, 9.5 mm (3/8

inch) tubing is preferred. Air lines must not leak. Air pressure not to exceed 2.5 bar (35 psig).

Packing Adjustments

(Refer to figures 3, 2, and 4)

Should seat leakage or leakage by the bonnet (key 8) occur, try to retighten the internal packing (key 17) by

disconnecting the air line to the actuator, loosen the hex clamp nut (key 12) and turn the bonnet (key 8) clockwise into

the valve body (key 1). This rotation will compress the packing (key 17) around the plug and stem assembly (key 4) and

against the valve body interior. Retighten the hex clamp nut (key 12) and recheck for leakage.

Should the valve stem packing (key 14) need to be adjusted, turn the packing follower (key 10) clockwise to tighten or

counterclockwise to loosen.

Disassembly

Significant wear or contamination may require replacement of the plug or seals. Proceed as follows:

1. Loosen the yoke clamp nut (key 9) and disconnect the actuator (see appropriate actuator instructions).

2. Loosen the packing follower (key 10) and the hex clamp nut (key 12).

3. Unscrew and remove the bonnet (key 8) from the valve body (key 1).

4. Remove the packing (key 17) from the valve body (key 1) by flowing air into port A. This will drive the V-ring packing

seals and plug out of the top opening of the valve body.

CAUTION

The PTFE valve body insert protrudes slightly beyond both sides of the valve body (key 1); it is highly recommended that

the included PTFE encapsulated line flange adapter gaskets (key 21) be utilized.

Instruction Manual

D103363X012

26000 Valve

June 2017

Reassembly and Calibration

1. Lay out all parts and clean the valve body thoroughly.

2. Hold the valve body (key 1) upside down, see figure 5.

3. Insert the lower (half round) packing ring.

Note

The flat side should rest in the bottom of the housing bore.

4. Insert the first packing V-ring with the V opening facing the lower ring. Tip the ring slightly to prevent the ring from

hanging up at the corner of the outlet port, see figure 5.

5. For Cv < 1.0, insert a spacer ring (key 3) with the V opening towards first packing ring. Note: The cross hole must line

up with the hole B in a radial direction and within 1/16 inch in the vertical direction. The spacer ring (key 3) is not

required in Cv = 2.5 or Cv = 4.2.

6. Insert the remainder of the packing V-rings (key 17) as shown, one at a time. Tip each ring slightly to ease

installation.

7. Move the valve body (key 1) right-side up and clamp in a vise or test fixture, using the line flange adapter gaskets

(key 21).

8. Screw the hex clamp nut (key 12) all the way onto the lower thread of the bonnet (key 8).

9. Screw the bonnet seal (key 50) all the way onto the lower thread of the bonnet (key 8) until it touches the nut (key

12).

10. Lubricate the lower bonnet thread with anti-seize lubricant and insert the valve plug and stem assembly (key 4) into

the bonnet (key 8).

11. Screw the bonnet (key 8) with the plug and stem assembly (key 4) loosely into the valve body (key 1).

12. Push the stem all the way down until the plug is fully seated.

13. Install the valve body in the test fixture or between a pair of appropriate mating line flanges.

14. Apply 50 psi air pressure to the fixture or the flange connected to valve port A and connect port B to a flow meter or

bubble indicator (tube in water).

15. For Cv < 1.0, slowly screw the bonnet (key 8) into the valve body with a 1-1/4 inch wrench until the air flow stops

completely. Push the valve stem up and down several times and repeat the leakage test. For Cv > 1.0, screw the

bonnet (key 8) down until it touches the packing and then turn an additional 180 degrees.

Note

The force to pull up or push down the stem should not exceed 25 lbs.

16. Close off air flow leaving port B and pull up the stem. This will pressurize all parts of the valve body.

17. Apply leak detection fluid or soap solution to the thread between the valve body and bonnet (key 8). There should

be no leakage.

18. Hold the bonnet in place and tighten the nut (key 12) firmly (this will compress the bonnet seal (key 50).

19. Install the secondary packing kit [packing spring (key 6), washer (key 16), stem packing rings (key 14), packing

spacer (key 20) and packing follower (key 10)] into the bonnet as shown in figure 6. Tighten by rotating the packing

follower (key 10) nut clockwise.

Instruction Manual

D103363X012

26000 Valve

June 2017

20. Attach the actuator to the bonnet. Turn the actuator to thread the actuator stem onto the valve stem until the yoke

touches the shoulder of the bonnet.

21. Lock the drive nut (key 9), see figures 3, 2, and 4.

22. Apply 4 to 5 psi to the actuator for air-to-open or 13 to 14 psi for air-to-close.

23. With 50 psi air applied to port A, counter tighten the jam nuts (key 27) and slowly turn the valve plug and stem

assembly (key 4) clockwise to thread it into the actuator stem. Stop and lock the stem with the jam nut (key 27)

when port B shows some minimum flow.

24. Adjust the zero position of the travel indicator to the present position of the travel indicator disk (key 58).

25. Reduce air pressure to 3 psi for air-to-open or increase air pressure to 15 psi for air-to-close. For Cv < 1.0, there

should be no seat leakage (Class VI). For Cv > 1.0, the allowed leakage is Class IV. If leakage is noted, loosen the jam

nuts (key 27) and turn the plug and stem assembly (key 4) further into the valve bonnet (key 8).

26. At the lowest actuator travel position, the indicator disk (key 58) shall be at least 0.040 inches below the zero travel

position. If not, move the stem (key 4) further into the bonnet (key 8) and recalibrate the travel indicator.

27. Check the valve travel for a full 1/2 inch from the zero point on the indicator scale.

28. Check the dead band of the actuator. The difference between the signal to move the stem up and the signal to

move stem down shall not exceed 2 psi. If it does exceed 2 psi, the secondary packing (key 14) is too tight.

29. See appropriate actuator instructions to set the travel stops. (Refer to illustrations in the appropriate actuator

instruction manual to determine what type of stops are being used).

30. Attach and calibrate the positioner.

Note

Travel should commence from the zero travel indicator mark at 3.2 psi (4.3 mA) air-to-open or at 14.8 psi (19.7 mA) air-to-close.

The flow should enter only through the lower port A to help energize the V-ring packing set (key 17).

Instruction Manual

D103363X012

26000 Valve

June 2017

Parts Ordering

When corresponding with your Emerson sales office or Local Business Partner about this equipment, always mention

the valve serial number. When ordering replacement parts, also specify the key number, part name, and desired

material using the following parts tables.

WARNING

Use only genuine Fisher™replacement parts. Components that are not supplied by Emerson Automation Solutions should

not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the

performance of the valve, and could cause personal injury and property damage.

Parts List

Note

Contact your Emerson sales office or Local Business Partner for Part

Ordering information.

Table 1. Parts List

Key No. Description CL150 / PN 10, 16, & 25 CL300

Valve Body with PTFE Insert, Cv= 0.001 - 1.0 26514 26514-3

Valve Body with PTFE Insert, Cv= 2.5 26526 26526-3

Valve Body with PTFE Insert, Cv= 4.2 26532 26532-3

3* Spacer (Cv = .001 - 1.0 ONLY) 26507 26507

Plug & Stem Subassembly, Cv=0.001 26520-008-999(1)

Plug & Stem Subassembly, Cv=0.005 26520-007-999(1)

Plug & Stem Subassembly, Cv=0.01 26520-006-999(1)

Plug & Stem Subassembly, Cv=0.02 26520-005-999(1)

Plug & Stem Subassembly, Cv=0.05 26520-004-999(1)

Plug & Stem Subassembly, Cv=0.1 26520-003-999(1)

Plug & Stem Subassembly, Cv=0.2 26520-002-999(1)

Plug & Stem Subassembly, Cv=0.4 26520-001-999(1)

Plug & Stem Subassembly, Cv=0.8 26545-001-999(1)

Plug & Stem Subassembly, Cv=1.0 26545-000-999(1)

Plug & Stem Subassembly, Cv=2.5 26527-002-999(1)

Plug & Stem Subassembly, Cv=4.2 26535-002-999(1)

8Bonnet 26505

Bonnet, Extension 26528

9Drive Nut (Yoke) 011757-003-153

10 Packing Follower 24490-1

12 Hex Clamp Nut 26542

14* Secondary Packing Kit, V-Ring, standard 24494T001

17* Primary Packing, Cv < 1.0 (6 rings) 26516

Primary Packing, Cv = 2.5 (6 rings) 26523

Primary Packing, Cv = 4.2 (9 rings) 26536

21 Line Flange Adapter Gaskets, qty 2 86814

27 Jam Nut, qty 2 971514-002-250

50 Bonnet Seal 26539

58 Travel Indicator 24299

1. Add letter T or H to the end of the part number to indicate Tantalum or N10276 nickel alloy plug material.

*Recommended spare parts

Instruction Manual

D103363X012

26000 Valve

June 2017

Figure 2. Valve Body for Cv Rating of 2.5

(Class IV Seat Leakage)

E1289

Figure 3. Valve Body for Cv Ratings of 0.001 to 1.0

(Class VI Seat Leakage)

E1287

Figure 4. Valve Body for Cv Rating of 4.2

(Class IV Seat Leakage)

E1288

CAUTION

It is highly recommended that the included PTFE

encapsulated line flange adapter gaskets (key 21) be

utilized.

Figure 5. Baumann 26000 Valve Body Shown Upside

Down for Assembly Procedure

E1368

Instruction Manual

D103363X012

26000 Valve

June 2017

Figure 6. Secondary Packing: Spring-Loaded PTFE

V-Ring Packing Kit

E1240

Table 2. Secondary Packing Spring-Loaded PTFE

V-Ring Packing Kit, Part Number 24494T001

Key Number Description Material

6 Spring ASTM A313 S30200

14 Packing Set PTFE/carbon-filled PTFE

16 Washer ASTM A240 S31600

20 Spacer J-2000

(filled-Polytetrafluoroethylene)

Table 3. Baumann 26000 Valve and Actuator

Weights

VALVE WEIGHT ACTUATOR WEIGHT

kg lbs kg lbs

3.3 7.3 4.5 10

Figure 7. Dimensions NPS 1 26000 Valve with Baumann 32 Actuator and Dual Travel Stops

216

(48.5)

(2.25)

E1290

229

(9.0)

114

(44.5)

71 (2.8)

216

(48.5)

31 (1.24)

ADJUSTABLE OPEN-CLOSED

DUAL TRAVEL STOPS

PROVIDED AS STANDARD

(1.75) PTFE COVERED LINE-

FLANGE ADAPTOR GASKETS

PROVIDED WITH VALVE.

(6.35 mm, 0.25 INCH

THICK)

1/4 NPT

CL300

CL150

DN 25

PN 10, 16, 25

(inch)

40.625

4 HOLES ON

43.25 B.C.

40.75

4 HOLES ON

43.50 B.C.

Instruction Manual

D103363X012

26000 Valve

June 2017

CAUTION

The PTFE valve body insert protrudes slightly beyond both sides of the valve body (key 1). It is highly recommended that

the included PTFE encapsulated line flange adapter gaskets (key 21) be utilized.

Figure 8. Dimensions for Baumann 32 Actuator with Options

216

(48.5) 141

(5.5)

127 (5.0)

163

(6.4)

227

(8.96)

E1291

229

(9.0)

OPTIONAL FISHER 3660/3661

POSITIONER

TOP-MOUNTED

HANDWHEEL FOR AIR-

TO-CLOSE / FAIL OPEN

ACTUATION

OPTIONAL FIELDVUE DIGITAL

VALVE CONTROLLER

TOP-MOUNTED

HANDWHEEL FOR

AIR-TO-OPEN / FAIL

CLOSED ACTUATION

160 (46.3)

(3.7)

216

(48.5)

152 (46.0)

OPTIONAL FIELDVUE

DVC2000 DIGITAL VALVE

CONTROLLER

DUAL STOPS FOR AIR-

TO-CLOSE / FAIL OPEN

ACTUATION

USE HANDWHEEL AS

TRAVEL STOP

USE HANDWHEEL AS

TRAVEL STOP

(inch)

Tabla de contenidos

Otros manuales de Unidad de control de Emerson

Emerson

Emerson ALCO Thermo TX6 Manual de usuario

Emerson

Emerson Fisher ET Manual de usuario

Emerson

Emerson RAIMONDI Manual de usuario

Emerson

Emerson 8323G0 Series Instrucciones de instalación y funcionamiento

Emerson

Emerson Fisher OS2 Manual de usuario

Emerson

Emerson Fisher 92C Manual de usuario

Emerson

Emerson Fisher A11 Manual de usuario

Emerson

Emerson EX4 Manual de usuario

Emerson

Emerson RSTi-OM Manual de usuario

Emerson

Emerson Fisher POSI-SEAL A31A Manual de usuario

Emerson

Emerson Anderson Greenwood 400 Series Guía rápida

Emerson

Emerson Fisher Baumann 87000 Manual de usuario

Emerson

Emerson Fisher Large ED Manual de usuario

Emerson

Emerson Fisher 122A Series Manual de usuario

Emerson

Emerson QC54 FOUNDATION Manual de usuario

Emerson

Emerson BM6X Series Manual de usuario

Emerson

Emerson Fisher POSI-SEAL A81 Manual de usuario

Emerson

Emerson Keystone K-Lok 360 Series Instrucciones de funcionamiento

Emerson

Emerson Alco Controls CVE-014 Manual de usuario

Emerson

Emerson 63EG Manual de usuario

Emerson

Emerson Anderson Greenwood 93 Series Manual de usuario

Emerson

Emerson PACSystems VersaMax IC200BEM002 Manual de usuario

Emerson

Emerson fisher EDR Manual de usuario

Emerson

Emerson Fisher N201 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario