Elsner elektronik KNX RF-MSG-DST Guía

Installation and Adjustment

Item number 70712

KNX RF-MSG-DST

Rad io actuator

1 Contents

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Radio actuator KNX RF-MSG-DST • from software version 0.1.0 ETS programme version 1.0

Status: 27.06.2018 • Subject to technical changes. Errors excepted.

1. Description ........................................................................................... 3

1.0.1. Scope of delivery .......................................................................................... 3

1.1. Technical Data .......................................................................................................... 3

2. Installation and start-up ....................................................................... 4

2.1. Installation notes ...................................................................................................... 4

2.1.1. Safety advice ................................................................................................. 5

2.2. Notes on wireless equipment ................................................................................. 5

2.3. Connection ................................................................................................................ 5

2.3.1. Device Design ................................................................................................ 7

2.4. Establish radio connection ...................................................................................... 7

2.5. Activate retransmitter function ............................................................................... 8

2.6. Notes on mounting and commissioning ................................................................ 8

3. Transfer protocol ................................................................................. 9

3.1. List of all communication objects ........................................................................... 9

4. Parameter setting .............................................................................. 12

4.1. General settings ..................................................................................................... 12

4.2. Operating Mode ..................................................................................................... 12

4.2.1. Drive - Shutter, Blind, Awning, Window ................................................... 12

4.3. Control ..................................................................................................................... 15

4.3.1. Manual ......................................................................................................... 20

4.3.2. Automation – external ................................................................................ 21

4.3.3. Scenes ......................................................................................................... 21

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Installation, inspection, commissioning and troubleshooting of the device

must only be carried out by a competent electrician.

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

“Control unit”

The symbol is followed by a menu path. In this menu the settings

just described can be changed.

“Manual”

The symbol is followed by chapter information with a page num-

ber. In this chapter you will find additional information about the

setting just described.

3 Description

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

1. Description

The KNX RF-MSG-DST is a radio actuator for KNX radio (KNX RF). The actuator con-

trols one drive (blind, shutter, awning or window). Via an additional connector, another

motor control unit is supplied with power (loop-through function).

The KNX RF-MSG-DST uses the KNX RF S standard.

Functions:

• 1 connection for 230 V-drive (STAK3)

• 1 output 230 V AC (STAK3) for supply of further motor control units

• Reception of the control signal via radio KNX RF

•Retransmitter function (from version 1.1): Forwarding of all received KNX

RF telegrams. These can be received by KNX RF participants with the same

domain address. This allows the range of the KNX RF signal to be increased

•Automatic runtime measurement of the drives for positioning (incl. fault

reporting object)

•Position feedback (movement position, also slat position for shutters)

•Position storage (movement position) via 1-bit object (storage and call-up

e.g. via buttons)

•Scene control for movement position with 16 scenes per drive (also slat

position for shutters)

•Blocking objects and alarm reports have different priorities, so safety

functions always take precedence (e.g. wind block)

• Manual or automatic priority setting via time or communication object

•Brief time limit (movement command blocked) and 2 movement limits

Configuration is made using the KNX software ETS 5. The product file can be down-

loaded from the ETS online catalogue and the Elsner Elektronik website on www.els-

ner-elektronik.de in the “Service” menu.

1.0.1. Scope of delivery

•Actuator

• Magnet for teaching procedure (telescopic rod)

• Rubber seal

Available accessories:

• Mains connection wire (5 m)

• Connection wire (available in 1 m; 2,5 m; 5 m)

1.1. Technical Data

Housing Plastic

Protection category IP 54*

Dimensions approx. 149 x 72 x 29 (W x H x D, mm)

Weight approx. 168 g

Ambient temperature Operation -25…+70 °C, storage -30…+85°C

4 Installation and start-up

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

*The Radio actuator KNX RF-MSG-DST should be installed in a protected area

despite a high protection category because water can enter in via the connectors.

Please observe the instructions in Chapter Connection.

The product conforms with the provisions of EU directives.

2. Installation and start-up

2.1. Installation notes

Installation, testing, operational start-up and troubleshooting should

only be performed by an electrician.

DANGER!

Risk to life from live voltage (mains voltage)!

There are unprotected live components within the device.

• VDE regulations and national regulations are to be followed.

• Ensure that all lines to be assembled are free of voltage and take

precautions against accidental switching on.

• Do not use the device if it is damaged.

• Take the device or system out of service and secure it against

unintentional use, if it can be assumed, that risk-free operation is no

longer guaranteed.

The device is only to be used for its intended purpose. Any improper modification or

failure to follow the operating instructions voids any and all warranty and guarantee

claims.

After unpacking the device, check it immediately for possible mechanical damage. If it

has been damaged in transport, inform the supplier immediately.

The device may only be used as a fixed-site installation; that means only when assem-

bled and after conclusion of all installation and operational start-up tasks and only in

the surroundings designated for it.

Ambient humidity max. 95% RH, avoid condensation

Operating voltage 230 V AC

Input STAS3 plug (230 V)

Output 1 x 230 V AC (loop-through), STAK3 coupling, max. 1.5

kW switch-on load per mains connection

1 × drive, STAK3 coupling, 230 V AC (up/down/N/PE),

loadable to max. 4 A / 230 V AC

Communication objects 52

Assignments max. 1024

Radio frequency 868,3 MHz

5 Installation and start-up

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

2.1.1. Safety advice

WARNING!

Risk of injury caused by components moved automatically!

If the wireless connection between the control unit and the wireless

actuator is interrupted, connected devices can no longer be operated.

• For that reason do not connect drives to the wireless actuator which

could be hazardous to human life!

2.2. Notes on wireless equipment

When planning facilities with devices that communicate via radio, adequate radio re-

ception must be guaranteed. The range will be limited by legal regulation and struc-

tural circumstances. Avoid sources of interference and obstacles between receiver and

transmitter, that could disturb the wireless communication. Those would be for exam-

ple:

• Walls and ceilings (especially concrete and solar protection glazing).

• Metal surfaces next to the wireless participants (e. g. aluminium construction

of a conservatory).

• Other wireless devices and powerful local transmitters (e.g. wireless

headphones), which transmit on the same frequency. Please maintain a

minimum distance of 30 cm between wireless transmitters for that reason.

2.3. Connection

The radio module is connected between the appliance and the power supply. It may

only be connected to flexible lines using STAK/STAS connectors. The connectors must

be locked using the locking bow.

Do not expose to continuous sun radiation to avoid overheating.

The housing is not UV-resistant.

• Assembly the device in a protected area (e. g. in

the box for the blinds/marquee/shutters in a construction

profile beneath the roof tiles or in a housing).

The antenna symbol on the housing shows the

position of the antenna in KNX RF-MSG-DST. This

side must not be positioned directly on metal

surfaces or objects. Otherwise, the radio signal might

disturbed.

Metal

profile

KNX RF-MSG-DST

6 Installation and start-up

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

No water may run along the supply line and device because water

can enter in via the connectors.

• Assembly the device in a protected area (e. g. in

the box for the blinds/marquee/shutters in a construction

profile beneath the roof tiles or in a housing).

• Lay the supply lines out and down from the device.

No vibrations!

• Assemble the device in a place that is free of vibrations.

7 Installation and start-up

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

2.3.1. Device Design

2.4. Establish radio connection

The device is integrated into the KNX system with a media coupler or a KNX RF USB

stick. (For further information see the corresponding manual/data sheet.)

1. Start the programming mode of the KNX RF-MSG with the enclosed magnet (teles-

copic rod). The programming LED lights up.

1 Neutral conductor

3 nc (not connected)

Motor output

STAK3 coupling

for STAK3 plug

Input mains voltage

STAS3 plug for

STAK3 coupling

1Neutralcond.

2Up

3Down

Output

mains voltage

STAK 3 coupling

for STAK3 plug

1 Neutral cond.

3nc(

PRG

Magnet

(side)

and LED

8 Installation and start-up

Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.

2.5. Activate retransmitter function

2.6. Notes on mounting and commissioning

Device must not be exposed to water (rain). This could result in the electronic being

damaged. A relative air humidity of 95% must not be exceeded. Avoid bedewing.

If the device is set up as a retransmitter, it transmits

all received KNX RF telegrams. These can be recei-

ved by KNX RF participants with the same domain

address. As a result, the radio range of a KNX RF

system can be increased.

The function must be activated in the ETS in the pro-

perty window of the device by ticking the box "Re-

transmitter".

Tabla de contenidos

Otros manuales de Controladores de elsner elektronik

elsner elektronik

elsner elektronik Cala Touch KNX Manual de usuario

elsner elektronik

elsner elektronik KNX S-B2-UP 230 V Manual de instrucciones

elsner elektronik

elsner elektronik KNX Touch One Style Manual de usuario

elsner elektronik

elsner elektronik KNX K8 Guía

elsner elektronik

elsner elektronik KNX RF-MSG2-DST Manual de usuario

elsner elektronik

elsner elektronik KNX S1R-B4-UP DES Guía

elsner elektronik

elsner elektronik 70711 Manual de usuario

elsner elektronik

elsner elektronik KNX S4-B10 230 V Manual de usuario

elsner elektronik

elsner elektronik KNX S1R-B4-UP DES Manual de usuario

elsner elektronik

elsner elektronik KNX RF-MSG-ST Manual de usuario

elsner elektronik

elsner elektronik KNX DALI L4 bc 16 A Guía

elsner elektronik

elsner elektronik KNX S1R-BA4-UP Guía

elsner elektronik

elsner elektronik KNX S2 Manual de usuario

elsner elektronik

elsner elektronik KNX R1-B4 compact 16 A Guía

elsner elektronik

elsner elektronik RF-MSG2-DST Manual de usuario

elsner elektronik

elsner elektronik KNX K4 Manual de usuario

elsner elektronik

elsner elektronik KNX S-B4T-UP 230 V Manual de instrucciones

elsner elektronik

elsner elektronik Nunio KNX M-T Guía

elsner elektronik

elsner elektronik KNX eTR 205 Light Guía

elsner elektronik

elsner elektronik KNX eTR MultiTouch Manual de usuario

elsner elektronik

elsner elektronik KNX RF S1R-B2 compact Guía

elsner elektronik

elsner elektronik KNX S4-B12 DES Manual de usuario

elsner elektronik

elsner elektronik KNX R4 16 A Guía

elsner elektronik

elsner elektronik KNX S1R-B4 compact Guía

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

elsner elektronik KNX RF-MSG-DST Guía

Manuales populares de Controladores de otras marcas