Elmo HC7501 Manual de usuario
HC7501
INSTRUCTION MANUAL
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
· Do not use any power supply other than
specified.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
* The CAUTION label is attached on the
bottom of camera.
INFORMATION
This equipment has been tested and found
to comply with the limits for Class A digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection against
harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, use, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a
residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his
own expense.
USER-INSTALLER CAUTION: Your
authority to operate this FCC verified
equipment could be voided if you make
changes or modifications not expressly
approved by the party responsible for
compliance to Part of the FCC Rules.
- 1 -
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, install in accordance with the
manufacturer's instructions.
8. Do not install near heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Only use attachment/accessories specified by the manufacturer.
10. Unplug this apparatus during lighting storms or when unused for long periods of
time.
11. Refer all servicing to qualified personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have been fallen onto the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
- 2 -
PART NAMES AND FUNCTIONS
4
60 (2.4)
3
1
2
2
6
7
9
10
5
8
33 (1.3)
140 (5.5)
33 (1.3)
60 (2.4)
Lens mount
Mount a CS-mount lens. For C-mount lens or C-mount coupler, use supplied C-mount ring.
Camera mount
For mounting a camera on bracket, tripod, etc. (1/4"-20UNC thread)
Back focus dial
Refer to "HOW TO USE" on page 4 for details.
IRIS terminal
Connect when an automatic iris lens is used.
VIDEO OUT terminal
Connect to a monitor TV, etc. (BNC connector)
S-VIDEO OUT terminal
Connect to a VCR with S-video terminal. (MiniDIN4Pjack)
SC-phase adjustment
Adjustment the SC phase of external synchronous control.
Camera control switches
[Display button, Shift button, Select button, Data button (up, down)]
Refer to "CAMERA CONTROLS (OSD)' on page 6.
8
7
6
5
4
3
2
1
All dimensions in mm (inch)
- 3 -
HOW TO CONNECT
Before connection, make sure that power of all units to be connected are OFF and cords are unplugged.
1. Mount a lens onto the camera. Refer to "HOW TO USE" on page 4 for usable lens.
2. Connect video terminal of the camera and the video input terminal of a monitor TV, etc. with a
75Ωcoaxial cable.
3. Connect the 4P-connector cable for 12VDC power and the 12P-connector, which
accommodates 12VDC input, external sync input and Y/C output. (You may procure separately
the cable assemblies by using supplied connectors or purchase them from ELMO as an option)
Caution: Installation should be made by a qualified service personnel and should conform to
all local codes.
Lens, coaxial cable for video signal and power supply are not supplied with a
camera.
Don't connect the S-VIDEO terminal and "Y/C OUT" of 12P terminal at the same
time.
Do not supply 12VDC from 4P-connector and 12P-connector simultaneously.
4P terminal
Connect this to the DC 12V power supply.
(Refer to Fig.1)
12P terminal
This 12-pin connector has following inputs
and an output.
· DC 12V input (Do not use DC 12V from
4P terminal simultaneously.)
· External sync. input.
· S-VIDEO (Y/C) output. (Refer to Fig.2)
10
9
1
23
41
2
3
4
Name
12V
12V
GND
GND
Role of Signal
DC IN 12V
DC IN 12V
GND
GND
Soldering side
Connector Pin Assignments
1
2
3
456
7
8
9
10
11 12
1
2
3
4
5
6
Name
GND
12V
GND
Y
NC
NC
Role of Signal
GND
DC IN 12V
GND
Y OUT
No connection
No connection
7
8
9
10
11
12
Name
EXT. SYNC
GND
C
GND
12V
GND
Role of Signal
EXT. SYNC IN
GND
C OUT
GND
DC IN 12V
GND
Soldering side
Connector Pin Assignments
(Fig. 2)
Supplied plug
(HIROSE HR10A-7P-4S)
Supplied plug
(HIROSE HR10A-10P-12S)
(Fig. 1)
- 4 -
HOW TO USE
1. Adjust the iris and focus of the lens so that optimum image
may be obtained.
* Usable lenses
CS-mount lenses, whose length "L" (in the illustration)
from the bearing surface of the mount is 5mm or less if
protruded, should be used.
*For C-mount lenses or C-mount coupler, use a supplied
5mm ring between the lens and camera.
Adjust the back-focus only when necessary.
Note: Adjustment of the lens back-focus.
The camera is set at the factory for standard back focus position. Some zoom lenses may
require slight adjustment to the back focus. In those cases, follow these instructions.
Adjust the lens back-focus by turning the back focus dial in either direction as per the
illustration, referring to the following instructions.
Place an object at any fixed distance and set the focus ring of the zoom lens accordingly.
Set the zoom lens to full TELE position and obtain the best focus position by turning the
focus ring on the zoom lens.
Set the zoom lens to full WIDE position and obtain the best focus position by turning the
back focus dial located on the side of the camera.
3
2
1
Lens
CS-mount
5mm or less
L
Camera Lens
Back focus dia
l
Repeat procedures and until focus remains constant throughout the zooming range.
Note: When the weight of the lens is more than 1kg (2.2lbs), the camera should be supported by
the lens rather than relying on camera mounting screw.
* Using an auto iris lens
When a DC driven type auto iris lens is used, set the IRIS address (OSD) at DC and connect the
plug of the lens to the IRIS terminal at the side of the camera.
When a video feedback type auto iris lens is used, set the IRIS address (OSD) at VIDEO and
connect the plug from the lens to the IRIS terminal at the side of the camera. (Refer to the lens
manual for the level adjustment.)
* When a video feedback type auto iris lens (peak/average selectable type) is used at peak mode,
the BLC feature of the camera may not function correctly. In such a case, change the mode to
average.
* When using at auto iris lens, set the shutter mode at OFF (OSD).
* The shutter mode at AUTO (OSD) may increase smears on monitors, which is caused by
characteristics of CCD and that is not fault of the camera.
324
VIDEO setting (OSD)
+9V iris power (50mA Max.)
GND
0.7Vp-p auto iris video signal
GND
DC setting (OSD)
Control -
Control +
Drive +
Drive - (GND)
1
2
3
4
IRIS terminal Pin Assignments
Plug for IRIS terminal
(CHUOMUSEN E4-191J-150) Soldering side
- 5 -
(a) Internal Synchronous Control
(b) External Synchronous Control by VBS
The internal sync. mode automatically changes to the external sync. mode when the VBS signal
from an external control unit is supplied to 'EXT. SYNC' of 12P terminal on the back of the
camera.
*Required signal for the external synchronization
VBS (75Ωunbalanced) SYNC 0.3Vp-p ± 0.1Vp-p
BURST 0.3Vp-p ± 0.1Vp-p
Limits of frequency deviation within ± 50ppm against the NTSC standard system.
(Horizontal frequency approx. 15.7335kHz ~ 15.7350kHz)
In case of synchronous use of more than two cameras. Horizontal phase and Sub-carrier (SC)
phase can be adjusted to match the images from respective cameras, if necessary.
CAMERA
To DC 12V power supply
Monitor TV
CAMERA
To DC 12V power supply
PG/CAMERA
C-SYNC./C-VIDEO
Monitor TV
INT./EXT. SYNCHRONOUS CONTROL
- 6 -
CAMERA CONTROLS (OSD)
To set up the camera, use the SETUP screen displayed on your monitor TV.
1. SETUP OF EACH FUNCTION
DISPLAY SHIFT
SELECT
UP
DATA
DOWN
(Back side of the camera)
1. Press the DISPLAY button on the back side of the camera to display the SETUP screen on
your monitor TV.
2. Use the SHIFT button to choose the mode.
3. Use the SELECT button to choose the address.
4. Use the DATA (UP and DOWN) buttons to choose the data.
5. When the setup is completed, move the cursor to END by pressing the SHIFT button.
Choosing MEMORY and pressing DISPLAY button stores the latest settings to the
memory. Choosing CLEAR and pressing DISPLAY button clears the settings and the
camera returns to the factory settings.
6. When you have made changes to the setting, make sure to move the cursor to END and
press the DISPLAY button to clear the setup screen. At that point, the settings are stored to
the camera. Remember that turning off the unit while the setup screen is displayed will not
store the settings and it returns to the previously-stored settings.
- 7 -
2. CAMERA CHARACTER (CHR)
(Factory setting is OFF.)
(1) ON:
You can display up to 7 characters.
The blinking character is the one currently
selected. Each time you press the DATA
button, the character changes in the order listed
in the following table.
Press the DISPLAY button to move the
blinking mode to the next character, and you
can select it by pressing the DATA buttons.
When the OSD display disappears, characters
are displayed in white at the bottom of the
screen.
(2) OFF:
Characters do not appear.
Characters that can be used
- 8 -
3. WHITE BALANCE (WB)
Allows you to make the white balance adjustment automatically or manually, for a color
temperature range 2900K - 8000K. (Factory setting is AUTO.)
(1) AUTO:
Sets the automatic color temperature tracking mode. White balance may not be adjusted if
the lighting conditions are bad.
(2) MANU:
Sets the manual adjustment mode. This mode is effective for imaging with low variations
in color temperature.
(3) PUSH:
Use when you want to adjust the white balance with one-push operation. This allows you
to make more accurate adjustment than the AUTO mode. This mode is effective for
imaging with low variations in color temperature. Pressing the UP button after selecting
PUSH sets the data.
4. AGC (AGC)
When the sensitivity selection switch at the left side of the camera is ON, the following
adjustments are enabled: (Factory setting is ON.)
(1) ON:
Allows you to specify the maximum gain for
AGC.
Choices include 6dB, 12dB, and 18dB.
(Factory setting is 12dB.)
(2) OFF:
Allows you to adjust the camera gain manually.
5. SHUTTER (SHUT)
Select either manual or automatic selection of the electronic shutter. (Factory setting is OFF.)
(1) OFF:
Factory setting (1/60 sec)
(2) AUTO:
Automatically selects the electronic shutter.
(3) HS1:
You can select among the 8 shutter speeds.
Choose one from:
1/100 1/125 1/250 1/500 1/1,000 1/2,000
1/4,000 and 1/10,000 sec.
(4) HS2:
You can specify the shutter speed from 1H to
262H in 1H increments.
(approx. 1/10,000 sec - 1/60 sec)
Choosing the AUTO mode or the high speed shutter
mode under the illumination of a flurescent light
may cause flicker or change in the white balance.
In this case, set SHUT to the OFF mode and use
the auto iris lens.
(5) LS1:
In the slower-side shutter, you can specify the
speed from 2F (field) - 510F (field) in 2F
increments.
NTSC: (2/60 sec - 510/60 sec)
(6) AUTO2:
Automatically changes the slower-side shutter
depending on the quantity of light. You can
also choose the upper-limit speed from 2F, 4F,
8F, 16F, 32F and 64F.
* If you choose 1/100, there will be no flicker
even when the object becomes brighter.
* In case the accumulated time becomes long
in the slower-side shutter mode while
shooting a fast-moving object, the picture
may viewed with after-image.
FREEZE PICTURE MODE
You can enter the freeze picture (field) mode by pressing the DOWN button of the data
button while the SHUTTER mode is OFF.
To return to the original live picture, press the DOWN button again.
- 9 -
Otros manuales para HC7501
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Elmo
Elmo
Elmo X Line TND4003X Manual de usuario
Elmo
Elmo PTC-201CIP Manual de usuario
Elmo
Elmo PTC-200C Manual de usuario
Elmo
Elmo ESD-370 Manual de usuario
Elmo
Elmo PTC-400C Manual de usuario
Elmo
Elmo TSN420D Manual de usuario
Elmo
Elmo PTC-100S Manual de usuario
Elmo
Elmo QSN301D Manual de usuario
Elmo
Elmo TNC4604 Manual de usuario
Elmo
Elmo Dome Camera TND4104X Manual de usuario
Elmo
Elmo One-Piece Color Video Micro Camera MN30 Manual de usuario
Elmo
Elmo UN411E Manual de usuario
Elmo
Elmo CCD Color Dome Camera TSN400A Manual de usuario
Elmo
Elmo GIR-S7322WS Manual de usuario
Elmo
Elmo HC7001 Manual de usuario
Elmo
Elmo ESD-300DR Manual de usuario
Elmo
Elmo BUTP200 Manual de usuario
Elmo
Elmo Dome Camera TND4004 Manual de usuario
Elmo
Elmo PTC-200C Manual de usuario
Elmo
Elmo HC7501 Manual de usuario
