Elmo Vandal Resistant Dome Camera TND4204VX Manual de usuario

VANDAL RESISTANT DOME CAMERA

INSTRUCTION MANUAL

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated "dangerous

voltage" within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

TND4204VX

INFORMATION

This equipment has been tested and found

to comply with the limits for Class A digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference when the equipment

is operated in a commercial environment.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a

residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his

own expense.

USER-INSTALLER CAUTION: Your

authority to operate this FCC verified

equipment could be voided if you make

changes or modifications not expressly

approved by the party responsible for

compliance to Part of the FCC Rules.

CAUTION

•Do not use any power supply other than

specified.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK.

* The CAUTION label is attached on the

bottom of camera.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with dry cloth.

6. Do not block any ventilation openings, install in accordance with the manufacturer's

instructions.

7. Do not install near heat sources such as radiators, heat registers, stoves or other apparatus

(including amplifiers) that produce heat.

8. Only use attachment/accessories specified by the manufacturer.

9. Unplug this apparatus during lighting storms or when unused for long periods of time.

10. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, objects have been fallen

onto the apparatus, does not operate normally, or has been dropped.

Name and Function of Each part

No. Name Function

The mounting bracket for ceiling installation.

The main body of the camera section.

For adjusting the image size.

For adjusting the focus.

Protective cover for the lens.

Protective cover for the main body.

Camera mounting bracket

Main body

Zoom ring

Focus ring

Cover lens

Dome cover main body

Used when the white balance is in the PUSH mode.

For setting the vertical sync. phase.

For adjusting the brightness of the image.

For locking the tilt after adjusting the image up/down

direction.

Connect this to output images. When adjusting the image

shooting direction, field angle or focus (in wiring work, for

example), connect a monitor TV, etc.

Image output terminal to be connected to the image input

terminal such as monitor TV.

Connect this to the AC24V 60Hz or DC12V power supply.

Refer to P4.[Selector Switch (Details)]

For fixing the camera mounting bracket with

screws.(Gang box)

Used when the wiring duct is connected.

No. Name Function

AW PUSH

DOWN/UP

ALC adjustment volume

Tilt lock screw

Monitor terminal

BNC cable

AC/DC power cord

Selector switch

Screw hole for

mounting bracket

Parallel pipe threads(G1/2)

Parallel pipe threads(G3/4)

Selector switch (Details)

1.SENS UP switch

To set the max. value (upper limit value) of the

operating gain in the auto gain control circuit, set this

switch to ON position. In case the back lighting is too

dark and the camera sensitivity is insufficient, set this

switch to ON position.

2. BLC (Back Light Control) switch

In case the back lighting is too bright to view the

main object clearly, set this switch to ON position.

3. INT/LL switch(Set at LL position from the factory)

a. INT. (internal) control switch

When the internal synchronization is used, set the switch to the INT side.

b. L.L. (Line-lock) control switch

Matching the vertical synchronization with the power frequency is called the

line-lock.

When two or more cameras are connected to a monitor TV through a video

switcher, the vertical sync. phase can be locked with the power frequency, and

a stable vertical sync. is obtained without being disturbed at the time of

switching. Line-Lock is operative only when the AC24V 60Hz power supply is

connected.

Use Down/up Buttons to adjust the vertical sync. phase.

4. PUSH/ATW switch

This is the switch to select the white balance PUSH/ATW.

PUSH: When the lighting from the source is constant, it is possible to fix the AW

setting.

Place something white (paper, etc.) in front of the lens in a way that the

whole screen may be covered, then push the AW PUSH switch. At this

moment the setting is saved and retained even after the power is turned

OFF.

ATW: The camera automatically adjusts the white balance as it continuously

measures the color temperature of the lighting source.

5. 1/100s

When this switch is turned ON, the shutter speed is set to 1/100 second. It is

effective in reducing the light intensity.

Caution:

When this switch is turned ON, AES does not operate.

1/100S

PUSH/ATW

INT/LL

BLC

SENS UP

ON OFF

(This figure shows the setting

before shipment from our factory.)

How to Install

1. Make holes in the mounting surface.

(Fig. 1)

The paper pattern for installation is

included.

2. Remove the dome cover main body

fixing screws from the camera body.

(Fig. 2).

Use the dedicated wrench (Attached).

Be careful not to drop the cover

dome.

Camera

mounting

bracket

Cover dome

screw

Dedicated wrench

(Attached)

Dome cover

main body

(Fig.2)

(Fig. 1)

Front of camera

Camera mounting

bracket mount

screw

(not attached)

Front of

camera

Camera

mounting

bracket

3. Remove the main body fixing screws,

and remove the main body from the

camera mounting bracket. (Fig. 3).

Remove the screws identified by the

mark(Figs. 4).

4. Fix the camera body to ceiling, wall or

box with the camera body fixing screws.

(Fig.5)

Make sure that it is fixed firmly.

Make sure of the position of the front

of the camera.

Camera

mounting

bracket

Main

body

Main body

mount screw

(Fig.3)

(Fig.4)

(Fig.5)

Base pan

Lens

(Fig.7)

Camera mounting bracket

BNC

cable

Power cord

Main body

5. Connect the power cord and the BNC

cable, and then mount the main body on

the camera body. (Fig. 6).

· When you connect the Power cord and

the BNC cable, roll the waterproof tape

to prevent water damage as the figures

below indicate.

6. While watching the monitor, adjust the

image direction.

· Right/left direction (Fig.7)

Rotate the base pan to right or left, and

adjust the right/left direction.

· Up/down direction (Fig.8)

Loosen the tilt lock screw, and adjust

up/down direction.

After setting the up/down direction,

fasten the tilt lock screw.

(Fig.6)

Warning

Weight of the camera mounting

bracket and mounting metal

piece is 1600g(3.52lbs).

Make sure that the ceiling or wall

is strong enough to support the

weight of the camera mounting

bracket and mounting metal

piece altogether.If not strong

enough, the device may drop

and injure the personnel around.

Caution

Please do not hold a part of the

lens, when adjusting the image

direction. It may cause a

breakdown of the lens.

Power cord

BNC cable

Be careful not to drop the tilt lock

screw.

Manually fasten the tilt lock screw.

If fastened with pliers or the like, the

tilt lock screw may be broken.

7. Correct the image tilt. (Fig.9)

Be sure to hold the cover motor.

8. Mount the cover lens, and mount the

dome cover with the dome cover fixing

screws. (Fig.10)

Camera mounting bracket

Lens

Tilt lock screw

(Fig.8)

Lens

Cover motor

(Fig.9)

Main body

Cover

lens

Dome

cover

(Fig.10)

166

(

6.54

)

101.6

(

4.00

)

Appearance

All dimensions in mm(inch)

When any failure is suspected

Symptoms

Image is not displayed.

Color is not correct.

Image is disarrayed.

Check here.

Are cables connected correctly?

Are the power plugs of peripheral units inserted correctly

into the receptacles?

Is the video monitor adjusted correctly?

Is any connector of this machine or video monitor loose or

contacted poorly?

Otros manuales para Vandal Resistant Dome Camera TND4204VX

Tabla de contenidos

Otros manuales de Cámara de seguridad de Elmo

Elmo

Elmo Dome Camera TND4004 Manual de usuario

Elmo

Elmo PTC-200C Manual de usuario

Elmo

Elmo TSN410D Manual de usuario

Elmo

Elmo ESD-300DR Manual de usuario

Elmo

Elmo PTC-200C Manual de usuario

Elmo

Elmo PTC-401CIP Manual de usuario

Elmo

Elmo TD4114IP II Manual de usuario

Elmo

Elmo Dome Camera TND4104X Manual de usuario

Elmo

Elmo TSE270X Manual de usuario

Elmo

Elmo TNC4604 Manual de usuario

Elmo

Elmo PTC-400C Manual de usuario

Elmo

Elmo CCD Color Video Camera TNC4604 Manual de usuario

Elmo

Elmo PTC-201CIP Manual de usuario

Elmo

Elmo Dome Camera TND4004 Manual de usuario

Elmo

Elmo SN2230IP II Manual de usuario

Elmo

Elmo QNW4000 Manual de usuario

Elmo

Elmo HC7501 Manual de usuario

Elmo

Elmo ESD-370 Manual de usuario

Elmo

Elmo BUTP200 Manual de usuario

Elmo

Elmo PTC-100S Manual de usuario

Elmo

Elmo QP49H Manual de usuario

Elmo

Elmo TNC4614X Manual de usuario

Elmo

Elmo HC7001 Manual de usuario

Elmo

Elmo MN400 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario