Elite Screens Tab-Tension 3 Series Manual de usuario

Rev. V07112023DT (DS0344) www.elitescreens.com 1

Kestrel Tab-Tension 3 Series

Floor Rising Tab-Tensioned Motorized Screen

User’s Guide – E/H Type (RC1)

V1.0

Visit www.elitescreens.com for latest updated version.

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third

party, then these instructions must be included.

Caution:

The screen’s Black Bottom Drop is already set to its maximum drop distance. There is

NO extra Black Bottom Drop in the roller. Please be aware of this as it will void your

warranty with Elite Screens®. Unapproved changes or modifications (except for cutting

the power cord for hardwire installations) to this unit are prohibited and will void your

warranty.

•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by

the manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

•The power outlet supplying power to the unit should be close to the unit and easily accessible.

•Do not install the unit on uneven or inclined surfaces.

•Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

•Never overload the power cord to prevent an electric shock or fire due to a loose contact or a

short circuit.

•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by

yourself. No one except authorized technicians can open and make repairs to this unit.

•Make sure the power source this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, make sure the cord has an equal rating as the

appliance to avoid overheat.

•Do not handle the power plug when your hands are wet, or your feet are in contact with water.

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 2

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind, thunder, or lightning.

•Avoid direct Sunshine, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from overheating.

•Cut off the power supply first before transportation or maintenance.

•Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

•Keep hands clear from the closing panels.

•Keep away from children when screen is in operation.

WARNING

Individual modifications to this product are prohibited and will void the manufacturer’s warranty. Please

contact the Elite Screens® Customer Service Team with any questions.

SCREEN MAINTAINANCE

Dust, dirt, and scratches on the projection screen surface will affect the quality and performance of the

projection image. For optimal results we advise to pay attention to the following instructions.

1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular

motion.

Wipe very gently when needed from left to right only.

2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or

cloth may damage the screen’s surface).

3) Gently wipe the screen with a lightly moistened microfiber cloth with mild soap diluted in water.

Notes：

The following precautions should be followed at all times to avoid damaging the

material, which is not covered under warranty.

▪Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the

material.

▪Don’t scratch the material, as it will leave permanent markings on the screen’s surface.

▪Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to

the material.

▪Don’t use acetone, benzene, alcohol, and any other organic solvents to clean the screen

material. Using such chemicals will permanently damage the screen.

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 3

FCC Regulatory Compliance

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 4

PARTS IDENTIFICATION

Note: Please always store the screen flat horizontally. Never store the screen in a vertical

position as it will permanently damage the screen’s structure, shift the material, and

cause wrinkles/folds which will void the warranty.

Screen material

Bottom black masking

border

Power terminal /

Power switch

Tab/Strings

Cross-rising spring

scissor mechanism

Case/Housing

Closing Panel/Lid

Feet

Front of screen

Back of screen

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 5

Kestrel Tab-Tension 3 | Controls and Accessories

A. IR (InfraRed)

Remote Control

ZRC1-IR

B. RF (Radio

Frequency) Remote

control ZRC1-RF

C. Wall box

controller

ZRC1-WB

D. RJ50 Cable

ZRC1-RJ50

E. AAA batteries

* Pre-installed

inside housing

SCREEN OPERATION

Electric Current: Depending on your region, the screen will operate in either 110v or 220v voltage.

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power

outlet.

2. Once the screen has power, you’ll be able to control it using any of the 5 methods described below.

5 ways to control your Kestrel Tab-Tension 3 Screen

1. IR Remote Control (Item A, Fig.1): The Infrared functions by direct line of sight contact using an

effective beam range of 25 feet within a 30-degree angle. Aim the IR remote directly at either the IR

receiver on the Wall Box Controller or on the screen to operate the screen.

Note: Assure there is no obstruction between the IR remote and IR receiver.

2. RF Remote Control (Item B, Fig.1): The radio waves eliminate the need for a direct line of sight

and has a longer distance control range.

The RF remote is already pre-synced/paired and ready to use. If synchronization/ pairing is

needed, please follow the steps below.

IR Lens

(IR remote only)

LED light

STOP

DOWN

IR/RF remote

Fig.1

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 6

How to synchronize/pair a new RF remote:

•Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-

box LED flashes). Reference the wall box controller section for programming key location.

•Then press the “Up Key” on the RF remote.

The Wall box LED will flash 5 times, to indicate the RF remote has been properly

synchronized/paired.

How to change the RF code (For use when multiple screens/RF remotes are owned, Fig.2)

Changing the RF code avoids controlling multiple screens at the same time and prevents electrical

interference leading to accidental control of the screen.

1. Remove the batteries

2. Change the RF code switch

3. Insert the batteries

4. Synchronize it with the wall box controller

3. Wall box controller (Item C, Fig.3): The wall box controller switch is a wall mounted control box

with an up/stop/down button. It plugs directly into the screen’s RJ50 port by RJ50 cable (Item D).

Battery

compartment

Default

“000”

RF Remote

BACK VIEW

Slide Switches

for RF Code

change

RJ50 cable

Wall box controller

SIDE VIEW

RJ50 PORT:

Connects to the

Screen RJ50

PORT (RJ50

CABLE ONLY)

3.5mm mono

Projector Trigger Port

(if Projector equipped)

Programming

Key

Wall box

controller

Wall box controller

BACK VIEW

Fig.2

Fig.3

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 7

4. Wired 5-12 volt trigger (Fig.4): Requires a 3.5mm to 3.5mm mono cable (Not included)

Step 1: Connect one end the RJ50 cable to the screen and the

other end to the Wall box controller.

Step 2: Then connect one end the 3.5mm mono cable to the wall

box controller and the other to the projector.

Once the two cables have been connected, the wired trigger

feature is ready to synchronize the screen’s up/down operation

with the projector’s power cycle.

•Projector on, screen drops

•Projector off, screen raises

5. Wireless 5-12 volt trigger (Fig.5): Requires a 3.5mm to 3.5mm mono cable (Not included).

The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld

remote control, or as a Wireless 5-12 volt trigger. The radio frequency technology sends a wireless

signal that synchronizes the screen’s drop & rise with the projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigger

The 5-12V wireless trigger should already be synced and ready to work.

Step1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm mono end of the cable to your projector

Step 3: Turn on the projector and the screen should automatically deploy.

Step 4: Turn off your projector and the screen should automatically retract.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-

30 seconds for full off and on cycle each time)

Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box

controller per the instructions in the Radio Frequency remote section.

Mono 3.5mm

Projector Trigger

Port

Fig 5

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

STOP

DOWN

Projector

RF remote control

SIDE VIEW

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

Wall box

controller

Fig. 4

Projector

RJ50 cable

User’s Guide Kestrel Tab-Tension 3 Series

Rev. V04122023AY (DS0344) www.elitescreens.com 8

ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)

Wall box controller must be connected to the screen.

1. Preset the Screen’s Drop Position:

Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it at.

Press & hold the “Programming Key”, then press the “Down key” on the Wall Box Controller. The LED will

flash 5 times to confirm new programmed drop position.

2. Clear/Reset the Screen’s Drop Position to factory default:

Press & hold the “Programming Key + “Stop key” on the wall box controller.

For more information, technical support or your local Elite Screens®contact,

please visit http://www.elitescreens.com/

PROGAMMING NOTE:

The programmed vertical position relies on a time-count which adjusts itself according to the

programmed timed difference. Multiple up/down programming will result in the vertical position

being off a few inches. It is recommended that programming is done the first-time the desired

vertical position is determined or RESET it to factory default and programming the desired vertical

position afterwards.

ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the projection

surface on tab-tension screens. The full drop is recommended to allow the screen to rely on the tab-

tension system to maintain the projection surface flat and taut on all sides.

The same applies on non-tensioned screens, although some level of waves may be present due to the

nature of the screen not being tensioned. If wrinkles/waves develop after making the adjustment to

the desired drop position, reset it to the factory’s default position per the instructions below.

FLATNESS AFFECTED BY NEW PROGRAMMED VERTICAL POSITION IS NOT COVERED UNDER A

REPLACEMENT WARRANTY.

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens Manual Series Manual de usuario

Elite Screens

Elite Screens OMS103HR Manual de usuario

Elite Screens

Elite Screens 100 series Manual de usuario

Elite Screens

Elite Screens VMAX113XWS Manual

Elite Screens

Elite Screens AR100H Manual de usuario

Elite Screens

Elite Screens QuickStand Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual

Elite Screens

Elite Screens Evanesce Tension Series Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens F100XWH1 Manual de usuario

Elite Screens

Elite Screens Elite Home 2 Series Manual de usuario

Elite Screens

Elite Screens EDGE FREE Aeon Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens Manual Series Manual de usuario

Elite Screens

Elite Screens SILVERMAX106H2 Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens Insta-DEM Screen Series Manual de usuario

Elite Screens

Elite Screens DE103C82H Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Manual de usuario

Elite Screens

Elite Screens Manual SRM Pro Series Manual de usuario

Elite Screens

Elite Screens CineTension B Series Guía

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación