Elite Screens EDGE FREE Aeon Series Manual de usuario

Rev.070216-MZ

EDGE FREE

Applies to all available screen materials:

Product Description: The Aeon

Series is a fixed frame projection

The EDGE FREE® des

ign resembles a giant size flat

installation option to further enhance the frame appearance and

backlighting kit is available

for added visual appearance

Hardware and Parts List

Please make sure all parts listed below a

re included

A. Elbow joint x 4 pcs

B. Top/Bottom horizontal

fame x 4 pcs

E. Center Support bar x 1-2

F. Wall brackets x

I. M6x12 screw x 2-12pcs J

. M5x50 screws and anchor x

M. Black Tape x 1 bag N. B

ezel trim

www.elitescreens.com

Aeon Series

EDGE FREE

Fixed Frame Projection Screen

User’s Guide

CineGrey 3D EDGE FREE® and

CineWhite

Series is a fixed frame projection

screen that

uses Elite’s EDGE FREE

ign resembles a giant size flat

panel TV display. The Aeo

n includes a

installation option to further enhance the frame appearance and

absorb projector overshoot

for added visual appearance

re included

before installation.

B. Top/Bottom horizontal

fame x 4 pcs

C. Left/Right vertical

frame x 2 pcs

F. Wall brackets x

2-3 pcs G. M6 screw x 2-12 pcs

H. M5x15 screw x

. M5x50 screws and anchor x

6 pcs

K. Rubber hammer x 1 pc

ezel trim

x 6 pcs O. Corner Support Bar

(180”-200”) x 4 pcs

Fixed Frame Projection Screen

CineWhite

™ EDGE FREE®

uses Elite’s EDGE FREE

™ technology.

n includes a

n ultra-thin trim as an

absorb projector overshoot

. An optional LED

D. Center joints x 2 pcs

H. M5x15 screw x

24 pcs

L. Screwdriver x 1 pc

O. Corner sleeve x 4 pcs

Rev.070216-MZ www.elitescreens.com 2

Frame Assembly

1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H).

2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.

3. Repeat steps 1 and 2 for assembling the second horizontal frame.

Push

4. Insert and slide in oneM6 screws (G) through the channel located on the back each horizontal frame.

5. Insert the elbow joint (A) into each end of the horizontal frames (B)as shown below.

Horizontal long frame (B)

ElbowJoint

(A)

ElbowJoint

(A)

Horizontal long frame

Place one M6 hex screw (G) in the center for attaching the center support bar (E)

Face up

M6 hex screws (G)

Horizontal frame

Center Joints

Top right Frame Top left Frame

Note: For models 180” and above, insert and slide in four M6 screws

(two on each frame) through the channel located on the back of each

horizontal frame section (top/bottom). Insert two M6 screws on each

vertical frame section (left/right).

Push

Rev.070216-MZ www.elitescreens.com 3

6. Insert the two vertical short frames(C) into the elbow joint (A).

7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.

Horizontal long frame (B)

Vertical short frame (C)

Horizontal Long frame (B)

push

Note: For models 180” and above,

ensure two M6 screws (G) are

inserted on each vertical frame

before proceeding to step 7.

Face up

Rev.070216-MZ www.elitescreens.com 4

8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the

M5x15 Screws (H).

Screen Material Installation

1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position. The

back side of the screen material should be placed upwards.

Note: The back side of the material has the velcro borders all around the edges.

2. Carefully and gently place the assembled frame on top the screen material as shown below. Make sure to not allow

the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

Four corners join correctly to form a perfect

square. Use the included screwdriver (L) to

fasten the Mx15 screws (H) into each corner

by aligning the frame screw holes to the

holes in the elbow joint (A).

Screen material back facing up

Screen material comer

Rev.070216-MZ www.elitescreens.com 5

3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following

order A→B→C→D (see instructions below for details).

Attach the screen material to the corners as shown below.

4. After all four corners have been attached; please check whether the frame corners are wrapped by the screen

material. If not, please loosen the velcro connection and repeat the above steps so the frame is not exposed.

Note: The black shaded part represents the velcro on the frame. That Velcro

end will ultimately attach with the other velcro end on the screen material.

Note:

Represents the

screen material

2) Fold over and attach

material to the velcro

strip of the frame.

3) Fold over second side

and attach to frame

4) Repeat until all four

sides are done in the

order A, B, C, D

1) Stretch the screen

material in the direction

of the arrowhead.

C A

B D

Rev.070216-MZ

Proceed to attach the rest of the material to the frame as described in the illustrations below.

Grasp the middle

of the

material and attach it to the velcro

strip on the frame

Attach in the following sequence

www.elitescreens.com

Proceed to attach the rest of the material to the frame as described in the illustrations below.

Lay the Velcro end on the screen

material over the Velcro

frame and keep it within the edge.

Proceed

in the following sequence

below ①

②

The key is to attach within the

middle sections of 1 and 2. Then

continue attaching the remaining

unattached areas.

Repeat

the

remaining three sides in the

sequence A, B, C,

show below.

of the

screen

material and attach it to the velcro

Attach in the following sequence

: a-b-c-d

Proceed to attach the rest of the material to the frame as described in the illustrations below.

Lay the Velcro end on the screen

material over the Velcro

end of the

frame and keep it within the edge.

in the following sequence

②

The key is to attach within the

middle sections of 1 and 2. Then

continue attaching the remaining

unattached areas.

the

same steps on

remaining three sides in the

sequence A, B, C,

and then D as

Rev.070216-MZ www.elitescreens.com 7

6. If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material.

Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure

prolonging the life of the screen material.

Screen Material Removal

1. Detach the velcro from the frame.

2. Gently pull back the material to release it from the velcro connections on the corners

Support bar installation (for models under 180”):

1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar

with the M6 hex screws (G) on the top and bottom frames. Then fasten with the M6x12 screws (I).

Move the M6 hex screw (G) to the middle area of the frames.

Align the M6 screws

with the two holes.

Pull back the screen material from

the velcro connection along the

edges of the frame to detach it.

Center Support bar

Rev.070216-MZ

Support bar installation

(for models

1. Position the

center support bar (E)

hole on each end of the support bar with the

Then fasten with the

M6x12 screws (I).

2. Position the

Corner support bars (

below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located

on the vertical and horizontal frame sections. Then fasten with the

Move the

M6 hex screw (

Corner Support Bar

Figure 1

Center Support bar

Align the M6

screws with the

two holes on the

Corner Support

Bars.

www.elitescreens.com

(for models

180” and above):

center support bar (E)

and M6 hex screws (G)

in the areas of the frame shown in fig 1. Align the

hole on each end of the support bar with the

M6 hex screws (G) loca

ted at the top and bottom frame

M6x12 screws (I).

Corner support bars (

O) and M6 Hex screws (G)

in the areas of the frame as shown

below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located

on the vertical and horizontal frame sections. Then fasten with the

M6x12 screws (I

M6 hex screw (

G) to these areas of the frame.

Align the M6 Screws

with the two holes

located on the Center

Support Bar.

Corner Support Bar

in the areas of the frame shown in fig 1. Align the

ted at the top and bottom frame

sections.

in the areas of the frame as shown

below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located

M6x12 screws (I

Rev.070216-MZ www.elitescreens.com 9

Notice to Installer:

Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D Angular

Reflective ALR (Ambient Light Rejecting) Screen.

Make sure to follow these instructions in order for the CineGrey 3D to perform correctly.

•Angular-Reflective material is not compatible with ultra/short-throw projectors

•Minimum lens throw ratio 1.5x image width

•Ambient light must not come from the same direction as the projector

Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it is important to position

the projector so that the viewer will get the best possible image.

Step 1: Establish the general “eye level” of the viewers

Step 2: Set the appropriate projection level

Step 3: Adjust the screen height level and projection angle

Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Rev.070216-MZ www.elitescreens.com 10

Edge trim Installation

Included is an ultra-thin black edge trim that provides an elegant bezel finish

1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. Align the

tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to the center of

the top and bottom of the screen material.

Figure 1

2. Without removing the adhesive tape, place all the trim pieces along the edge of screen material. Adjust the trim

pieces so that the four corners are evenly aligned. (Note: The Elite logo should be positioned on the bottom right).

Refer to Figure 2 below for a visual reference.

Figure 2

NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The back of the

material should be labeled with a DOWN sticker to indicate the material is facing in the down position. The Elite

Screens logo should be installed on the DOWN side

3. After properly aligning all trim pieces, carefully remove trim piece A (see Figure 3 below). Remove the inside

backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining

trim pieces in the following order: B-C-D-E-F.

Figure 3 The front side of the frame with trim pieces attached

Edge trim x 6 PCS

Black tape x1pcs

Trim

strip

Screen Material

The black tape

Front Side

Back Side

Plastic corner sleeve x4pcs

x4pcs

The black tape

Otros manuales para EDGE FREE Aeon Series

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens M135XWV2 Manual de usuario

Elite Screens

Elite Screens F100NWH Manual de usuario

Elite Screens

Elite Screens Electric100H Manual de usuario

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Manual de usuario

Elite Screens

Elite Screens DIY Screen Series Manual de usuario

Elite Screens

Elite Screens EZ-Cinema Series Guía de referencia rápida

Elite Screens

Elite Screens Yard Master 2 WraithVeil Dual Series Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens CineTension 2 Dual Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual del propietario

Elite Screens

Elite Screens Osprey Tension Dual Series Manual de usuario

Elite Screens

Elite Screens Raptor Series Manual de usuario

Elite Screens

Elite Screens Saker Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens F100NWH Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens ITE139XW3-E8 Manual de usuario

Elite Screens

Elite Screens Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens Saker Series Manual de usuario

Elite Screens

Elite Screens Starling Tension Series Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens Pop-Up Cinema Series Manual de usuario

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Elite Screens

Elite Screens Elite Home 2 Series Manual de usuario

Elite Screens

Elite Screens SilverFrame 100GH1 Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación