Ekwb EK-XLC PREDATOR 240 Manual de usuario

EK-XLC Predator 240/360

Push-Pull Addon

For EK-XLC Predator units | 1st revision, July 15th 2016

INSTALLATION MANUAL

/ 1 /

This product is intended for installation

only by expert users. Please consult

with a qualiﬁed technician for installa-

tion. Improper installation may result in

damage to your equipment. EK Water

Blocks assumes no liability whatso-

ever, expressed or implied, for the use

of these products, nor their installation.

The following instructions are subject

to change without notice. Please visit

our web site at www.ekwb.com for up-

dates. Before installation of this product

please read important notice, disclosure

and warranty conditions printed on the

back of the box.

Before you start using this product

please follow these basic guide-

lines:

1. Please carefully read the manual

through before beginning with the

installation process!

2. Please remove your Predator unit

from the computer to assure safest

mounting process in order to pre-

vent any possible damages to your

hardware.

3. Please use only the enclosed

screws. Using inappropriate screws

may result in radiator puncture lead-

ing to leakage of the cooling ﬂuid.

All disclosures, notices and warranty conditions are being written on the EKWB

website. Please read terms of use.

/ 2 /

CONTENTS OF THE PACKAGE

Vardar F4-120ER fan

2/3pcs

Cable tie

3/4 pcs

2,5 mm Allen key

1 pcs

M4x6 DIN7984

8/12 pcs M4X10 DIN7984

3/4 pcs

/ 3 /

Y 3-fan splitter adapter

1 pcs (only at360 mm version)

Y 2-fan splitter adapter

1 pcs

/ 4 /

The fans come with dierent ca-

ble leads lenght. This is because

every fan is intended for speciﬁc

position on the Predator unit. The

longer the cable, the further away

from the fan splitter hub is fan

meant to be installed.

Cable lenghts for dierent EK-

XLC Predator versions:

A. 170mm (Predator 240 & 360)

B. 300mm (Predator 240 & 360)

C. 420mm (Predator 360)

Cable lenght

A B C

Fan splitter hub

/ 5 /

PREPARING YOUR PREDATOR UNIT

STEP 1:

It is recommended to remove the

Predator unit out of the chassis. You

can leave the water block installed but

must be careful not to pull/bend the

tubing. That may result to leakage

and damaged hardware. You can also

unplug all the electrical connections

from the predator unit in order to in-

stall the fans comfortably.

STEP 1

/ 6 /

INSTALLING ADDITIONAL FANS

The additional two (With EK-XLC

Predator 240) or three (With EK-

XLC Predator 360) fans should be

installed on the bottom side of the

Predator unit. Do NOT install the

additional fans on top of the stock

ones. That may lead to malfunc-

tioning of the fans. The orientation

of the fans is crucial in order to

achieve the best performance of the

radiator. Install the fans so that they

push the air through the radiator. For

orientation you can also look at the

orientation of the EK logo. It must

be rotated in same direction at both,

upper and lower set of fans. Make

sure to face the cable routing holes

on the fan case to same side as the

already installed ones.

Airﬂow direction

/ 7 /

In order to secure the fans

to the Predator chassis you

should use four (4) M4x6

DIN 7984 screws with the

enclosed Allen key for each

fan unit. If you want to se-

cure the cables to the Pred-

ator unit you should use a

cable tie along with longer –

M4x10 DIN7984 screws in-

stead. (See the detailed pic-

ture below). There is no need

to use a cable tie on every

screw mounting position.

For better understanding

you can look at the cable

management at already in-

stalled fans.

M4x6 DIN

7984 Screws

2,5mm Allen key

Cable tie

M4x10 DIN

7984 Screw

Cable tie

M4x10 DIN

7984 Screw

/ 8 /

ELECTRICAL CONNECTIONS

In order to connect the fans you should

take the enclosed fan splitter adapters.

Please follow the instructions below, de-

pending on the variant of EK-XLC Predator

EK-XLC PREDATOR 240

STEP 1:

Connect the 2 female 4-pin headers from

the fans with the male ones from the Y

2-fan splitter as shown on the picture.

STEP 2:

Connect the Female 4-pin connector

header from the Y fan splitter adapter with

the male one on the fan splitter hub located

on the backside of EK-XLC Predator unit.

The electrical connection is now complete.

STEP 2

STEP 1

Y 2-fan splitter adapter

/ 9 /

EK-XLC PREDATOR 360

STEP 1:

Connect the 3 female 4-pin headers from

the fans with the male ones from the Y

3-fan splitter as shown on the picture.

STEP 2:

Disconnect one fan from the fan splitter

hub located on the backside of EK-XLC

Predator unit. There are 3 4-pin connec-

tors powering the 3 fans and one pow-

ering the pump. You can only disconnect

the fans and leave the connector on the

far right (pump) connected.

STEP 2

STEP 1

Y 3-fan splitter adapter

Pump connector

Otros manuales para EK-XLC PREDATOR 240

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FC 6970 V2 Manual

ekwb

ekwb EK-FC1070 GTX Manual de usuario

ekwb

ekwb EK-FCQK6000 Guía

ekwb

ekwb EK-FC580 DCII Manual

ekwb

ekwb EK-Classic GPU Water BlockRTX 2080Ti D-RGB Manual de usuario

ekwb

ekwb EK-Velocity sTR4 Manual de usuario

ekwb

ekwb SLIM 120 Manual de usuario

ekwb

ekwb Velocity-AMD Manual de usuario

ekwb

ekwb EK-FC R9 Fury X Guía

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Manual de usuario

ekwb

ekwb EK-QuantumX Delta TEC Manual de usuario

ekwb

ekwb EK X Series Manual de usuario

ekwb

ekwb EK-FC670 GTX Backplate Manual

ekwb

ekwb EK-AIO 280 D-RGB Manual de usuario

ekwb

ekwb EXTREME 240 Manual de usuario

ekwb

ekwb EK-FC 780 GTX DCII Series Manual

ekwb

ekwb EK-Quantum Vector FE RTX 3090... Manual de usuario

ekwb

ekwb EK-FC Titan X Guía

ekwb

ekwb EK-FC680 GTX SOC water block Guía

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Manual de usuario

ekwb

ekwb EK-Pro CPU Water Block SP5 Manual de usuario

ekwb

ekwb EK-FC 780 GTX DCII Original CSQ Manual

ekwb

ekwb EK-FC480 GTX Manual

ekwb

ekwb EK-FB RE2 Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-XLC PREDATOR 240 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas