Ekwb EK-Vector Strix RTX 2070 Backplate Guía

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector Strix RTX 2070

Backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of ROG Strix GeForce RTX 2070 graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

EK-Vector Strix RTX 2070 Backplate is very easy to install. First install EK-Vector Strix RTX 2070 series water block according to its installation manual. If you

have it already installed, please check the picture below to see which mounting screws are to be left in their position and which should be removed. Please

remove the six (6) M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector Strix RTX 2070 Backplate features passive cooling of the printed circuit board and its components therefore it is mandatory to install the

enclosed thermal pad. Please install enclosed 1,5mm and 1mm thick thermal pads (Thermal Pad G –1,5mm (120x24) & Thermal pad F –1mm

(120x16)) as shown on the picture below. You may need to trim the excess thermal pad.

Thermal PAD G –1,5mm (120x24mm)

EK-Vector Strix RTX 2070 Backplate

Thermal PAD F –1mm (120x16mm)

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-VECTOR STRIX RTX 2070 BACKPLATE TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over tightening of

the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector Strix RTX 2070 series water blocks. No other 3rd party heat

sinks or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the

computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top

of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible,

EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks

cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During

this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased;

(II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or

used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other

than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not

affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids.

EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee

and not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5x7 AX1

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-Quantum Reflection PC-O11D D5 PWM D-RGB Manual de usuario

ekwb

ekwb 3831109816202 Guía

ekwb

ekwb EK-Quantum Momentum ROG Zenith II Extreme Manual de usuario

ekwb

ekwb EK-FC1080 GTX Backplate Guía

ekwb

ekwb EK-Annihilator Pro ILM Series Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb EK-Quantum Kinetic TBE 120 VTX PWM Manual de usuario

ekwb

ekwb EK-Dual DDC X-Top CSQ Manual

ekwb

ekwb EK-FB ASUS P7P55 KIT Guía

ekwb

ekwb EK-XRES Revo D5 Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Backplate Guía

ekwb

ekwb EK-XTOP D5 Manual

ekwb

ekwb EK-Pro GPU WB RTX 4000 - Ni + Inox Manual de usuario

ekwb

ekwb EXTREME 240 Manual de usuario

ekwb

ekwb EK-FC R9 Fury X Guía

ekwb

ekwb EK-XTOP D5 Guía

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Manual

ekwb

ekwb EK-FC Titan X Guía

ekwb

ekwb EK-FC1080 GTX JetStream Backplate Guía

ekwb

ekwb EK-QuantumX Loophole Distroplate D5 PWM Manual de usuario

ekwb

ekwb EK-FC580 GTX Guía

ekwb

ekwb EK-Loop Manual de usuario

ekwb

ekwb GTX 1080 Ti Aorus Backplate Guía

ekwb

ekwb EK-FC7850 Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-Vector Strix RTX 2070 Backplate Guía

Manuales populares de Hardware de computadora de otras marcas