Ekwb EK-FB ASUS Max4 Extreme Guía

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box or our home page.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus IV Extreme PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all 8 screws holding the original heat-

pipe cooler / backplate assembly to the motherboard’s circuit board.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all

screws securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip,

as shown on sample photo) of the original thermal compound until the components and

circuit board are completely clean. EKWB does not recommend using any liquids for

removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the NF200 (NB) and P67 PCH (SB chips with

for example Arctic Cooling MX-2 ™or MX-4 ™ thermal grease. EKWB recommends

to apply thermal grease in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. Two (2) 90x15x1mm thermal pads are enclosed with your

EK-FB Max4 Extreme water block. You will have to cut the thermal pad in order to cover all

marked surfaces surface. (WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS ON

BOTH SIDES PRIOR TO INSTALLATION.)

P67 Southbridge

NF200

bridge chip

CPU socket

Installation and mounting manual for EK-FB ASUS Max4 Extreme water block:

Mosfets

Apply thermal grease on

Northbridge (NF200) and

Southbridge (P67).

Place 1mm thermal pads here and make

sure all chips are covered.

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs on NB & MOSFET part of the waterblock (thickness 2,1

mm) so the holes are concentric. Use two 3,3mm acetal standoffs on the SB part of the

waterblock to make one 6,6mm standoff. Thermal paste provides enough adhesive force

for standoffs to stay in a place for easier installation. This is a crucial step!

2. PLACING BLOCK OVER MB. Place the motherboard on the inverted water blocks

or vice versa and attach them with enclosed screws as shown. Make sure that

mounting holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the circuit board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block. Block was tested on physical hardware. Due to height variations of chipset some differences may occur. In case you have problem with block

contacts please write to our support mail.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings as shown in picture, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. Please use spacer if you use fitting with G1/4 thread

longer than 5mm. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-FB

Max4 Extreme series water blocks. The use of an market proved algaecide is always recommended for any liquid cooling system. You can use any opening as an inlet/outlet

port.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2.5x6 DIN7985 2 screws M3x12 DIN7985 8 PVC washers

EK-PSC compression fitting

Two 3,3mm

standoffs combined

on the SB part of

the waterblock

2,1mm standoffs

Use two (2) enclosed M3x12 DIN7985

screws on the southbridge part of the

waterblock!

PVC washer

M2.5x6 DIN7985

screw

philips head screwdriver

ROG LED socket

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb 3831109891452 Manual de usuario

ekwb

ekwb EK-Backplate ASUS P6X58D Premium Guía

ekwb

ekwb EK-AIO BASIC 240 Manual de usuario

ekwb

ekwb EK-FC R9 Nano Series Manual

ekwb

ekwb EK-Classic GPU Water Block RTX 3080/3090... Manual de usuario

ekwb

ekwb Barebones Guía

ekwb

ekwb EK-Dual DDC X-Top CSQ Manual

ekwb

ekwb EK-KIT HT Series Manual de usuario

ekwb

ekwb EK-FC 6970 Manual

ekwb

ekwb EK-PRO GPU WB RTX A100 80GB Manual de usuario

ekwb

ekwb EK-FB ASUS Z270E Strix Monoblock Series Manual de usuario

ekwb

ekwb EK-Quantum Magnitude Manual de usuario

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON RGB... Manual de usuario

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Manual

ekwb

ekwb EK-PRO GPU WB RTX 30x0 Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti Strix Manual de usuario

ekwb

ekwb EK-FC R9-290X Original CSQ Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manual de usuario

ekwb

ekwb EK-Quantum RX 6800 Manual de usuario

ekwb

ekwb EK-FC580 GTX Guía

ekwb

ekwb EK-FC 4890 VAPOR X Guía

ekwb

ekwb EK-FB EVGA CLASSIFIED 4-SLI Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB ASUS Max4 Extreme Guía

Manuales populares de Hardware de computadora de otras marcas