Ekwb EK-FB ASUS M8I Monoblock Manual de usuario

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on December 12th 2015

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus VIII IMPACT motherboard

STEP 1: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 2 screws on the back of the power supply board that needs to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution with backplate.

STEP 2: PREPARING YOUR MOTHERBOARD

1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo on right with enclosed EK-TIM Ectotherm thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover the whole

IHS. Applying too much thermal grease will have negative impact on the cooling performance!

2. CUTTING THERMAL PADS. Your block comes with thermal pads which

needs to be trimmed in order to fit the voltage regulation area (MOSFET) on

the motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES

BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Thermal PAD F 1.5mm –(120x16mm) [EAN: 3830046996749]

Installation manual for EK-FB ASUS M8I Monoblock water block

Z170 PCH

(SB)

Mosfets

CPU socket

Thermal pad G–1.0mm

Thermal pad F –1.5mm

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on December 12th 2015

3. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH

SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!

STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB ASUS M8I Monoblock series water block gently to the motherboard or vice versa (as shown on photo

below). Make sure that mounting holes are aligned.

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use four M3x6 DIN7985 and PVC washers with Factory

Backplate. Do not use excessive force when tightening the screws!

B) CPU part: Use four M4x8 DIN7984 with screws and washers.

Tighten the screws in cross pattern using enclosed 2.5mm allen key and philips

screwdriver.

Use the enclosed screws and washers as shown in picture below:

For the EK-FB ASUS M8I Monoblock series water block to operate properly use lower

G1/4 port and MUST BE USED AS THE INLET PORT. EK recommends the use of

EK-ACF fittings. When using fittings other than EK-ACF series please use hose clamps

or appropriate substitute to secure the tubing to the barb. The use of biocide

containing and corrosion inhibiting coolant is always recommended for any liquid

cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver

1mm

1.5mm

Place 1.0mm and 1.5mm thick thermal pads

in larger strips over marked area and make

sure all mosfet chips are covered.

Apply 1mm thermal pad

as shown on the pictures

1mm Theral PAD

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

M3x6 screw

PVC washer

M4x8 screw

Factory Backplate

Check if 2 plastic washers are in

place (factory preinstalled)

Este manual sirve para los siguientes modelos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb Supremacy EVO Manual de usuario

ekwb

ekwb EK-FC750 GTX Series Manual de usuario

ekwb

ekwb EK-D5 Dual TOP CSQ Manual

ekwb

ekwb EK-QuantumX Delta TEC Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-Pro RTX A5000 Manual de usuario

ekwb

ekwb EK-FC 5970 Manual

ekwb

ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni +... Manual de usuario

ekwb

ekwb EK-MSI Z690 Carbon EK X Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb EK-FC7970 DCII Guía

ekwb

ekwb EK-FC I750 SSD Series Manual

ekwb

ekwb EK-Quantum Reflection PC-O11D D5 PWM D-RGB Manual de usuario

ekwb

ekwb EK-Supremacy EVO X99 Series Manual de usuario

ekwb

ekwb EK-FB GA X470 Gaming 7 RGB Manual de usuario

ekwb

ekwb EK-FC460 GS/SONIC Manual

ekwb

ekwb EK Series Manual de usuario

ekwb

ekwb EK-FC690 GTX Backplate Manual

ekwb

ekwb EK-FC Titan XXL Manual

ekwb

ekwb EK-Quantum Convection M.2 NVMe Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manual de usuario

ekwb

ekwb EK-FC980 GTX Original CSQ Series Manual

ekwb

ekwb EK-Supreme HF Guía

ekwb

ekwb EK-FC780 Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB ASUS M8I Monoblock Manual de usuario

Manuales populares de Hardware de computadora de otras marcas