Ekwb EK-FB ASUS CROSSHAIR 3 Manual

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sam

hoto of ASUS CROSSHAIR III FORMULA PCB desi

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 6 screws on the back of

the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Northbridge and Southbridge with

for example Céramique™ thermal compound. Follow this link

http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. One thermal pad (90x15x1 mm) and one thermal pad

(90x7,5x1 mm) are enclosed with your water block. You will have to cut out parts from smaller

thermal pad in order to cover all the surfaces that are left exposed on mosfets. (WARNING:

DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow.

(PLEASE REMOVE FOIL OF THERMAL PADS PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB ASUS CROSSHAIR 3 water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon7thofAugust,2009.

Southbridge

Northbridge

Mosfets

CPUsocket

Apply thermal grease on

Northbridge and Southbridge. Place thermal pads here and make sure

all mosfet chips are covered.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting holes

and place acetal standoffs (thickness 2,5 mm) so the holes are concentric. Thermal paste

provides enough adhesive force for standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water

block or vice versa and attach it with enclosed screws as shown. Make sure that

mounting holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB ASUS CROSSHAIR III FORMULA series

are usually sold with high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an

algaecide is always recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole. Please make sure spacer in installed in hole as shown bellow.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M3x6 DIN7985

Fitting/barb

Spacer

Washer

M3x6 screw

washer

Please use the enclosed insulating

washers on all M3x6mm screws.

Este manual sirve para los siguientes modelos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FC Titan XXL Manual

ekwb

ekwb EK-FC7970 DCII Guía

ekwb

ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario

ekwb

ekwb EK-FC7850 Guía

ekwb

ekwb EK-FC R9-390X TF5 Guía

ekwb

ekwb EK-FC R9 Nano Series Manual

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-TIM Indigo Extreme Manual de usuario

ekwb

ekwb EK-XRES DCP 2.2 Reservoir Manual

ekwb

ekwb EK-FB KIT GA X79 (UD7) Guía

ekwb

ekwb EK-FC R9-295X2 Guía

ekwb

ekwb EK-Momentum MSI Z390 MEG GODLIKE Manual de usuario

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manual de usuario

ekwb

ekwb EK-AIO Elite 360 D-RGB Manual de usuario

ekwb

ekwb EK-MOSFET ASUS M7G Guía

ekwb

ekwb EK-FC 780 GTX DCII Series Manual

ekwb

ekwb EK-Momentum ROG Strix Z390I RGB Manual de usuario

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Manual de usuario

ekwb

ekwb EK-Quantum Kinetic TBE 120 VTX PWM Manual de usuario

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manual de usuario

ekwb

ekwb EK-FC970 GTX TF5 Manual

ekwb

ekwb EK-FC285 GTX Classified Manual

ekwb

ekwb EK-XRES Revo D5 Manual de usuario

ekwb

ekwb EK-FC480 GTX Manual

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB ASUS CROSSHAIR 3 Manual

Manuales populares de Hardware de computadora de otras marcas