Ekwb EK-XRES Revo D5 Manual de usuario

EK-XRES Revo D5

2nd revision, Oct 25th 2016

USER GUIDE

/ 2 /

INSTALLING THE XRES D5 (already done by EK)

61x3mm sealing gasket (OR)

D5 pump body

with motor

Screws M3x12

NU T M74

Pump

holder

Rubber damper

EK-XRES D5

/ 3 /

STEP 1

Install the EK-XRES Revo D5 onto the pump main motor

housing. Make sure you install EK provided 61x3mm o-ring

gasket! Reseat the gasket if needed. You can rotate the

pump and use it in any direction except upside-down to best

suit your installation.

STEP 2

Secure the pump on the EK-XRES Revo D5 using en-

closed M74 Nut.

/ 4 /

ADDITIONAL DAMPER

Top pyramids must be facing UP

/ 5 /

Additional Revo D5 Damper is enclosed. If pump vibrations

are higher than expected additional Revo D5 Soft dump-

er can be used. When replacing damper, take care that top

pyramids are faced up as shown on picture below. In case of

severe tilting of the computer chassis reservoir unit may fall

out of the holder. Additional damper use is recommended in

vertical reservoir unit mount

/ 6 /

USING POLYETHER ANTI-VORTEX FOAM or EK-HD Tube

EK-XRES Revo D5 series pump top / reservoir comes pre-

installed with Anticyclone by default. In case your system

suffers from excessive vortex issues, air bleeding problems

or if the pump is sucking in air you may replace the anticy-

clone with the enclosed polyether foam or EK-HD Tube.

There are two ways to use the polyether anti-vortex foam:

Default conﬁguration PE foam – use whole

This is the default conﬁguration

of EK-XRES Revo D5 series

reservoir.

Use the foam as a whole to re-

place the Anticyclone.

/ 7 /

PE foam – trim to ﬁt recess HD Tub e

Trim the foam to size to ﬁt into

the desired inlet recess on the

EK-XRES Revo D5 main body.

Insert enclosed o-ring 16x2 into

the groove inside center hole

and insert enclosed EK-HD

Tub e 12/ 16 .

/ 8 /

INSTALLING THE RESERVOIR

By default the EK-XRES Revo D5 ships with EK-Revo D5

Holder. This holder is meant to be installed directly on the

computer chassis. User may need to drill 4 (four) Φ5mm

(enclosed sticker with designated holes) holes through the

metal chassis using electric power drill if there are no appro-

priate mounting holes available.

Computer chasis

metal plate

Washer

M4x10 screw

OUTLET

INLET

EK-Revo D5 Holder

/ 9 /

EK recommends users to ﬁnd an appropriate position in your

computer chassis to install the EK-XRES Revo D5 pump as-

sembly. To successfully install the EK-XRES Revo D5 pump/

reservoir assembly please complete the following steps:

1. Find an appropriate position for the unit inside (or perhaps

outside) of your computer chassis; drill mounting holes if

needed. Sticker with designated holes position is enclosed.

Before drilling stick it to the Computer chassis.

2. Attach the EK-Revo D5 Holder to the computer chas-

sis metal frame using enclosed 4 (four) M4x10 DIN7984

screws and PVC washers. Secure the screws using en-

closed Allen key 2.5mm.

3. Insert the rubber damper into the EK-Revo D5 Holder.

Insert the pump into the damper. And secure it using two

M3x12 DIN7984 screws from the side of the holder. Use

enclosed 2mm Allen key. Your installation is now complete.

/ 10 /

AT TACHING FIT TINGS

EK-XRES Revo D5 PWM (incl. pump) series reservoir

pump combo featured 3 (three) G1/4 threaded ports on the

main body of which 1 (one) is inlet and other is outlet. When

reservoir is in upright position outlet port is positioned lower

than inlet port. EKWB recommends using EK-ACF ﬁttings

with the EK-XRES Revo D5 PWM series reservoir pump

combo units. To ensure that the tubes are securely attached

to the barb/ﬁttings, please use hose clamps or an appropri-

ate substitute.

OUTLET INLET

EK-Plug G1/4

EK-ACF Fitting

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FCW9000 Guía

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-Pro CPU Water Block SP5 Manual de usuario

ekwb

ekwb D-RGB Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb Vector 2 FTW3 RTX 3080/90 ABP Manual de usuario

ekwb

ekwb EK-FB GA Z87X-OC Force Guía

ekwb

ekwb EK-FC R9-290X Original CSQ Manual de usuario

ekwb

ekwb EK-FC 5970 Manual

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Guía

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manual de usuario

ekwb

ekwb EK-XTOP Revo Dual D5 Serial Manual

ekwb

ekwb EK-FB ASUS ROG ZE Monoblock Manual de usuario

ekwb

ekwb EK-FC680 GTX SOC water block Guía

ekwb

ekwb EK-FC1080 GTX FTW Guía

ekwb

ekwb R9-290X Series Guía

ekwb

ekwb EK-FB ASUS ROG R6E Monoblock Manual de usuario

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manual de usuario

ekwb

ekwb EK-Vector Strix RTX 2070 Backplate Guía

ekwb

ekwb EK-FC R9-295X2 Manual

ekwb

ekwb EK-FC 6970 Manual

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-DBAY DCP 2.2 Manual

ekwb

ekwb EK-FC 4890 VAPOR X Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-XRES Revo D5 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas