EK-Quantum Vector Strix RTX 3080 D-RGB Manual de usuario

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector Strix RTX 3080/3090

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

REQUIRED TOOLS 5

WATER BLOCK DIMENSIONS 5

WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

REMOVING THE STOCK BACKPLATE 8

CLEANING THE PCB 9

CUTTING AND PLACING THERMAL PADS 9

APPLYING THERMAL COMPOUND 10

INSTALLING THE WATER BLOCK 11

PLACING THE BLOCK ON THE GRAPHICS CARD 11

ATTACHING THE BLOCK TO THE GRAPHICS CARD 11

CHECKING FOR CONTACT 12

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

INSTALLATION OF FITTINGS AND TUBING 13

CONNECTING THE D-RGB LED STRIP 13

TESTING THE LOOP 14

SUPPORT AND SERVICE 15

SOCIAL MEDIA 15

- 4 -

BOX CONTENTS

4 mm

6 mm

8 mm

M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)

M2.5 Nut (2 pcs)

M2,5x6 AX1 Screw (13 pcs)

Allen Key 2.5. mm (1 pc) Thermal Pad F 1.0 mm (5 pcs)

Thermal Grease (1 pc)

M2,5x8 AX1 Screw (2 pcs)

M2,5x4 AX1 Screw (16 pcs)

EK-Quantum Vector Strix RTX 3080/3090 D-RGB M2.5 PVC Washers (16 pcs)

120 mm

16 mm

EK-Plug G1/4 (2 pcs)

Mounting mechanism - You may not need all the screws,

mounting mechanism is universal!

- 5 -

WATER BLOCK DIMENSIONS

293 mm

129 mm

154 mm

142 mm

14,6 mm

16,4 mm

Phillips Head Screwdriver Torx T6 Screwdriver Scissors

REQUIRED TOOLS

- 6 -

WATER BLOCK SPECIFICATIONS AND MAIN PARTS

TO P P L ATE

(PLEXI / ACETAL)

O-RING

176 x 2

M4/M2,5 x 6,6 STANDOFF

M4/M2,5 x 2,5 STANDOFF - SHORT

COLDPLATE (COPPER / NICKEL)

JET

PL AT E

LED

D-RGB STRIP

M4/M2,5 x 2,5

STANDOFF - LONG

M4 x 27 DIN7984 SCREW

TERMINAL (PLEXI / ACETAL)

O-RING 15x1

M4 x 8 DIN7984 SCREW

EK BADGE STANDOUT

(BLACK / WHITE)

Technical Speciﬁcation:

- Dimensions: (LxHxW) - 293x154x16.4mm

- D-RGB (Adressable RGB) cable length: 500mm

- D-RGB LED count: 12

- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)

- 7 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Use the Phillips head screwdriver to remove the three screws from the

GPU bracket side and six screws from the side of the backplate.

After removing all nine screws (marked in the picture), carefully detach

the PCB with the backplate from the stock cooler and disconnect two

cables connected to the PCB.

Always remove the stock cooler slowly - it might be ﬁrmly

glued to the PCB with thermal pads.

For this Step, you will need:

Phillips Head Screwdriver Torx T6 Screwdriver

STEP 1

- 8 -

STEP 2

REMOVING THE STOCK BACKPLATE

Use the Phillips head screwdriver to remove the two screws attaching

the GeForce® RTX™ plate to the backplate.

Remove the nine screws with Phillips and Torx head screwdrivers

and carefully detach the stock backplate from the PCB.

STEP 2

- 9 -

STEP 3

STEP 1

Your GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal pads:

5x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

STEP 1

Thermal Pad F – 1.0 mm (120 x 16 mm)

STEP 3

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

CUTTING AND PLACING THERMAL PADS

120 mm

16 mm

1 mm

- 10 -

Thermal Grease

STEP 2

Strix RTX™ 3080/3090 STEP 2

Once cut to size, thermal pads should be placed on the PCB, as

illustrated below. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the CPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 1

APPLYING THERMAL COMPOUND

For this Step, you will need:

Thermal Pad F 1.0mm

Otros manuales para Vector Strix RTX 3080 D-RGB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de EK-Quantum

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manual de usuario

EK-Quantum

EK-Quantum LGA1700 Manual de usuario

EK-Quantum

EK-Quantum Vector2 Red Devil RX 7900 XTX D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manual de usuario

EK-Quantum

EK-Quantum Velocity 2 D-RGB AM4 Manual de usuario

EK-Quantum

EK-Quantum Momentum ROG Maximus XIII Hero D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Monoblock Series Manual de usuario

EK-Quantum

EK-Quantum Velocity D-RGB - AMD Ryzen Edition Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum EK-Classic GPU Water Block Strix RTX 3070... Manual de usuario

EK-Quantum

EK-Quantum Vector2 Arc A750-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB Manual de usuario

EK-Quantum

EK-Quantum MSI MPG X670E CARBON EK X D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection DK-O5F Left D-RGB Manual de usuario

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manual de usuario

EK-Quantum

EK-Quantum Reflection2 7000D D5 PWM D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum MSI Z590 Carbon D-RGB Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario