EK-Quantum Vector RTX 3080/3090 Backplate Manual de usuario

USER GUIDE

EK-Quantum

Vector XC3 RTX 3080/3090 Active Backplate

This product is intended for installation by expert users only. Please

consult with a qualiﬁed technician. Improper installation may result

in damage to your equipment. EK assumes no liability whatsoever,

expressed or implied, for the use of this product or its installation. The

following instructions are subject to change without notice. Please, read

the manual carefully before beginning with the installation process. For

updates, you can visit our ofﬁcial website www.ekwb.com.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid!

For best results, EK recommends the use of EK-CryoFuel

Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

ACTIVE BACKPLATE DIMENSIONS 5

REQUIRED TOOLS 5

ACTIVE BACKPLATE SPECIFICATIONS AND MAIN PARTS 6

INSTALLING THE ACTIVE BACKPLATE 7

PREPARING THE GRAPHICS CARD 7

CUTTING AND PLACING THERMAL PADS 8

REMOVING THE TERMINAL METAL PLATE 9

ATTACHING THE ACTIVE BACKPLATE 10

INSTALLING FITTINGS AND TUBING 11

CONNECTING THE D-RGB LED STRIP 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

M2.5x8 AX1 Screw (8 pcs)

8 mm

120 mm

24 mm

120 mm

24 mm

120 mm

24 mm

BOX CONTENTS

Allen Key 2.5 mm (1 pc)

EK-Quantum Vector XC3 RTX 3080/3090 Active Backplate

Thermal Pad G 1.0 mm (3 pcs)

Thermal Pad G 1.5 mm (1 pc) Thermal Pad G 2.0 mm (3 pcs)

Universal Mounting Mechanism – You may not need every

screw from this package.

- 5 -

ACTIVE BACKPLATE DIMENSIONS

273.6 mm

124.2 mm

112.7 mm

150 mm

179 mm

31.5 mm

Phillips Head Screwdriver Scissors

REQUIRED TOOLS

- 6 -

ACTIVE BACKPLATE SPECIFICATIONS AND MAIN PARTS

Technical Speciﬁcations:

Dimensions (L x H x W): 273.5 x 113 x 31.5 mm

D-RGB (Addressable RGB) Cable Length: 500 mm

D-RGB LED Count: 9

D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)

AB TERMINAL

ALU BAC KP L ATE

COLDPLATE (NICKEL)

TOP PL ATE (PLE XI/ACETAL)

EK BADGE

LED D-RGB STRIP

(OPTIONAL)

EK-PLUG G1/4

M4 x 6 DIN7984 SCREW

M4 x 27 DIN7984 SCREW

TERMINAL O-RING 15 x 1 mm

TERMINAL METAL PLATE

ACE TAL

STANDOUT

MAIN O-RING 92 x 2 mm

- 7 -

INSTALLING THE ACTIVE BACKPLATE

STEP 1

PREPARING THE GRAPHICS CARD

First, complete the installation of your EK-Quantum Vector XC3 RTX

3080/3090 water block according to its installation manual.

In case the water block is already installed, remove the seven (7) AX1

screws and their PVC washers, as shown in the image.

EK-Quantum Vector XC3 RTX 3080/3090 Active Backplate comes

with its own terminal, meaning the original terminal, along with two

(2) 15 x 1 O-rings, on the EK-Quantum Vector XC3 RTX 3080/3090

water block has to be removed.

Unscrew the three (3) M4 x 27 DIN7984 screws and detach the

terminal from the water block.

The procedure of terminal detachment is shown in the image.

Attention!

In case the EK-Quantum Vector XC3 RTX 3080/3090

water block is already ﬁlled with coolant, empty the

content of the water block before continuing with this

step. Be careful that the coolant that remained in the

water block does not come in contact with the GPU!

M4 x 27 DIN7984

SCREW

ORIGINAL GPU

TERMINAL

O-RING 15 x 1

STEP 1

- 8 -

STEP 3

Once cut to size, thermal pads should be placed on the backplate,

as illustrated below.

3080 Version

Thermal Pad G 1.5 mm

Thermal Pad G 2.0 mm STEP 3

STEP 2

CUTTING AND PLACING THERMAL PADS

Your backplate comes with thermal pads that have to be cut into

smaller pieces to cover all the VRM components. EK made sure to

provide you with more than an adequate quantity of thermal pads to

complete this Step.

You must remove the protective foil from both sides of the

thermal pad before installation.

Replacement thermal pads:

3x Thermal PAD G 1.0 mm - (120 x 24 mm) – EAN: 33830046996770

1x Thermal PAD G 1.5 mm - (120 x 24 mm) – EAN: 3830046996787

3x Thermal PAD G 2.0 mm - (120 x 24 mm) – EAN: 3830046996794

STEP 2

120 mm

24 mm

1 mm

Thermal PAD G 1.0 mm (120 x 24 mm)

120 mm

24 mm

1.5 mm

Thermal PAD G 1.5 mm (120 x 24 mm)

120 mm

24 mm

2 mm

Thermal PAD G 2.0 mm (120 x 24 mm)

- 9 -

STEP 4

REMOVING THE TERMINAL METAL PLATE

The Metal plate attached on the Terminal is meant as a precaution,

to secure the two O-rings to prevent them from falling out of their

sockets during transport and handling. Before the installation of

the Active Backplate, this metal plate has to be removed. Unscrew

the three (3) M4 x 27 DIN7984 screws with the provided 2.5 mm

Allen Key shown on the picture. Keep the screws as they will be

needed in the upcoming step, unlike the metal plate which will not

be needed anymore.

STEP 4

M4 x 27 7984DIN SCREW

TERMINAL METAL PLATE

3090 Version

Thermal Pad G 1.0 mm

Thermal Pad G 1.5 mm

Thermal Pad G 2.0 mm STEP 3

- 10 -

Place the active backplate on the PCB and make sure all holes are

aligned. Position an M2.5 x 8 AX1 screw into each of the seven (7)

mounting holes (as shown in the image) and tighten them evenly

with a Phillips head screwdriver.

To avoid using excessive force, you can easily loosen up the three

(3) M4 x 27 7984DIN screws pre-installed on the terminal, but be

careful that two (2) 15 x 1 O-rings remain in their terminal slots.

Also, do not forget to tighten the three (3) loosed M4 x 27 7984DIN

screws back after attaching the Active Backplate.

Then, position the three (3) M4 x 27 7984DIN screws that were

detached from the GPU water block terminal into each of the three

(3) mounting holes (as shown in the image) and tighten them evenly

with the provided 2.5 mm Allen Key.

Do not use excessive force!

CAUTION: When placing the Active Backplate on the PCB,

the two inserted 15 x 1 O-rings must remain inside their

terminal slots. Wrongly positioned O-rings can cause leaks!

STEP 5

M2.5 x 8 AX1 SCREW

M4 x 27 DIN7984 SCREW

STEP 5

ATTACHING THE ACTIVE BACKPLATE

First, make sure the two (2) 15 x 1 O-rings are IN terminal

slots, as shown in the image.

Otros manuales para Vector RTX 3080/3090 Backplate

Tabla de contenidos

Otros manuales de Hardware de computadora de EK-Quantum

EK-Quantum

EK-Quantum Vector2 XC3 RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector RTX 3080/3090 Backplate Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manual de usuario

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manual de usuario

EK-Quantum

EK-Quantum Vector Strix RTX 3070 Backplate Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector FE RTX 3090 Ti D-RGB + Backplate Manual de usuario

EK-Quantum

EK-Quantum Vector Master RTX 4090 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector Strix RTX 3070 Backplate Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection2 PC-O11D XL D5 PWM D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection2 PC-O11D XL D5 PWM D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manual de usuario

EK-Quantum

EK-Quantum Vector2 Arc A750-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

EK-Quantum

EK-Quantum Velocity D-RGB - AMD Ryzen Edition Manual de usuario

EK-Quantum

EK-Quantum MSI MPG X670E CARBON EK X D-RGB Manual de usuario

EK-Quantum

EK-Quantum Reflection2 V3000 Plus D5 PWM D-RGB Plexi Manual de usuario

EK-Quantum

EK-Quantum Vector RX 6700XT Backplate Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manual de usuario

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario