Edwards Barocel 7025 Manual de usuario

W602100880_A Original Instructions

Barocel 7025 Gauge

INSTRUCTION MANUAL

edwardsvacuum.com

W602100880_A - Copyright notice

Page 2

Trademark credits

Edwards and the Edwards logo are trademarks of Edwards Limited, Innovation Drive,

Burgess Hill, West Sussex RH15 9TW.

VCR® Swagelok Marketing Co.

Disclaimer

The content of this manual may change from time to time without notice. Edwards accepts no

liability for any errors that may appear in this manual nor does it make any expressed or

implied warranties regarding the content. So far as is reasonably practicable Edwards has

ensured that its products have been designed and constructed so as to be safe and without

risks when properly installed and used in accordance with Edwards operating instructions.

Edwards accepts no liability for loss of profit, loss of market or any other indirect or

consequential loss whatsoever.

Product warranty and limit of liability are dealt with in Edwards standard terms and conditions

of sale or negotiated contract under which this document is supplied.

You must use the Barocel 7025 as described in this manual. Read this manual before you

install, operate and maintain the Barocel 7025.

P20010230A

CE Declaration of Conformity

The following product

List products here including –

•Barocel 7025m Series Capacitance Manometer W6011*

•Barocel 7025 Series Capacitance Manometer W6021*

•Barocel 7045 Series Capacitance Manometer W6032*

•Barocel 7100 Series Capacitance Manometer W6033*

Is in conformity with the relevant requirements of European CE legislation:

2014/30/EU

Electromagnetic compatibility (EMC) directive

2011/65/EU

Restriction of certain hazardous substances (RoHS) directive

as amended by Delegated Directive (EU) 2015/863

Based on the relevant requirements of harmonised standards:

EN 61010-1:2010

Safety requirements for electrical equipment for measurement, control and laboratory

use. General requirements

EN 60529:1991 +

A2:2013

Specification for degree of protection provided by enclosures (IP code)

– IP code 30

EN 61326-1:2013

Electrical equipment for measurement, control and laboratory use. EMC requirements.

General requirements

Class B Emissions, Industrial Immunity

This declaration, based on the requirements of the listed Directives and EN ISO/IEC 17050-1, covers all product

serial numbers from this date on: 6th June 2019.

Larry Marini – Senior Technical Manager

Eastbourne

Andy Marsh – General Manager

Eastbourne

Edwards Ltd

Innovation Drive

Burgess Hill

West Sussex

RH15 9TW

This product has been manufactured under a quality management system certified to ISO 9001:2015

Additional Legislation and Compliance Information

EU RoHS Directive: Material Exemption Information

This product is compliant with no Annex III or IV Exemptions

EU REACH Regulation Compliance

This product is a complex article which is not designed for intentional substance release. To the best of our knowledge

the materials used comply with the requirements of REACH. The product manual provides information and instruction to

ensure the safe storage, use, maintenance and disposal of the product including any substance-based requirements.

Article 33 Declaration

This product does not knowingly or intentionally contain Candidate List Substances of Very High Concern above 0.1%ww

by article as clarified under the 2015 European Court of Justice ruling in case C-106/14.

ADDITIONAL INFORMATION

材料成分声明

China Material Content Declaration

表示该有害物质在该部件的所有均质材料中的含量低于 GB/T 26572 标准规定的限量要求。

Indicates that the hazardous substance contained in all of the homogeneous materials for this part is

below the limit requirement in GB/T 26572.

Page 3

W602100880_A - Contents

Introduction 7

Product identification .................................................................................................... 7

Intended use .................................................................................................................. 7

Function ......................................................................................................................... 7

Before using this gauge .................................................................................................. 7

Safety symbols ............................................................................................................... 7

Safety precautions .........................................................................................................7

Liability and warranty .................................................................................................... 8

Technical data 9

Dimensions ................................................................................................................... 11

Analogue measurement signal versus pressure .......................................................... 12

Installation 13

Vacuum connection ..................................................................................................... 13

Electrical connection .................................................................................................... 14

Operation 16

Displays ........................................................................................................................16

To zero the gauge ........................................................................................................ 16

<ZERO> Adjustment ........................................................................................... 17

<ZERO> Adjustment with ramp function ........................................................... 18

Switching Functions ..................................................................................................... 19

Adjusting the setpoints ...................................................................................... 20

Activating the factory setting (factory reset) ............................................................... 21

Uninstallation 22

Maintenance and repair 23

Return the equipment for service 24

Disposal 25

Separating the components ......................................................................................... 25

Contents

cg/0132/01/18

This page has been intentionally left blank.

Page 4

W602100880_A - Contents

Page 5

W602100880_A - List of Figures

Figure 1: Dimensions .............................................................................................................. 11

Figure 2: Analogue measurement signal versus pressure ...................................................... 12

Figure 3: Connect the gauge to the system ............................................................................ 14

Figure 4: Sensor cable ............................................................................................................ 15

Figure 5: Gauge display .......................................................................................................... 16

Figure 6: Measurement signal (Pressure p) ........................................................................... 20

List of Figures

Page 6

W602100880_A - List of Tables

Table 1: General ....................................................................................................................... 9

Table 2: Output signal .............................................................................................................. 9

Table 3: Gauge identification ................................................................................................... 9

Table 4: Switching functions .................................................................................................... 9

Table 5: Electrical ................................................................................................................... 10

Table 6: Materials exposed to vacuum .................................................................................. 10

Table 7: Environmental .......................................................................................................... 11

List of Tables

Page 7

W602100880_A - Introduction

Introduction

Product identification

Specify the information given on the gauge nameplate in all communications with Edwards.

Intended use

The Barocel 7025 gauge is intended for absolute pressure measurement of gases in their

respective pressure ranges, see Installation on page 13. The unit is clean room compliant and

double protected against contamination.

The gauges belong to the Barocel 7000 series and can be operated in connection with an

Edwards TIC controller or another applicable unit.

Function

The Barocel 7025 gauge has a capacitive sensor element made of aluminium oxide ceramics

and electronics which convert the capacitance into a direct current (d.c.) voltage output

signal.

The output signal is linear to the measured pressure and independent of the gas type.

Before using this gauge

Make sure that the model is the same as you ordered and no damage occurred during

shipment.

Read this instruction manual before you install, operate, inspect, or service this gauge to

familiarize yourself with safety precautions, specifications and operations.

Safety symbols

Important safety information is highlighted as WARNING and CAUTION instructions. Obey the

safety instructions.

The use of warnings and cautions is defined as:

Safety precautions

Obey the applicable regulations and follow the necessary precautions for the process

media used. Reactions with the gauge materials are possible.

WARNING:

Warnings are given where failure to obey the instruction could result in injury or death to

people. The actual symbol shown will change and refer to the applicable hazard.

CAUTION:

Cautions are given where failure to obey the instruction could result in minor injury or

damage to the equipment, associated equipment or process.

Page 8

W602100880_A - Introduction

Obey the applicable regulations and follow the necessary precautions for the work

you do. Obey the safety instructions in this document.

Before you start work, find out if any vacuum components are contaminated. Obey

the applicable regulations and the necessary precautions when you handle

contaminated parts.

Ensure all other users are aware of the safety instructions.

Liability and warranty

Edwards accepts no liability and the warranty becomes non applicable if the end user or third

parties:

Ignore the information in this document

Use the gauge in a non-agreeable manner

Make any kind of interventions (modifications, alterations, etc.) on the gauge

Use the gauge with accessories not listed in this instruction manual.

The customer assumes the responsibility along with the process media used.

Gauge failures because of contamination are not included in the warranty.

Otros manuales para Barocel 7025

Tabla de contenidos

Otros manuales de Bomba de agua de Edwards

Edwards

Edwards nXR30i Manual de usuario

Edwards

Edwards EXTPX Series Manual de usuario

Edwards

Edwards GV Series Manual de usuario

Edwards

Edwards XDD1 115 V AC Manual de usuario

Edwards

Edwards EXT70/70200 Manual de usuario

Edwards

Edwards RV3 Manual de usuario

Edwards

Edwards nES40A Manual de usuario

Edwards

Edwards xds35i Manual de usuario

Edwards

Edwards EH500 Manual de usuario

Edwards

Edwards nEXT 730D Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards EXT555H Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards E2M0.7 Manual de usuario

Edwards

Edwards E1M5 Manual de usuario

Edwards

Edwards EH500T4 T3 Series Manual de usuario

Edwards

Edwards STP-L301 Series Manual de usuario

Edwards

Edwards EDS 065 Manual de usuario

Edwards

Edwards STP-XF813 Series Manual de usuario

Edwards

Edwards CDX1000 Manual de usuario

Edwards

Edwards XDS100B Manual de usuario

Edwards

Edwards A505-23-825 Manual de usuario

Edwards

Edwards EXT400/200/30H Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario