DRYWISE 600591440003 Manual de usuario
PRE-HEATER ADD-ON
FOR DRYWISE DRYER
On-demand, repeatable and reliable lament drying
USER MANUAL
Table of contents
1. Introduction 5
1.1. Intended use of Pre-heater for Drywise dryer
1.2. General disclaimer
2. Safety 6
2.1. General safety information
2.2. Health and safety
3. The Drywise Pre-Heater add-on 7
3.1. Main components
3.2. Specications
4. Installation 8
4.1. Unboxing
4.2. What’s in the box
4.3. Hardware installation and rst interaction
5. Operation 10
5.1. Recommendations
5.2. Material compatibility
6. Maintenance 11
7. Warning Message Screens 11
5.1. The drying process (normal operation)
6.1. Recommendations
7.1. Pre-Heater not detected
8. Warranty 12
8.1. General
8.2. Conditions
8.3. Notication
8.4. Exclusions
8.5. Applicable law and competent court
Drywise Pre-Heater User Manual 5
1.1. Intended use of Pre-heater for Drywise dryer
The Drywise Pre-Heater add-on is designed and built for use in combination with
Drywise Inline Filament Dryer. The Drywise unit is intended to facilitate the printing
with hygroscopic materials, from short to very long prints.
When used with the Drywise Inline Filament Dryer, the Drywise Pre-Heater add-on
delivers a more exible, efcient and reliable solution for handling and processing
laments. The Drywise Pre-heater expands the material compatibility offered by
Drywise, by pre-treating the lament before it is fed into the Drywise dryer. The
attachment is essential for reliable and consistent drying of specic material types
prior to drying. These materials include carbon and glass ber lled materials and
other specic material types. Check https://drywise.co/materials for the latest list of
compatible materials.
1.2. General disclaimer
This user manual describes the intended workow for the Drywise Pre-Heater add-on
when used in conjunction with a Drywise Inline Filament Dryer.
Please carefully read and understand the contents of this user manual. Failure to read
the manual may lead to personal injury, inferior results or damage to the Drywise Pre-
Heater, the Drywise dryer, the 3D Printer and/or its peripherals. Make sure that anyone
who uses this device knows and understands the contents of the manual to make the
most out of the Drywise Pre-Heater.
The conditions or methods used for assembling, handling, storage, use, maintenance
or disposal of the device are beyond Thought3D’s control and may be beyond its
knowledge. For this and other reasons, Thought3D does not assume responsibility and
expressly disclaims liability for loss, injury, damage or expense arising out of or in any
way connected with the assembly, handling, storage, use, maintenance or disposal of
the product.
The information in this document was obtained from sources which Thought3D
believes are reliable. However, the information is provided without any warranty,
express or implied, regarding its accuracy.
1. Introduction
Drywise Pre-Heater User Manual6
2.1. General safety information
• Read and understand safety measures before use of the Product.
• Use the product for intended purpose only
• Use the product with caution. The internal components of the product generate
high temperatures that can cause injury. Do not dismantle and reach inside
the product. Allow at least 30 minutes for the product to cool down, before
performing any maintenance or modication.
• Do not modify or change any parts of the product unless the change or
modication is authorised by the manufacturer or this manual.
• Follow standard electrical safety procedures.
• Follow instructions and safety indicators on the screen of the dryer and/or follow
safety warning labels on the product components.
• Install the product to the Drywise drier well. When the device is connected to the
3D printer via lament, the forces of the extruder may pull the device.
• Do not manually pull or push on lament when the product is in operation unless
instructed by the dryer user interface.
• This product is not intended for children.
• Thought3D products (including Drywise Pre-Heater) are not intended for use by
persons with reduced physical and/or mental capabilities, or lack of experience
or knowledge, unless they are supervised or have been given instructions
concerning the use of the product by a person responsible for their safety.
• Do not insert any foreign objects other than lament for FDM/FFF 3D printing
into the pathway of the lament.
2.2. Health and safety
• The product dries third party materials. Please follow the safety procedures of
the manufacturers of such materials
• The product operates with the help of third-party 3D printers. Please follow the
safety procedures of the manufacturers of such devices.
• Third party materials may release volatile organic compounds (VOCs) and/
or ultrane particles (UFPs). It is recommended that the product is set-up in a
well-ventilated area. Please check the safety data sheet of each specic materi-
al for information.
• Thought3D Ltd cannot be held responsible for any adverse effects from the use
and/or performance of these materials.
This guide contains warnings and safety notices:
Provides helpful information to do a task or avoid problems.
Warns against situations that may cause material damage or injury if
the safety instructions are not followed.
2. Safety
Drywise Pre-Heater User Manual 7
3.1. Main components
3.2. Specications
3. The Drywise Pre-Heater add-on
Properties
Device Pre-heater add-on for Drywise Inline Filmanet Dryer
Technology Fused lament fabrication lament pre-processing (FFF)
Filament Diameter 2.85mm
Compatible Material
• Nylon materials and reinforced nylon materials from
main lament brands
• Updated list on https://drywise.co/materials
Connectivity Pogo pins
Physical Dimensions
Dimensions (180*120*80mm)
Net Weight 100g
Shipping Weight around 400g
1. Pre-heater add-on
2. Filament guiding tube
3. Pogo pins electrical connectors
4. Thumbscrew opening
Drywise Pre-Heater User Manual8
Electrical Requirements
Voltage 24 VDC
Power Max. 20W
Warranty Twenty four (24) months in EU countries and twelve (12)
months outside of EU countries.
4.1. Unboxing
In order to respect the environment, we have opted to use mostly cardboard as our
packaging material. Kindly recycle the packaging material or dispose according to
local legislation in order to help reduce the environmental footprint.
Place the box on a solid surface facing the right way up. Remove the packaging tape
and fold out the cardboard aps. Take out the manual and any other leaets. Remove
the add-on and proceed to the installation.
Choose a suitable location to place the Drywise inline lament dryer and the Drywise
Pre-Heater add-on. Install the Drywise dryer on a at, stable surface capable of with-
standing the weight of the system and on which you can safely operate to install the
add-on.
4.2. What’s in the box
4. Installation
ab
a - Drywise Pre-Heater add-on
b - User manual
Drywise Pre-Heater User Manual 9
4.3. Hardware installation and rst interaction
a) Locate the lament input
port
b) Remove the thumbscrew
and the dowel pin
c) Remove input port cover d) Place the Pre-Heater
add-on in place
e) Re-install the dowel pin,
ip close the the Pre-Heater
add-on and secure it with
the thumbscrew
f) The Drywise Pre-Heater
add-on is ready for use.
Drywise Pre-Heater User Manual10
5. Operation
5.1. Recommendations
The Drywise Pre-Heater add-on must be installed to pre-condition a number of
material types, including but not limited to, reinforced nylons and a sub set of nylon
polymers. The add-on ensures that Drywise operates reliably and gives optimum
results with these laments types. All the settings for the add-on are already pre-
saved on the Drywise dryer and no additional input is required from the user.
DO NOT insert a different type of material other than that specic lament instructed
on the dryer and corresponding to that specic prole. Failure to observe this, could
result in damage to the lament and/or the device.
If the lament that you want to use does not have a prole, kindly check online or
reach out for help before trying to test with any other prole. Damage caused to the
device in this way will not be covered by warranty.
Designed for 2.85mm lament only.
5.2. Material compatibility
The Drywise Pre-Heater add-on is compatible with all material types which are
approved for drying with the Drywise in-line lament dryer. If the add-on is not
required for a specic material type it will be automatically disabled by Drywise. With
specic materials which require the add-on, the Drywise dryer will not function unless
the Drywise Pre-Heater is correctly installed and functional.
The Drywise dryer will automatically set the correct settings based on the lament
chosen.
It is essential to install the Drywise Pre-Heater to be able to use Drywise with the
following materials:
• Carbon bre lled nylons
• Glass bre lled nylons
• Luvocom PAHT resin based laments
• Other specic materials as instructed by the Drywise UI.
The list of tested and approved materials is always growing. For an updated list kindly
check our website at drywise.co/materials.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora 3D de DRYWISE
