DMP Electronics Thinline 7300 Series Guía de instalación
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME
CHIME
ZONE
PERIM SLEEP EXIT
INSTTESTOUTPUT
CODE
1 2 3 4
5 6 7 8
9 0 CMD
INSTALLATION AND PROGRAMMING GUIDE
7300 Series Thinline™
Icon Keypad
TABLE OF CONTENTS
About the Keypad ...................................... 1
Features.............................................................................. 1
Card Reader ...................................................................... 1
Keypad Layout ............................................2
Card Reader ..................................................................... 3
Two-Button Panic Keys................................................ 3
Install the Keypad.......................................4
Remove the Cover ......................................................... 4
Wire the Keypad............................................................. 5
When Using an Auxiliary Power Supply .................... 5
Mount the Keypad ......................................................... 7
Program the Keypad ..................................8
Reading the Display...................................................... 8
User Options.................................................................... 8
Installer Options ............................................................10
Access Installer Options ................................................ 10
Configure Panics and User Code Digits ....................11
Run Keypad Diagnostics ................................................12
LCD Segment Test ............................................................12
Test Individual Keys and Card Reads.........................12
Exit Installer Options ....................................................... 12
Reference................................................... 13
End User Training .........................................................13
Shortcut Keys .................................................................13
Programming Menus Items .......................................14
Panic Keys........................................................................14
Icons...................................................................................15
Display Codes.................................................................16
Compliance Requirements...................... 17
Wiring Specifications ..................................................17
Compatibility ............................................ 18
Panel Models...................................................................18
Credentials.......................................................................18
Product Specifications ............................ 19
Certifications............................................ 20
Intertek (ETL) Listed...................................................20
FCC Information ....................................... 21
Industry Canada Information..................22
7300 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 1
ABOUT THE KEYPAD
The DMP 7300 Series Thinline™ Icon Keypads provide an easy to understand icon display
to assist users when arming and disarming an All/Perimeter or Home/Sleep/Away system
or using any of the standard system features. The icons provide immediate recognition of
any system alarm as well as system status.
7300 Series keypads are compatible with XT Series control panels.
Features
All 7300 Series models provide three 2-button Panic keys, a backlit keyboard with easy-
to-read lettering, and an internal speaker. Additionally, the model 7363 keypad provides a
built-in proximity reader designed to read standard HID proximity credentials.
Card Reader
When a proximity credential is presented to the internal reader, a beep tone is heard to
provide an audible acknowledgment of the credential read.
Digital Monitoring Products, Inc | 7300 Series Installation and Programming Guide2
KEYPAD LAYOUT
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME
CHIME
ZONE
PERIM SLEEP EXIT
INSTTESTOUTPUT
CODE
1 2 3 4
5 6 7 8
9 0 CMD
Proximity
Credential Reader
and Backlit Logo
Keypad Display
Select Keys
Panic Keys
Command
(CMD) Key
Back Arrow Key
143
2
Figure 1: 7300 Series Thinline Keypad
7300 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 3
Card Reader
When a proximity credential is presented to the keypad’s backlit logo, a beep tone is
emitted to provide an audible acknowledgment of the credential read.
Two-Button Panic Keys
All keypads oer a panic key function that allows users to send panic, emergency, or
fire reports to the central station in an emergency. Panic keys are enabled in the Installer
Options. Place the icon stickers below the top row select keys as shown in Figure 1.
Note: By default, all 7300 keypads send address 8 to the central station for panic
alarms.
Digital Monitoring Products, Inc | 7300 Series Installation and Programming Guide4
INSTALL THE KEYPAD
Remove the Cover
The keypad housing is made up of two parts: the cover,
which contains the circuit board and components, and
the base.
To separate the keypad cover from the base, insert a
flathead screwdriver into one of the slots on the bottom
of the keypad and gently lift the screwdriver upward.
Repeat with the other slot. Gently separate the cover
from the base and set the cover containing the keypad
components aside. See Figure 2.
1
Figure 2: Separate the
Keypad Housing
Cover
Base
7300 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 5
Wire the Keypad
The 7360 and 7363 keypads are supplied with a 4-wire harness for panel keypad bus
connection. Refer to the following table for wire colors and connections:
WIRE COLOR CONNECT TO PANEL PURPOSE
Red Terminal 7 DC Power
Yellow Terminal 8 Send Data
Green Terminal 9 Receive Data
Black Terminal 10 Ground
When Using an Auxiliary Power Supply
If the current draw for all keypads exceeds the panel output, provide additional
current by adding a Model 505-12 auxiliary power supply:
1. Connect all keypad Black ground wires to the power supply negative terminal.
2. Run a jumper wire from the power supply negative terminal to the panel
common ground terminal.
3. Connect all keypad power (+12 VDC) wires to the power supply positive
terminal.
4. Do not connect the power supply positive terminal to any panel terminal.
For more information, refer to the 505-12 Power Supply Installation Guide (LT-0453).
2
Digital Monitoring Products, Inc | 7300 Series Installation and Programming Guide6
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
Reference Card
Guide Tabs
Surface and Backbox Mounting Holes
Combined 4-square and 3-gang Switch Box Mounting Holes
Keypad Back
Figure 3: Mounting Holes and Wiring Harness
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Teclado de DMP Electronics
DMP Electronics
DMP Electronics Easy Entry 693 Instrucciones de montaje
DMP Electronics
DMP Electronics 532XR Manual de usuario
DMP Electronics
DMP Electronics Thinline 7060 Manual de usuario
DMP Electronics
DMP Electronics 9800INT Series Guía de instalación
DMP Electronics
DMP Electronics 7872 Manual de usuario
DMP Electronics
DMP Electronics 7872 Manual de usuario
DMP Electronics
DMP Electronics 781 Manual de usuario
DMP Electronics
DMP Electronics 9800 Series Guía de instalación
DMP Electronics
DMP Electronics Thinline Series Manual de usuario
DMP Electronics
DMP Electronics 7800 Series Guía de instalación
DMP Electronics
DMP Electronics 9863 Manual de usuario
DMP Electronics
DMP Electronics Thinline 7060 Instrucciones de montaje
DMP Electronics
DMP Electronics Thinline 7463 Guía de instalación
DMP Electronics
DMP Electronics Thinline 7160 Manual de usuario
DMP Electronics
DMP Electronics SC Series Instrucciones de montaje
DMP Electronics
DMP Electronics 7760 Manual de usuario
DMP Electronics
DMP Electronics Thinline Series Manual de usuario
DMP Electronics
DMP Electronics Thinline Series Guía de instalación
DMP Electronics
DMP Electronics 691 Manual de usuario
DMP Electronics
DMP Electronics 9800 Series Guía de instalación
