DMP Electronics 7872 Manual de usuario

INSTALLATION GUIDE

7800 Series

Graphic Touchscreen Keypad

TODAY

WEDNESDAY

98 77

HI LO

CURRENT

98 77

HI LO

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

Description

DMP Graphic Keypads oer ﬂexible features and functionality in a stylish design. Each

keypad provides:

• AC Power/Armed LED

• Simple harness connection to 4–wire keypad bus

• Full color touchscreen display

• Micro SD card slot for customized logo

• Internal speaker

• Icon-driven operation

Model 7872

The Model 7872 keypad provides four fully programmable Class B, Style A, supervised,

power limited protection zones and a built–in proximity card reader designed to read

DMP/HID proximity credentials.

Model 7873

The Model 7873 keypad provides four fully programmable Class B, Style A, supervised,

power limited protection zones and a built–in proximity card reader designed to read

DMP/HID proximity credentials. The Model 7873 keypad also provides a door strike relay

and allows Wiegand input from external card readers.

7800 Series Graphic Touchscreen Keypad Installation Guide

Installing the Keypad

All DMP keypad housings are designed to easily install on any single–gang switch box or ﬂat

surface. Figure 3 shows the keypad housing base mounting hole locations.

Wiring Speciﬁcations for Keypad Bus

When planning a keypad bus installation, keep in mind the following speciﬁcations:

1. DMP recommends using 18 or 22–gauge, unshielded wire for all keypad and

LX–Bus circuits. Do not use twisted pair or shielded wire for LX–Bus and keypad

bus data circuits. To maintain auxiliary power integrity when using 22–gauge wire

with a Model 7872 or 7873, do not exceed 225 feet. When using 18–gauge wire, do

not exceed 500 feet. Install an additional power supply to increase the wire length

or add devices.

2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of

the wire gauge. This distance can be in the form of one long wire run or multiple

branches with all wiring totaling no more than 2,500 feet. As wire distance from

the panel increases, DC voltage on the wire decreases.

3. Maximum number of devices per 2,500 feet circuit is 40.

Note: Each panel allows a speciﬁc number of supervised keypads. Add additional

keypads in the unsupervised mode. Refer to the panel Installation Guide for the

speciﬁc number of supervised keypads allowed.

Installing the Keypad

4. Maximum voltage drop between the panel (or auxiliary power supply) and any

device is 2.0VDC. If the voltage at any device is less than the required level, add

an auxiliary power supply at the end of the circuit. When voltage is too low,

the devices cannot operate properly. Refer to the LX–Bus/Keypad Bus Wiring

Application Note (LT-2031) for more information. Also see the 710 Module

Installation Sheet (LT-0310).

Keypad Speciﬁcations

Model Normal/

Standby

Current Alarm Current Four

Zones

Internal

Prox

Reader

Wiegand

Input

Internal

Door

Strike

Relay

7872 130mA + 1.6mA

per active zone

165mA + 2mA

per active zone X X

7873 130mA + 1.6mA

per active zone

165mA + 2mA

per active zone X X X X

Speciﬁcations

Operating Voltage 12VDC

Dimensions 5.8” W x 4.135” H x 0.6” D

Compatibility

All keypads are compatible with XR150/XR550 Series and XT30/XT50 Series panels.

Installing the Keypad

Accessories

Keypad Wiring Harness

300-7800-12ADPT 12-Wire Harness adapter

300-7800-5 5-Wire Harness

300-7800-12 12-Wire Harness

Proximity Credentials

1306P Prox Patch™

1306PW Prox Patch™ 26-Bit

1326 HID ProxCard II® Card

1386 HID ISOProx II® Card

1346 HID ProxKey II® Access Device

Proximity Readers for 7873 keypads

PP-6005B ProxPoint® Plus 30mA Standby 75mA Peak

MP-5365 MiniProx™ 20mA Standby 110mA Peak

PR-5455 ProxPro II® 25mA Standby 125mA Peak

TL-5395 Thinline™ II® 20mA Standby 115mA Peak

Keypad Mounting

695-7800 In Wall Mount Backbox

698-7800 Plastic Keypad Wall Cover

699-7800 Keypad Deskstand with Cord

Installing the Keypad

Remove the Cover

The keypad housing is made up of two parts: the cover, which

contains the circuit board and components, and the base. Use the

following steps and Figure 1 to separate the keypad cover and base:

1. Insert a ﬂat screwdriver into one of the slots on the bottom of

the keypad and gently lift the screwdriver handle toward you

while pulling the halves apart. Repeat with the other slot.

2. Using your hands, gently separate the front from the base and

set the cover and components aside.

Harness Wiring

1. Firmly grasp the wires near the base and hold the outside

edges of the keypad housing. Line up the red and yellow

wires with the guides on the board to inset the connector

into the J5 keypad terminal. See Figure 2.

Note: Do not remove the keypad housing to install the wiring

harness.

2. Observe wire colors when connecting the red, yellow, green,

and black wires to the keypad bus:

• Connect red wire to Panel Terminal 7

• Connect yellow wire to Panel Terminal 8

• Connect green wire to Panel Terminal 9

• Connect black wire to Panel Terminal 10

Figure 2: Keypad Back Showing

Wiring Harness Assignments

Graphic

Keypad

Building Wall

Insert small

screwdriver and

lift to remove

cover.

Do not twist.

Figure 1:

Removing the Keypad Cover

Y/W

Installing the Keypad

Zone Inputs (Standard)

1. Zone 1 – Brown White/White Brown

2. Zone 2 – Red White/White Red

3. Zone 3 – Orange White/White Orange

4. Zone 4 – Yellow White/White Yellow

Zone Inputs (Access Control – 7873)

1. Zone 1 – Brown White/White Brown

2. Zone 2 – Red White/White Red (Zone 2 Bypass)

3. Zone 3 – Orange White/White Orange (REX)

4. Zone 4 – Yellow White/White Yellow

Using the 7800 Keypad for Access Control (7873)

Card Readers

When a proximity credential is presented to an internal or external reader, a beep tone

is heard and the Power/Armed LED blinks. This provides both an audible and visual

acknowledgment of the credential read.

Internal Access Control Reader

The 7873 and 7872 keypads provide a built-in proximity card reader designed to read

DMP/HID 1300 Series proximity credentials.

Using the 7800 Keypad for Access Control

1K EOL

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black– Ground

Red – Keypad Power

– Zone 1

– Zone 2

– Zone 3

– Zone 4

Zones 1 to 4

7872 / 7873 Keypads

External Card

Reader

Green/White – Connect Reader Data 0

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

All Keypads

Red

Black

Green

Yellow

Surface and Backbox

Mounting Holes

Keypad Back

Figure 3: 12 VDC Reader Wiring

Using the 7800 Keypad for Access Control

External Access Control Reader

To accept Wiegand data input from other external card readers, connect a 12VDC external

reader to the 7873 keypad. Connect the red and black power wires from the reader to

the power wires from the panel. These connect in parallel with the keypad power wires.

Connect the Reader (Data 1) wire to the white wire on the 5–wire keypad harness. Connect

the Reader (Data 0) wire to the green/white wire on the 5–wire keypad harness. See

Figure 3.

Magnetic Lock and Door Strike Wiring

The 7873 keypad provides one internal programmable

Form C single pole, double throw (SPDT) relay for

controlling door strikes or magnetic locks. Three wires

on the 5-wire harness, violet normally closed (N/C),

gray common (COM), and orange normally open

(N/O), allow you to connect devices to the relay. The

Form C relay draws up to 15mA of current and the

contacts are rated for 1 Amp at 30VDC maximum,

resistive.

Wiring the 333 Suppressor

One Model 333 Suppressor is included with

the 7873 keypad. If the device being controlled

by the relay is connected to the N/O and C

wires, install the suppressor on the N/O and

C wires. If the device is connected to the N/C

and C wires, install the 333 on N/C and C

wires. Refer to Figure 4a and 4b.

Using the 7800 Keypad for Access Control

1K EOL

Green/White –

Connect Reader

Data 0

White– Connect

Reader Data 1

Orange – N/O

Gray – Common

Violet – N/C

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black– Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3

– Zone 2

– Zone 1

All Keypads

Zones 1 to 4

7800 Series Keypads

Model 333 Supressor

Common

–+

Magnetic Door Lock

DMP 505-12

Power Supply

Normally

Open

Normally

Closed

Surface and Backbox

Mounting Holes

Keypad Back

Figure 4a: Magnetic Lock Wiring

Otros manuales para 7872

Tabla de contenidos

Otros manuales de Teclado de DMP Electronics

DMP Electronics

DMP Electronics 9800 Series Manual de usuario

DMP Electronics

DMP Electronics XTL Series Manual de usuario

DMP Electronics

DMP Electronics 9863 Manual de usuario

DMP Electronics

DMP Electronics 7800 Series Guía de instalación

DMP Electronics

DMP Electronics Thinline 7160 Manual de usuario

DMP Electronics

DMP Electronics 699 Manual de usuario

DMP Electronics

DMP Electronics easy entry 791 Manual de usuario

DMP Electronics

DMP Electronics XR5FC Manual de usuario

DMP Electronics

DMP Electronics 791 Easy Entry Instrucciones de montaje

DMP Electronics

DMP Electronics Aqualite 7560A Manual de usuario

DMP Electronics

DMP Electronics Thinline Series Guía de instalación

DMP Electronics

DMP Electronics Security Command 690 Manual de usuario

DMP Electronics

DMP Electronics Thinline 7463 Guía de instalación

DMP Electronics

DMP Electronics 9000 Series Manual de usuario

DMP Electronics

DMP Electronics 9800INT Series Guía de instalación

DMP Electronics

DMP Electronics Security Command 670-A Manual de usuario

DMP Electronics

DMP Electronics Thinline Aqualite 7000 Series Guía de instalación

DMP Electronics

DMP Electronics 9000 Series Guía de instalación

DMP Electronics

DMP Electronics 9800 Series Guía de instalación

DMP Electronics

DMP Electronics 692F Instrucciones de montaje

DMP Electronics

DMP Electronics Security Command 670 Manual de usuario

DMP Electronics

DMP Electronics Thinline Series Manual de usuario

DMP Electronics

DMP Electronics 7800 Series Guía de instalación

DMP Electronics

DMP Electronics 7760 Manual de usuario

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento