Dish Network EZ Manual de usuario

DISH Network

EZ Remote Control

User Guide

SELECT

POWER

GUIDE

SAT TV

CHANNEL

CONTROL

INFO VOL

CANCEL

123

456

789

RECALL MUTE

All manuals and user guides at all-guides.com

all-guides.com

118866 1

CONTENTS OF THIS GUIDE

About the DISH Network EZ Remote Control................... 3

Buttons and Features Overview........................................ 3

Installing Batteries.............................................................. 4

Receiver Upgrade ............................................................... 5

SettingUp toSwitchtheTVto

Watch Satellite Programming......................................... 5

Connecting Your Satellite Receiver and TV............... 6

Setting Up the Remote to Control Your TV ................ 7

Setting Up on Your Remote Control .................... 8

SettingUp toSwitchtheTVtoa

Preferred Off-Air Channel .............................................. 12

Connecting an Off-Air Antenna to Your

Satellite Receiver.................................................... 12

Setting Up on the Remote Control...................... 13

SettingUp toPassSatellite

Programming Through Your VCR to Your TV.............. 14

Connecting Your Satellite Receiver, VCR,

and TV.................................................................... 15

Setting Up the Remote to Control Your VCR ........... 16

Setting Up on Your Remote Control .................. 17

Using When a VCR is Installed................................... 20

Other Remote Control Instructions.................................. 21

How to Scan for TV Codes....................................... 21

How to Scan for VCR Codes.................................... 22

How to Check the TV Codes .................................... 23

How to Check the VCR Codes................................. 23

How to Remove TV Codes....................................... 24

How to Remove VCR Codes.................................... 24

How to Use the Remote Control....................................... 25

Pointing the Remote Control .................................... 25

Using the Remote Control for

Satellite TV Programming....................................... 25

Using the Remote Control for

Off-Air TV Programming .........................................30

TV and VCR Codes ........................................................... 32

TV Codes.................................................................. 32

VCR Codes............................................................... 39

Limited Warranty ............................................................... 45

All manuals and user guides at all-guides.com

2 118866

Figure 1. The EZ Remote

See How to Use the Remote Control for more details on

each button.

SELECT

POWER

GUIDE

SAT TV

CHANNEL

CONTROL

INFO VOL

CANCEL

123

456

789

RECALL MUTE

Turn on/off the satellite receiver Turn on/off the TV

Channel up

Get information

about satellite

a program

Recall the

last channel

Channel down

Enter channel and

other numbers

Mute the

TV sound

Watch satellite

TV programming

Access the menus

Watch off-air

TV programming

Access the

program guide

Browse without

changing channels

Turn up/down

the TV volume

Access programs

by Themes

Cancel an action

Dish Home

All manuals and user guides at all-guides.com

118866 3

ABOUT THE DISH NETWORK EZ REMOTE

CONTROL

The DISH Network EZ Remote Control makes operating

your DISH Network satellite receiver easy and

convenient. This remote control includes large, easy-to-

find buttons which are most commonly used to control the

basic satellite receiver features you need. In addition, the

DISH Network EZ Remote Control lets you switch

between satellite receiver programming and programming

from an off-air antenna with the press of one button.

BUTTONS AND FEATURES OVERVIEW

Figure 1 on page 2 briefly describes each button on the

DISH Network EZ Remote Control. Most of these buttons

work the same way as the buttons on other DISH Network

remote controls. See the User’s Guide for your DISH

Network satellite receiver for a description of how your

satellite receiver works with these buttons.

There are some added buttons on this remote control to

make operation with your TV easier. These buttons are:

SATELLITE CHANNEL CONTROL - Press to switch

your TV to watch programming from your satellite

receiver.

OFF-AIR CHANNEL CONTROL - Press to switch your

TV to watch programming from your off-air antenna.

TV POWER- Press to turn your TV on or off.

All manuals and user guides at all-guides.com

4 118866

To use these added buttons and other features to control

your TV, follow the step-by-step instructions below to set

up your remote control. This setup also requires you to

connect your satellite receiver to your TV’s tuner using

coaxial cable. After completing your setup, see How to

Use the Remote Control on page 25 for more details on

each button.

INSTALLING BATTERIES

Before you can use the remote control, you must install

four AAA batteries. Use batteries of the same grade, for

example, alkaline or carbon zinc, and do not mix different

grades. Alkaline batteries provide longer battery life.

1. Press down on the arrow on the battery cover and

slide off the cover.

2. Insert the new batteries, making sure that the ends

marked “+” are installed as shown inside the battery

compartment.

3. Replace the battery cover by sliding the cover back

into place.

OPEN

All manuals and user guides at all-guides.com

118866 5

RECEIVER UPGRADE

Turn on your TV the way you normally would to watch

satellite TV programming. Using your DISH Network EZ

Remote Control, press and then try using this remote

control to operate some basic satellite receiver features

like MENU or GUIDE. If the remote control does not work,

your satellite receiver may need to get an upgrade from

the satellite. To receive this upgrade, turn off your

satellite receiver for 20 minutes. After completing the

upgrade, try using the remote control again to make sure it

works.

Note: Check the inside front cover of this guide to see if

the remote control is compatible with your satellite

receiver.

Note: If you are installing the satellite receiver for the first

time, you must use the remote control that came with your

receiver to guide the receiver through the installation

procedures, which includes getting the upgrade from the

satellite.

SETTING UPTOSWITCH THE TV TO

WATCH SATELLITE PROGRAMMING

The following instructions show you how to set up your

system and DISH Network EZ Remote Control so that

when you press the TV gives you satellite

programming every time.

The first thing you will do is make the right connections

between the TV and satellite receiver. After that, you will

set up your remote control to work with your TV and then

set up .

All manuals and user guides at all-guides.com

all-guides.com

6 118866

CONNECTING YOUR SATELLITE RECEIVER AND TV

Figure 2. Connect the Satellite Receiver and TV

1. Connect a coaxial cable between the TV Set Out on

the satellite receiver and the tuner input on the TV

(see Figure 2).

Note: If you connect your TV a different way (for

example, using yellow, red, and white audio/video

RCA-type or S-Video cables), the feature to switch

your TV to satellite programming using will

not work.

2. Set on the back of the receiver to CH3.

Note: If you prefer Channel 4, instructions are

provided later to change this setting.

Note: If your satellite receiver does not have a ,

see your satellite receiver’s User’s Guide for how

to set TV Set Out on the satellite receiver to

Channel 3.

Step 2

Step 1

All manuals and user guides at all-guides.com

118866 7

SETTING UPTHEREMOTE TO CONTROL YOUR TV

1. Find the brand name of your TV in the TV code

tables starting on page 32. You will be referring to

this location for codes in the instructions below.

2. Turn on your TV.

3. Press and hold until both lights turn

on (it takes about five seconds).

4. Release . light will flash.

5. Press . Notice light turns on and stays on.

6. Enter one of the three-digit codes for your TV from

the TV code tables while light is on.

Note: You have about 20 seconds to begin entering

the TV code.

7. Press the MUTE button and watch light.

If light flashes three times, the code is valid

and you can go to step 8. If light does not flash

at all, the code may not have been entered

correctly. So, start over from step 3 and try the code

again.

8. Press and your TV should shut off. If your TV

shuts off, go to step 9. If not, pick another code for

your TV brand from the TV Codes table and go

back to step 3. If you have tried all of the codes and

none work, go to How to Scan for TV and VCR

Codes on page 21.

9. Turn your TV back on by pressing again and

try the other buttons below to make sure they work.

•Press the 0through 9buttons to change channels

on your TV.

SAT TV

TV TV

All manuals and user guides at all-guides.com

8 118866

SETTING UPONYOUR REMOTE CONTROL

•Press and to change channels on

your TV.

•Press to change the TV volume.

If these buttons work, go on to the next section to

set up . If not, pick another code for your TV

brandfromtheTVCodestableandgobackto

step 3.

1. Make sure your TV and satellite receiver are

connected and your remote control is set up to

control your TV using the instructions in the last

two sections.

2. Turn on your TV and tune to a channel other than 3

(for example, 4 or 5).

3. Press and your satellite receiver should turn on

and your TV should tune to Channel 3.

4. Press the MENU button. If you see the satellite

receiver Menu screen,gotostep5.Ifnot,goto

step 15.

5. If you want to keep your satellite programming on

TV Channel 3, check the box below and go to step

28. 3

6. If you prefer to have your satellite programming on

TVChannel4,goontostep7.

VOLVOL

All manuals and user guides at all-guides.com

118866 9

7. Set the switch on the back of the satellite

receiver to CH4. The TV will lose the picture from

the satellite receiver, but this is OK.

Note: If your satellite receiver does not have a

switch, see your satellite receiver’s User’s Guide

for how to set TV Set Out on the satellite receiver to

channel 4.

8. Press and hold until both lights turn

on (it takes about five seconds).

9. Release . light will flash.

10.Enter 0-4.

11.Press MUTE while watching light.

12. light will flash three times.

If the light does not flash at all, repeat this

procedure starting with step 8.

13.Press while watching your TV. If your TV

tunes to Channel 4, go to step 14. If not, go to

step 7.

14.Press the MENU button. If you see the satellite

receiver Menu screen, check the box below and go

to step 28.

15. Answer the questions in Table 1. The information

you provide is what you will use to teach your

remote control to change the channel on your TV

correctly.

SAT TV

SAT

All manuals and user guides at all-guides.com

Otros manuales para EZ

Tabla de contenidos

Otros manuales de Mando a distancia de Dish Network

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network EZ Manual de usuario

Dish Network

Dish Network ViP 211 Series Manual de usuario

Dish Network

Dish Network ViP 922 Slingloded DVR Manual de usuario

Dish Network

Dish Network Solo 301 Instrucciones de uso

Dish Network

Dish Network 20.1 Manual de usuario

Dish Network

Dish Network 11 Hoja de especificaciones

Dish Network

Dish Network 52.0 Manual de usuario

Dish Network

Dish Network DISHPlayer 500 Manual de usuario

Dish Network

Dish Network 54.0 Manual de usuario

Dish Network

Dish Network Platinum Remote Control Manual de usuario

Dish Network

Dish Network 104333 Manual de usuario

Dish Network

Dish Network 135331 Manual de usuario

Dish Network

Dish Network Platinum 121716 Manual de usuario

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network Remote Control Manual de usuario

Dish Network

Dish Network Digital PVR Manual de usuario

Dish Network

Dish Network 129418 Manual de usuario

Dish Network

Dish Network Duo ViP 222 Manual de uso y mantenimiento

Dish Network

Dish Network SoloDVR ViP 612 Manual de uso y mantenimiento

Dish Network

Dish Network Platinum PVR Remote Control Manual de usuario

Dish Network

Dish Network 311k Manual de usuario

Dish Network

Dish Network 54.0 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación