Dish Network 52.0 Manual de usuario

Remote Set Up Guide

Standard_Remote_QSG.indd 1 9/2/2015 4:16:11 PM

To ensure you are in SAT mode, press the SAT button located

on the side of the remote (see page 2) to display programming

and to use the features described in this section.

Note: Some features may not be available depending on your

receiver model.

1. Using the Remote Buttons

Standard_Remote_QSG.indd 2 9/2/2015 4:16:15 PM

Arrow/Select Buttons

•Navigates you

through your

Hopper experience

SAT/TV/AUX

•Mode indicator lights

up when in that

mode

•Channels up/down

•Navigates one full

page in menus

Skip Forward/Forward

•Press to skip

forward 30 seconds

in a program

•Press and hold to

forward through the

program

Skip Back/Back

•Press to skip back

10 seconds in a

program

•Press and hold to

reverse the program

Back/Live TV

•Returns to previous

•Press and hold to

return to viewing

live TV

Pause/Play

•Pauses or plays

a live or recorded

program

Power

•Turns the receiver

on/off

Vol and Mute Buttons

•Controls TV volume

Programming required

Recall

•Returns to previously

viewed channel(s)

Number Buttons

•Enters a channel

number

•Navigates through

menus and program

guide

Home

•Displays Home

Options

•Opens Options

Apps

•Displays Apps menu

DVR

•Displays recorded

programs

Guide

•Displays the Guide

•Searches for

programs

414

615

Info/Help

•Retrieves info on

programs

•Press and hold for

help

Input

•Swaps the tuner

SAT/TV/AUX Mode

•Changes which

device the remote

controls

Standard_Remote_QSG.indd 3 9/2/2015 4:16:15 PM

•Swaps the input in

TV mode

Push the tab toward the top

of the remote to release the

battery door latch and lift

the battery door from the

remote.

Insert 2 AA batteries, putting

thenegativeendsrst.

Match the plus (+) ends with

the plus markings on the

battery case.

Slide the top of the remote

battery cover back into place

and push the bottom of the

cover until it clicks closed.

2. Inserting the Batteries

Standard_Remote_QSG.indd 3 9/2/2015 4:16:16 PM

3. Pairing the Remote to a Hopper

or Joey Receiver

Turn your receiver and TV

on.

Press SYSTEM INFO on the

front panel of the receiver.

Press the SAT button on

your remote. When the

remote is paired, it gives a

series of ascending tones.

Press the BACK/LIVE TV

button to return to live TV.

SYSTEM

INFO

SYS INFO

Joey:

Hopper:

Standard_Remote_QSG.indd 4 9/2/2015 4:16:18 PM

Press the HOME button.

Press the UP Arrow to

access the tabs, then using

the LEFT Arrow highlight

Menu and press SELECT.

Highlight Settings and

press SELECT.

Highlight Diagnostics and

press SELECT.

Press the DOWN Arrow

to highlight Tools under

Receiver.

4. Restoring Your Remote Settings

After your remote is paired, restore your remote settings

to update the remote with settings that were previously

backed-up. Use your remote to complete this step.

Standard_Remote_QSG.indd 5 9/2/2015 4:16:18 PM

Highlight Restore Settings

and press SELECT.

Highlight Restore to

Remote Control and press

SELECT.

Note: Do not move your

remote or receiver during

this process.

Highlight Finished and

press SELECT when the

remote settings have been

restored.

Standard_Remote_QSG.indd 6 9/2/2015 4:16:18 PM

Press the HOME button.

Press the UP Arrow to

access the tabs, then using

the LEFT Arrow highlight

Menu and press SELECT.

Highlight Settings and

press SELECT.

Highlight Remote Control

and press SELECT.

If you would like the VOLUME and MUTE buttons on your

DISH remote to work with your TV or other devices, go to

the Remote Control Settings menu to program your DISH

remote. Use your remote to complete this step.

5. Accessing Your Remote Settings

Standard_Remote_QSG.indd 7 9/2/2015 4:16:18 PM

Highlight Devices,

Customizations, or

Advanced Features and

press SELECT to program

thatspecicsetting.

For additional information,

highlight the ?button and

press SELECT.

Standard_Remote_QSG.indd 8 9/2/2015 4:16:19 PM

6. Backing-up Your Remote and

Receiver Settings

Press the HOME button.

Press the UP Arrow to

access the tabs, then

using the LEFT Arrow

highlight Menu and

press SELECT.

Highlight Settings and

press SELECT.

Highlight Diagnostics

and press SELECT.

Using the DOWN Arrow,

highlight Tools under

Receiver.

After changing your remote settings, it is recommended that

you back-up these settings. These steps back up both the

receiver and remote settings. Use your remote to complete

this step.

Standard_Remote_QSG.indd 9 9/2/2015 4:16:19 PM

Otros manuales para 52.0

Tabla de contenidos

Otros manuales de Mando a distancia de Dish Network

Dish Network

Dish Network 301 IR 123271 Manual de usuario

Dish Network

Dish Network ViP 211 Series Manual de usuario

Dish Network

Dish Network BASIC REMOTE Manual de usuario

Dish Network

Dish Network SoloDVR ViP 612 Manual de uso y mantenimiento

Dish Network

Dish Network 167820 Manual de usuario

Dish Network

Dish Network Platinum Remote Control Manual de usuario

Dish Network

Dish Network 3.1 Manual de usuario

Dish Network

Dish Network Platinum Plus 121150 Manual de usuario

Dish Network

Dish Network 20.1 Manual de usuario

Dish Network

Dish Network 52.0 Manual de usuario

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network Platinum 121716 Manual de usuario

Dish Network

Dish Network EZ Manual de usuario

Dish Network

Dish Network 20.0 Manual de usuario

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network 54.0 Manual de usuario

Dish Network

Dish Network EZ Manual de usuario

Dish Network

Dish Network 6.3 Manual de usuario

Dish Network

Dish Network 40.0 Manual de usuario

Dish Network

Dish Network Duo ViP 222 Manual de usuario

Dish Network

Dish Network 135331 Manual de usuario

Dish Network

Dish Network 52.0 Manual de usuario

Dish Network

Dish Network 129418 Manual de usuario

Dish Network

Dish Network 54.0 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación