Digitus DN-95347 Manual de usuario

PoE+ GIGABIT

ETHERNET SWITCH 2x SFP

Manual

DN-95347 (16 port) • DN-95348 (24 port)

Package Content:

Please open the switch package carefully, confirm the packing box should be as follows:

•

1x Unmanaged Switch

•

1x power cable

•

1x User Manual

•

2x mounting brackets

•

4x mats

•

6x brackets screw

Note:

Rack type models are built in power, no power adapter, and desktop type inorganic

rack mount accessories (mounting brackets / brackets screw).

Introduction

The DIGITUS® PoE+ Gigabit Ethernet Switch 2x SFP provides a simple way to expand a

wired network by transferring power and data over a single Ethernet Cable. It can power

more high-powered devices such as wireless Access Points (APs), IP Cameras or IP Phones.

Moreover, with innovative energy-efficient technology, the Switch can save up to 75% of

the power consumption, making it an eco-friendly solution for your business network.

Parameter

•

The CPU frequency of 500 MHz, 4M cache.

•

Works with IEEE 802.3af/at compliant devices, expanding home and office

networks

•

Innovative energy-efficient technology reduces power consumption by up to 75%

•

Plug and play design, no configuration required

Product Display

Front panel sketch map

DN-95347: 16x 10/100/1000M PoE Port + 2x 1000M SFP, Rackmount, 19-inch steel case

DN-95348: 24*10/100/1000M PoEPort+2*1000M SFP, Rackmount, 19-inch steel case

PWR:

The indicator lights up to indicate that the switch is connected

to the power supply

SYS:

CPU state indicator light after the initialization is completed,

per-second flicker once

Giga/1000M:

The transmission rate of the corresponding port is 1000M

Link:

Data transmission on the corresponding port

VLAN:

DN-95347: Ports 1-14 are isolated from each other.

VLAN ports can only access ports 15-18.

DN-95348: Ports 1-22 are isolated from each other.

VLAN ports can only access ports 23-26.

Back panel sketch map

The 19-inch steel case, back panel sketch map

Power adapter interface:

The power supply of the switch is inserted into the

port, insert additional adapter

Single phase three wire socket:

The power supply of the switch is inserted into the

port, and the input voltage of AC terminal is 100-

240V 50/60Hz

Grounding:

Make the equipment ground

Product mounting

Attention

In order to avoid improper use of equipment damage and personal injury, please note the

following:

During the installation, the power supply remains closed, while wearing anti-static

wrist, and ensure that anti-static wrist and skin good contact, to avoid

potential safety Hidden danger;

The switch can work normally under the correct power supply. Please confirm that

the supply voltage is consistent with the voltage indicated by the switch;

Before the switch is switched on, please confirm that it will not cause overload of

the power circuit, so as not to affect the normal operation of the switch or even

cause unnecessary damage;

In order to avoid the risk of electric shock, switch work should not open the shell.

Even in the case of no electricity, do not open on its own;

Before cleaning the switch, the switch power plug should be pulled out. Please do

not wipe with wet fabric. Please don't use liquid cleaning;

Install the equipment rack generally from the bottom. Avoid overload installation;

The switch surface to avoid placing other heavy objects, so as to avoid accidents

Mounting Switch

Rack Mounting

Check the grounding and stability of the rack.

Secure the supplied rack-mounting brackets to each side of the device with

supplied screws, as illustrated in the following ﬁgure.

After the brackets are attached to the device, use suitable screws (not provided) to

secure the brackets to the rack, as illustrated in the following ﬁgure.

Figure 2-1 Bracket Installation

Figure 2-2 Rack Installation

Desktop mounting

To install the device on the desktop, please follow the steps:

Set the device on a ﬂat surface strong enough to support the entire weight of the

device with all ﬁttings.

Remove the adhesive backing papers from the rubber feet.

Turnover the device and attach the supplied rubber feet to the recessed areas on

the bottom at each corner of the device.

Connect Port

Connect Ethernet port

Connect an Ethernet port of the switch to the device by RJ45 cable.

Connect SFP port

The optical fiber module is grabbed from the side and inserted smoothly along the switch

SFP slot until the optical module is in close contact with the switch.

Note:

To avoid improper operation cause damage to equipment or personal injury, please

pay attention to the following matters

•

Excessive bending of optical fibers is not allowed, and the radius of curvature

should not be less than 10cm.

•

Ensure the cleanliness at the end of the fiber.

•

Please do not look directly at the optical fiber connector; otherwise it may cause

damage to your eyes.

Remarks:

It is recommended to adopt straight line -568B international standard

connection method, as the following ﬁgure shows

Figure 3-3 Network line making

Power supply socket specification

Switch power line single-phase three wire power socket, the middle foot to ground, and

the left foot on the right foot for the zero line and FireWire, please check before the

operation.

Connect the power cord

Check the selection of power supply and the switch marking requirements;

Desktop power input DC output terminal into the switch DC port, then connect the

power line to AC100~240V, 50~60Hz power;

The Rack mount type without power adapter, direct access to AC100~240V,

50~60Hz city electricity

Figure 4-2 Adapter connection

Figure 4-3 Power core connect

Connecting to the Ground

The grounding cable is important to protect the switch from electrical interference. It is

advised to use the grounding cable; if your power is ungrounded which could damage the

switch or its functionality

Figure 4-4 Connecting Grounding Terminal

Note:

The grounding bar and the ground cable are not provided with our product. If

needed, please self purchase them.

Check after installation

Please check the following items after installation:

Check whether there is enough space for heat exchange, air circulation is smooth;

Check the power supply socket power supply switch is in accordance with the

specifications;

Check the power supply, switchboard, rack and other equipment have been

properly grounded;

Grounding Terminal

PoE Switch Hardware Parameters

Type

DN-95347

DN-95348

Port

16x 10/100/1000 M

24x 10/100/1000 M

SFP

2x SFP

POE standards

IEEE802.3af/at, single port PoE power 30 W

POE Port

PoE Budget

380W

Bandwidth

36 Gbps

52 Gbps

Packet forwarding

26.78 Mpps

38.69 Mpps

CPU

500 Mhz

RAM

128 M

MAC

8 K

buffer

4.1 M

FLASH

128 M

Transmission

Store and forward

working temperature

0°C ~ 50°C

Storage temperature

-40°C ~70°C

Operating humidity

10 % ~ 90 % Non-coagulation

Storage humidity

5 % ~ 95 % Non-coagulation

Product size

440 x 290 x 45 mm

Packing size

497 x 313 x 97 mm

Power in

AC 90~265 V 50/60 Hz

Power

400 W

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the

Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid

Germany

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Digitus

Digitus

Digitus DA-70248 Manual de usuario

Digitus

Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Manual de usuario

Digitus

Digitus DN-95331 Manual de usuario

Digitus

Digitus DN-651154 Manual de usuario

Digitus

Digitus DN-95301 Manual de usuario

Digitus

Digitus DN-650102 Manual de usuario

Digitus

Digitus DA-73301 Manual de usuario

Digitus

Digitus DS-12890 Manual de usuario

Digitus

Digitus DS-14210 Manual de usuario

Digitus

Digitus DN-651148 Manual de usuario

Digitus

Digitus DN-95347-1 Manual de usuario

Digitus

Digitus DN-95355 Manual de usuario

Digitus

Digitus DS-45341 Manual de usuario

Digitus

Digitus DA-70886 Manual de usuario

Digitus

Digitus DA-70220 Manual de usuario

Digitus

Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Manual de usuario

Digitus

Digitus DA-70253 Manual de usuario

Digitus

Digitus DS-50304 Manual de usuario

Digitus

Digitus DA-70240 Manual de usuario

Digitus

Digitus DN-650107 Manual de usuario

Digitus

Digitus DN-651126 Manual de usuario

Digitus

Digitus DN-651146 Manual de usuario

Digitus

Digitus DN-80221-3 Manual de usuario

Digitus

Digitus DA-70221 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario