Digitus DS-55502 Manual de usuario

4K HDMI KVM Extender Set, HDBaseT

Manual

DS-55502

The Digitus 4K HDMI KVM Extender Set consists of a transmitter unit

(local control) as well as a receiver unit (remote control). The HDMI

signal can be extended via a network cable (CAT 6) to a maximum

distance of 70 m (Full HD video content). 4K video content can be

extended to up to 40 m using a CAT 6 network cable. The highest

supported video resolution is 4K UHD / 30 Hz. It also makes convenient

access on a computer (mouse and keyboard) possible via the USB ports

on the receiver unit. It is perfectly suited to industrial, commercial and

public applications. The package also includes two bidirectional infrared

units (sender, receiver), which can be used for the remote control of the

connected input source.

Important Safety instructions

Please read below safety instructions carefully before installation and

operation:

Please pay attention to all the warnings and hints on this device.

Do not expose this unit to rain, moisture and liquid.

Do not put any stuff into the device.

Do not repair or open this device without professional people's

guidance.

Make sure good ventilation openings to avoid product overheating

damage.

Shut off power and make sure environment is safe before installation.

Do not plug-in/out the network cables and IR cables when it is in

using to avoid cables damage.

Make sure the specification matched if using 3rd party DC adapters.

Introduction

This product supports to power over CAT cable, connect the power

adapter either with the transmitter unit or with the receiver unit, both

can keep this device working normally. However, it is recommended to

connect power adapter with the receiver end. This KVM Extender is used

to increase the distance between a source (computer, CPU) and its

console (keyboard, mouse, and other peripheral devices). It is useful for

control and security purposes. Therefore it is widely used in command

center, data control center, operation rooms in military, bank,

government, enterprise etc.

Features

1Apply HDBaseT extend technology

2Uncompressed HDMI video signal

3Support distance up to 40m when 4Kx2K@30Hz

4Extend 1080p signal over cat6 up to 70 meters

5Support bi-directional IR pass back

6Support HDCP, CEC, and 24 deep color

7Support mouse and keyboard extension

8Support uncompressed LPCM audio and compressed DTS-HD, Dolby

true HD

9Can be powered by network cable. It only needs to input 12V power

for either transmitter or receiver for normal working

Package Contents

Installation Requirements

1. Source equipment:

HDMI source device (i.e.: computer graphics card, DVD, PS3, or HD

monitoring equipment etc.)

2. Display devices:

With HDMI INPUT port, SDTV, HDTV, projector

3. Network cables:

UTP/STP Cat5e/Cat6/Cat6A/Cat7 network cables, which following the

standard of IEEE-568B

HDMI to HDBaseT TX

sender*1pcs

HDBaseT to HDMI RX

receiver*1pcs

DC12V/2A *1pcs USB Cable x 1pcs

IR blaster extension

cable*1pcs

IR receiver extension

cable*1pcs

User manual*1pcs

Specification

Part No. DS-55502

Technical Transmitter-TX Receiver-RX

HDCP compliance HDCP1.4

Transmission protocol HDBaseT

Transmission distance CAT5E/CAT6/CAT6A/CAT7

Transmission distance

Cat5e

60m Up to 1080p@60Hz 36bpp

35m

1080p@60Hz 48bpp,

1080p@60Hz 3D,

4Kx 2K@30Hz

Cat6

70m Up to 1080p@60Hz 36bpp

40m

1080p@60Hz 48bpp,

1080p@60Hz 3D,

4Kx 2K@30Hz

Video support

480i@60Hz, 480p@60Hz, 576i@50Hz,

576p@50Hz, 720p@50/60Hz,

1080i@50/60Hz, 1080p@50/60Hz

4K×2K@24/25/30Hz

Audio support LPCM, DTS-HD, Dolby True HD

Input TMDS signal 0.7~1.2Vp-p

Input DDC signal 5Vp-p

CEC Supported

RS232 support No

POH support Supported, recommended to connect the

power adapter to the RX unit

latency zero latency

supported

configuration point to point connection

IR passback yes, bi-direction

IR frequency 20-60KHz

HDMI source control bi-direction IR

HDMI connector Type A 19 Pins, Female

Network cable

standard

CAT5E/CAT6/CAT6A/CAT7,

follow IEEE-5688 standard

Mechanical Transmitter-TX Receiver-RX

Housing Metal enclosure

Dimensions

(L×W×H mm) 99.45×94.5×25.7mm

Net weight TX: 220g RX: 230g

Power supply 12V/2A

Power consumption <8W

Operation temperature 0~50

Storage temperature -10~70

Relative humidity 0~95% (no condensation)

Panel Description

1. Transmitter Unit (TX)

①

DC12V input Connect with the power supply

②

Transmission

signal indicator

The first led: It turns on when power on.

The second led:

It turns on when the transmitter unit and the

receiver unit connect well with each other, and it

flashes when there is no transmission between

the transmitter unit and the receiver unit.

The third led:

It turn on when the receiver unit connect well

with the HDMI display device, and it turn off

when no transmission between the receiver

unit and the display device.

③

HDBT Output HDBaseT signal output

④

USB connection

indicator

Indicates that the signal is connected properly

⑤

USB port Connect with computer/PC

⑥

HDMI input Connect with HDMI source device

⑦

IR receiver

extension cable

interface

Connect with IR receiver extension cable.

Please make sure the remote control is within

the required range of IR receiver

⑧

IR blaster

extension cable

interface

Connect with IR blaster extension cable.

Please put the IR blaster close to source

device to get the best IR signal transmission

from receiver.

2. Receiver Unit (RX)

①

DC12V input Connect with the power supply

②

Transmission

signal indicator

1. The first led: It turns on when power on.

2. The second led:

It turns on when the transmitter unit and the

receiver unit connect well with each other, and it

flashes when there is no transmission between

the transmitter unit and the receiver unit.

3. The third led:

It turn on when the receiver unit connect well

with the HDMI display device, and it turn off

when no transmission between the receiver

unit and the display device.

③

HDBT Output HDBaseT signal input

④

USB connection

indicator

Indicates that the signal is connected properly

⑤

USB port Connectwithkeyboardandmouse

⑥

HDMI input Connect with HDMI display device

⑦

IR receiver

extension cable

interface

Connect with IR receiver extension cable.

Please nmake sure the remote control is within

the required range of IR receiver

⑧

IR blaster

extension cable

interface

Connect with IR blaster extension cable. Please

put the IR blaster close to source device to get

the best IR signal transmission from receiver.

Installation Procedures

1. To make a Cat5e/6 network cable

1 white and

orange 4 blue 7 white and

brown

2 orange 5 white and

blue 8 brown

3 white and

green 6 green

2. Connections

[NOTE]: It is recommended to power from the receiver unit.

3. Bi-directional IR pass back

1) It supports bi-directional IR pass back. User can control DVD at TX

end and control TV at RX end.

2) If control at RX end, please connect IR blaster extension cable

with IR OUT of TX and connect IR receiver extension cable with IR

IN of RX. If control at TX end, please connect IR receiver extension

cable with IR IN of TX and connect IR blaster extension cable with

IR OUT of RX.

USB USB HDMI display

keyboard/mouse

Power

Receiver

Sender

HDMI

FAQ

Q: No output on screen?

1) Firstly, please check and make sure the power supply is connected

well. Then, check and make sure all cables are connected correctly.

2) Please check and make sure you have chosen the right HDMI input

port of the TV/screen.

3) Please check and make sure there is HDMI signal to be fed into

transmitter unit, and check whether the receiver unit has been

connected well with the display device.

Q: No “3” led indicator keeps flashing and no output?

A: Check and make sure the HDMI display device has been switched to

the right HDMI input channel.

Q: No “2” led indicator keeps flashing, and no “3” led indicator keeps

off?

A: Check whether the TX’HDMI IN has signal input and make sure

RX’OUT is well connected with HDMI display.

Q: Output image with snow point?

A: Change the HDMI cable between the transmitter unit and the

source device; it will be better to use a shorter HDMI cable for

re-testing.

Disclaimer

The product name and brand name may be registered trademark of related

manufacturers TM and may be omitted on the user manual. The pictures on the user

manual are just for reference, and there may be some slight difference with the real

products. We reserve the rights to make changes without further notice to a product

or system described herein to improve reliability, function or design.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the

shipping content. If the Declaration of Conformity is missing, you can request it by post

under the below mentioned manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid

Germany

Tabla de contenidos

Otros manuales de Extensor de Digitus

Digitus

Digitus DS-55513 Manual de usuario

Digitus

Digitus DS-55100 Manual de usuario

Digitus

Digitus DS-51200 Manual de usuario

Digitus

Digitus DN-82060 Manual de usuario

Digitus

Digitus DS-55302 Manual de usuario

Digitus

Digitus DS-55202 Manual de usuario

Digitus

Digitus DS-55522 Manual de usuario

Digitus

Digitus DS-55400 Manual de usuario

Digitus

Digitus DS-55200 Manual de usuario

Digitus

Digitus DS-55204 Manual de usuario

Digitus

Digitus DS-55517 Manual de usuario

Digitus

Digitus DN-95129 Manual de usuario

Digitus

Digitus DN-95127-1 Manual de usuario

Digitus

Digitus DC-51101-LOCAL Manual de usuario

Digitus

Digitus DS-55508 Manual de usuario

Digitus

Digitus DS-56200 Manual de usuario

Digitus

Digitus DS-55318 Manual de usuario

Digitus

Digitus DS-55306 Manual de usuario

Digitus

Digitus DS-55126 Manual de usuario

Digitus

Digitus DN-95128-1 Manual de usuario

Digitus

Digitus DN-95123 Manual de usuario

Digitus

Digitus DS-55400 Manual de usuario

Digitus

Digitus DS-55506 Manual de usuario

Digitus

Digitus DS-55522 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario