Digital Watchdog V1312XW Manual de usuario

5436 W Crenshaw St. Tampa, FL 33634

Tel: 866-446-3595 / 813-888-9555

Fax: 813-888-9262

www.Digital-Watchdog.com

[email protected]

Technical Support Hours: Monday-Friday

8:30am to 8:00pm Eastern Time

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

ABOUT MANUAL

10112011

Vandal Dome Camera

X12 Zoom V1312XW

User Manual

PRECAUTIONS Table of Contents

Introduction Camera Features 4

Parts and Descriptions 5

Dimensions 6

Installation Inside the box 7

Mounting the Camera 8

Junction Box Installation 9

Wall Mount 10

Pendant Mount 11

Corner Mount 12

Connecting Cables 13

Adjusting the 3 Axis Gimbal 14

Control Board 15

Programming OSD Menu and Glossary 16-17

Troubleshooting 18

Warranty and Service 19-20

Specications 21-22

FCC COMPLIANCE

■ Do not open or modify.

■ Do not open the case except during maintenance and installation,

for it may be dangerous and can cause damages.

■ Do not put objects into the unit.

■

Keep metal objects and ammable substances from entering the camera. It can cause re, short- circuits,

or other damages.

■ Be careful when handling the unit.

■To prevent damages, do not drop the camera or subject it to shock or vibration.

■Do not install near electric or magnetic elds.

■Protect from humidity and dust.

■Protect from high temperature.

■

Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to

high levels.

■Cleaning

■To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

■Mounting Surface

■The material of the mounting surface must be strong enough to support the camera.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful

interference .when the equipment is operated in a residential environment.This equipment generates, uses,

and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction

manual, it may cause harmful interference to radio communications.

WARNING :Changes or modications are not expressly approved by the manufacturer.

PART & DESCRIPTIONS*

FEATURES*

■1/4" Sony Ex-View HAD Double Scan CCD

■560 TV Lines

■3.6~44.3mm Varifocal Auto Iris Lens

■12X Digital Zoom

■Electronic Day and Night with Color Removal Circuit

■WDR (Wide Dynamic Range)

■3D-DNR (3D Digital Noise Reduction)

■Star-Light a.k.a. Sens-Up (Super Low LightTechnology)

■DIS (Digital Image Stabilizer)

■Programmable Privacy Zone (12) & Motion Detection

■AGC / BLC / AWB

■On-Screen Menu Programming with Built-in Joystick

■Secondary Video-BNC Output for Easy Installation

■Auto Sensing 24VAC/12VDC with Line Lock

■RS-485 Built-in



















 Lens

 Video Output Connector - BNC

 Power input Connctor

12VDC/24VAC Dual Voltage

 RS485 : BK(D+), WH(D-)

 Rubber Band

 Black Dome Insert

 Bubble

 Upper case

 Assembly Screws

T20 M4X16

 NPT PLUG

 Bottom Case

 Rubber Pad

 Mounting Screws

INSTALLATION*

Parts Included with DW Camera

1. USER MANUAL

2. MOUNTING TEMPLATE

3. FOUR4 SCREW AND FOUR4 DRY WALL ANCHORS

4. 2ND VIDEO JACK

5. LWRENCH

6. TOOL  0.89MM

7. TOOL  1.5/2.0MM

TOP VIEW

DIMENSIONS IN MILLIMETERS*











 

UNITS :MM

RequiredTools (Not Included)

PHILLIPS HEAD SCREWDRIVER

Instructions to Mount the Camera Junction Box Adapter Installation Instructions

1. Pull wires through and make connections.

Refer to page 13. Use mounting template to

mount camera with dry wall mounts and wood

screws.

1. Check to see all parts are

in the box.

4. Attach the camera to the

junction box using the

machine screws.

2. Use the drywall anchors

and wood screws to

mount the junction box

and rubber gasket to the wall.

5. Attach the camera

housing to the junction

box using the machine

screws.

3. Insert wires through

the wall and make the

appropriate connections.

2. Adjust the camera (pan, tilt, zoom).

See page 14 for details.

3. Use the joystick to adjust the OSD menu.

See page 15, 16, 17 for details.

4. Attach the camera housing to the

junction box using the machine screws.

1110

Junction Box Adapter Installation Instructions Pendant Installation Instructions

1. Check to see all parts are

in the box.

1. Check to see all parts are

in the box.

Use the mounting template to

make pilot holes. Use the dry

wall anchors and wood

screws to attach the assembly

to the wall.

4. Attach the camera to the

pendant mount using the

machine screws.

2. Insert the wires from the

camera through the wall

mount housing.

2. Attach the top shield to

the pendant mount.

5. Attach the camera housing

to the xture.

5. Attach the camera housing

to the xture.

6. Use the mounting template

to make pilot holes. Mount the

camera assembly to the ceiling

using wall mount anchors and

machine screws.

3. Attach the camera to the

wall mount housing.

3. Slide the wires from

the camera through the

pendant mount.

1312

Corner Mount Installation Instructions

1. Check to see all parts are in the box. 2. Attach the two compression ttings to

the corner bracket.

3. Attach the wall mount to the corner

bracket with the 4 machine screws.

4. Attach the assembly to a wall corner with

dry wall anchors and wood screws.

CONNECTING TO MONITORS*

Follow the diagram below to make proper connections to the CRT Monitor or the Monitor.

Power connection - 12VDC/24VAC DualVoltage(Auto polarity detection and protection)

All camera are equipped with a service monitor output on the camera module.

Right

Left

Up Down

12VDC / 24VDC

CCTV Monitor

Monitor

30cm

2nd Video Output

1514

ADJUSTING THE 3-AXIS GIMBAL*CONTROL BOARD*

The Gimbal MechanismYields Maximum Rotation And Placement As Shown Below.

Z-Axis : Rotation 360º

Y-Axis :Tilting 90º/ 82ºIR LED

X-Axis : Panning 360º

 Rotation 360o

 Panning 360o

 Tilting 360o

Joystick

Controller

CON2

CON1

RIGHT

UP DOWN

LEFT

CONTROL BOARD FUNCTIONS

1. Joystick Controller  Functional control of O.S.D.

(On Screen Display)

2. CON1  Second Video Output Connector

3. CON2  RS-485 Connector

1716

MAIN MENU Description

CAMERA SET Camera related functions and data.

INTELLIGENCE Motion detection, and more.

PRIVACY ZONE Privacy related settings

PRESET SET Preset position and Preset ID

OTHER SET Congure for Factory Defaults, and more.

COMMUNICATION Communication set.

SYSTEM INFO Displays the system information.

LANGUAGE Select a language on the OSD menu.

MODULE OSD MENU AND GLOSSARY*

CAMERA SET Description Setting Options

CAMERA ID Make the camera ID and set the place. 54 characters.(2 line) OFF / ON

IRIS ALC/MANUAL Iris select. Setting the BLC and WDR function. ALC(-32~32) / MANUAL(-32~32)

AGC(MOTION) Setting the Max Gain under the low light. OFF / ON(Max.Level Setting)

DNR Digital Noise Reduction : Produces less noise and more color at night. OFF / LOW / MID / HIGH/ USER(1~16)

SHUTTER Set the shutter speed. (High shutter speed) 1/60(1/50) ~ 10Ksec

SENS-UP Super Low Light Technology. Sets the slow shutter speed. FIX X2 ~ OFF ~ AUTO X256

FLICKERLESS Shutter speed OFF / ON

DIS

Digital Image Stabilization : Removes jitters caused by movement or vibrations.

OFF / ON

DAY/NIGHT DayNight Mode , Level set. AUTO / EXT / DAY / NIGHT

WHITE BAL White Balance Mode

ATW1 / ATW2 / AWC / 3200K / 5600K

FOCUS MODE Select the Focus Mode MF / ONEAF / AF

ZOOM SPEED ZOOM Speed set 1~4

DISPLAY ZOOM ZOOM RATIO display OFF / ON

DIGITAL ZOOM Digital Zoom ratio set OFF ~ X12

DETAIL Aperture gain set 0~3

V-SYNC Internal/Linelock mode set INTERNAL / LINE LOCK

AGC COLOR SUP AGC Color Suppression : Color will be reduced at the AGC function. LOW / MID / HIGH

REVERSE Horizontal/Vertical Reverse OFF / H / V / HV

POSI/NEGA Positive or Negative Video output set - / +

PIP Picture In Picture at Digital Zoom operation OFF / ON

INTELLIGENCE Description Setting Options

MOTION Motion detection function OFF / TRACKING / DETECTION

ADVANCED Advanced Motion detection function OFF / FIXED,MOVED

MASK AREA

Set the motion detection exception area

1 ~ 4

DISPLAY Motion Detection display ON/OFF OFF / ON

SENSITIVITY Motion Detection sensitivity 1 ~ 7

RESOLUTION Motion Detection resolution 1 ~ 5

ALARM OUT Alarm out set OFF / ON

PRIVACY ZONE Description Setting Options

PRIVACY SET Set the privacy zone 1 ~12

STYLE Set the privacy style COLOR / MOSAIC 1~4

PRESET Description Setting Options

PRESET SET Set the preset 0 ~ 255

OTHER SET Description Setting Options

LANGUAGE select the language of OSD menu

ENGLISH / FRANCAIS / ESPANOL /JAPANESE / KOREAN /

PROTUGUES

FACTORY DEFAULTS

Set the Factory default setting

OSD COLOR OSD menu color set BW / R / G / B

COMMUNICATION Description Setting Options

PROTOCOL Set protocol of RS-485 device.

PELCO-D/HONEYWELL/SAMSUNG-E,T/VICON/ PANASONIC /

BOSCH/PELCO-P/GE

BAUD RATE Set Baud Rate for RS-485 communication. 2400 / 4800 / 9600 / 19200

ADDRESS Set Camera ID to enable commands from user. 1 ~ 255

SYSTEM INFO Description Setting Options

SYSTEM INFO Camera setting Information

1918

Before sending your camera for repair, check the following or contact our technical specialist.

No VIDEO

Check the coaxial cable and make sure it is connected securely.

Check the lens’iris adjustment at the menu setup of the camera.

Check the power supply and make sure the camera has the proper voltage and current.

Out-of-Focus VIDEO

Check the clear dome cover and the lens for dirt or ngerprints. Use a soft cloth and gently clean.

Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

TROUBSHOOTING

Digital Watchdog (referred to as“the Warrantor”)

warrants the Camera Series against defects in

materials or workmanship as follows.

LABOR :For the initial two (2) years from the date of original purchase,

if the camera is determined to be defective,

the Warrantor will repair or replace the unit, with new or refurbished

product at its option, at no charge.

PARTS :In addition, the Warrantor will supply

replacement parts for the initial two (2) years.

To obtain warranty or out of warranty service,

please contact a Technical Support Representative at

1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM Eastern.

A purchase receipt or other proof of the original purchase date is required

before warranty service is rendered. This warranty only covers failures due to

defects in materials and workmanship which arise during normal use.

This warranty does not cover damage which occurs in shipment or failures

which are caused by products not supplied by the Warrantor or failures

which result from accident, misuse, abuse, neglect, mishandling,

misapplication, alteration, modication, faulty installation, set-up adjustments,

improper antenna, inadequate signal pickup, maladjustment of consumer controls,

improper operation, power line surge, improper voltage supply, lightning damage,

rental use of the product or service by anyone other than an authorized repair

facility or damage that is attributable to acts of God.

WARRANTY INFORMATION*

Tabla de contenidos

Otros manuales de Cámara de seguridad de Digital Watchdog

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-VA553WTIR Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MD724V Manual de usuario

Digital Watchdog

Digital Watchdog BL352IR Manual de usuario

Digital Watchdog

Digital Watchdog B3252DIR Series Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light DWC-B6263TIR Manual de usuario

Digital Watchdog

Digital Watchdog PTZ39XFM Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MV74Wi28 Manual de usuario

Digital Watchdog

Digital Watchdog DWC-MV82WiATW Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix IVA DWC-MB84Wi4T Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MV84WiA Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT Universal HD over Coax... Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT Universal HD over Coax... Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MVT4Wi36 Manual de usuario

Digital Watchdog

Digital Watchdog DWC-V1CMW Manual de usuario

Digital Watchdog

Digital Watchdog Starlight BL5363TIR Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MV421D Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX DWC-MB44Wi650 Manual de usuario

Digital Watchdog

Digital Watchdog DWC-D1363D922 Guía

Digital Watchdog

Digital Watchdog DWC-MB44iALPR Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MF5Wi4TW Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT DWC-B2623WTIRW Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MB75Wi4T Manual de usuario

Digital Watchdog

Digital Watchdog DWC-D4583WTIR Manual de usuario

Digital Watchdog

Digital Watchdog Infinity V3367WTIR Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario