Digital Watchdog MEGApix DWC-MV94WiAT Manual de usuario

Default Login Information

Username: admin Password: admin

Quick Start Guide Quick Start Guide

WHAT’S IN THE BOX

Quick setup

and

Installation

Guides

1 set Tapping Screws

PA 4x25 – 4pcs 1 set

Mounting

Template 1Plastic Plugs

– 4pcs 1 set

Waterproof

Cap 1 set Rubber Plug 1

Hexagonal

Wrench 0.11”

(3mm)

2nd CVBS Local

Monitor Output

and DC12V Input

1 set

DWC-MV94WiAT

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 2 – POWERING THE CAMERA

Power requirements Power consumption

DC12V, PoE

(IEEE 802.3af class 3).

Adapter not Included.

<8W

1. The mounting surface must bear ﬁve times the weight of your camera.

2. Do not let the cables get caught in improper places or the electric line

cover to be damaged. This may cause a breakdown or ﬁre.

3. For the installation process, remove the dome cover from the

camera base using the included wrench.

4. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’ search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

STEP 3 – INSTALLING THE CAMERA

1. Mount the camera to the mounting surface using the included screws

and anchors.

2. To use the camera’s waterproof wiring:

a. Install the LAN cable into .

b. will be assembled

to with a 1/4 turn.

c. Thread tightly to .

3. Adjust the camera’s tilt and angle.

a. Pan and rotation: 0 ~ 345°

b. Tilt: 0 ~ 77°

4. Adjust the camera’s zoom using the T and W buttons

at the base of the camera.

5. Place the dome cover on the camera

using the wrench to tighten the

screws on the dome.

STEP 4 – CABLING

STEP 5 – MANAGING THE SD CARD

Use the diagram below to properly connect power, network, alarm input

and outputs and audio to the camera.

1. To install the camera’s SD Card, locate the SD card slot at the base of

the camera module.

2. Insert a class 10 SD/SDHC/SDXC card into

the SD card slot by pressing the SD card

until clicks.

3. To remove the SD card, press the card

inward until it clicks to release it from the card slot.

Audio Input

Alarm Input/Output

1COM

2 OPEN

3 INA

4 GND

ALA RM

4321

Power

Network

Audio Output

Local Monitor Output

Resetting the camera: To reset the camera, use the tip of a

paper clip or a pencil and press the reset

button at the base of the camera.

Pressing the button for ﬁve (5) seconds

will initiate a camera-wide reset of all

the settings, including network settings.

Zoom+

Zoom-

Pass the wires through and make all the necessary connections. See

STEP 4 for more information.

1. NETWORK CONNECTIONS – Using a PoE Switch or

PoE Injector, connect the camera using an Ethernet

cable for both data and power.

2. NETWORK CONNECTIONS – Not using PoE Switch or

PoE Injector, connect the camera to the switch using an

Ethernet cable for data transmission and use a power

adapter to power the camera.

Rubber Plug

NOTE: This camera’s web client is available via

Internet Explorer®only.

The GUI display may dier by camera models.

Once the camera’s network settings have been setup properly, you can

access the camera’s web viewer.

To open the camera using the DW IP Finder:

1. Find the camera using the DW IP Finder.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will open

up in your default web browser.

4. Enter the camera’s username and password.

To open the camera using the web browser:

1. Open a web browser (Internet Explorer® 8.0 or above).

2. Enter the camera’s IP address and port in the address bar.

Example: http://<ipaddress>:<port>.

Port forwarding may be necessary to access the camera from a

dierent network. Contact your network administrator for more

information.

3. Enter the camera’s username and password (default admin/admin).

If you are accessing the camera for the ﬁrst time, install the ActiveX

player for web ﬁles to view video from the camera.

Quick Start Guide

STEP 6 – DW® IP FINDER™

Thumbnail view

Firmware version

Camera’s uptime

Open Device

conﬁguration

settings

Filter device type to scan

Scan devices

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Device’s

information

Use the DW®IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Network Setup

1. To install the DW IP Finder, go to

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page.

3. Go to the “Software” tab on the DW IP Finder page to download

the installation ﬁle.

4. Follow the installation to install the DW IP Finder. Open the DW IP

Finder and click ‘Scan Devices’. It will scan the selected network

for all supported devices and list the results in the table. During the

scan, the DW® logo will turn gray.

5. When connecting to the camera for the ﬁrst time, a password must

be set. To set up a password for your new camera:

Select DHCP to allow the camera to receive its IP address automatically

from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

Spectrum® IPVMS.

Contact your network administrator for more information.

Default TCP/IP information: DHCP ‘Port forwarding’ has to be set in your network’s

router for external access to the camera.

a. Check the box next to your new camera from

the IP Finder’s search results. You can select

multiple cameras.

b. Click “Bulk Password Assign” on the left.

c. In the pop-up window, enter admin/ admin in the

current username and password ﬁelds. Enter a

new username and password to the right.

d. Press “change” to apply all changes.

6. Select a camera from the list by double-clicking on

the camera’s image or clicking on the ‘Click’ button

under the IP Conf. column. The pop-up window

will show the camera’s current network settings,

allowing admin users to adjust the settings as

needed.

7. To access the camera’s web page, go to the

IP Conﬁg page and click on the ‘View Camera

Website’.

8. To save the changes made to the camera’s setting,

input the username and password of the camera

and click Apply.

Rev Date: 01/22

Speciﬁcations and pricing are subject to change without notice.

NOTE: Some menu options may not be available based on the

camera model. See the full manual for more information.

STEP 7 – WEB VIEWER

Otros manuales de Cámara de seguridad de Digital Watchdog

Digital Watchdog

Digital Watchdog DWC-LPR550 Manual de usuario

Digital Watchdog

Digital Watchdog PowerPix DWC-B6361WTIR Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX PANO DWC-PVF5M1TIR Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MV85WiAT Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix Ai DWC-PDS10Wi28A Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix DWC-MVC8WiATW Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light DWC-V7253WTIR Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT AHD DWC-V7753WTIR Manual de usuario

Digital Watchdog

Digital Watchdog B2373D Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix Ai DWC-XSBA08Mi Manual de usuario

Digital Watchdog

Digital Watchdog B3252DIR Series Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT DWC-B2623WTIRW Manual de usuario

Digital Watchdog

Digital Watchdog MegaPix Pano DWC-PZ21M69T Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT DWC-D4283WTIR Manual de usuario

Digital Watchdog

Digital Watchdog Star-Light Plus DWC-VA583WTIR Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX DWC-MB44Wi650 Manual de usuario

Digital Watchdog

Digital Watchdog MEGAPIX DWC-MV94Wi36T Manual de usuario

Digital Watchdog

Digital Watchdog DWC-V3363D Manual de usuario

Digital Watchdog

Digital Watchdog x12 WDR PTZ Manual de usuario

Digital Watchdog

Digital Watchdog MD421TIR/B Manual de usuario

Digital Watchdog

Digital Watchdog Starlight V1363TIR Manual de usuario

Digital Watchdog

Digital Watchdog STAR-LIGHT 960H DWC-V6553D Manual de usuario

Digital Watchdog

Digital Watchdog MegaPix Pano DWC-PVF5M1TIRC6 Manual de usuario

Digital Watchdog

Digital Watchdog MEGApix IVA DWC-MB84Wi4T Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario