Digital Equipment PRIORIS ZX MP5 Manual de usuario
Troubleshooting
Guide
PRIORIS ZX MP5 SERVICE INFORMATION
1-1
1
Initial Troubleshooting
Initial Troubleshooting
• Record all configuration information and have readily available.
• Turn off server, wait until all hard disk drives completely spin down, and
then turn back on.
• Record all error messages.
• Make sure all cables and connections are secure.
• Make sure all necessary video, printer, and application device drivers
are properly installed.
• Troubleshoot one problem at a time.
• Try to duplicate the problem.
• Run the diagnostic software.
• Run the SCU.
2-1
2
Troubleshooting
Server Troubleshooting
Problem Possible Cause Action
No response when the
server is turned on. Server is not plugged
in.
No power at the wall
outlet.
Main logic board failed.
Main logic board
jumpers incorrectly set.
CPU module has failed.
No memory module or
SIMMs installed.
Side panels removed.
Power supply failed.
Turn off the server, plug it in,
and then turn it back on again.
Use another wall outlet.
Replace main logic board.
Set all appropriate jumpers.
Reseat the CPU module. If
failure continues, replace CPU
module.
Install SIMMs and memory
module.
Install side panels.
Replace power supply.
continued
Troubleshooting
2-2
Problem Possible Cause Action
Power is on, but there is
no screen display. Monitor brightness and
contrast controls are
not correctly set.
Monitor is off.
Monitor cable is
incorrectly installed.
Incorrect video drivers
installed.
Video controller has
failed.
Monitor has failed.
Adjust the brightness and
contrast controls.
Turn on the monitor.
Check all monitor connections.
Install the correct video
drivers.
Replace main logic board.
Replace monitor.
Power is on but no
OCP display. OCP button not turned
on or OCP backlight is
disabled in SCU.
OCP has failed.
Press any keyboard key or
OCP button at the front of the
server.
Make sure OCP backlight is
set to ON in the SCU.
Replace OCP display.
Power is on but cooling
fans do not work. Fans disconnected
from main logic board.
One or more fans
failed.
Connect the fans.
Replace fan(s).
Server operates
incorrectly after
installing a CPU
module.
CPU module installed
incorrectly.
Primary CPU module
has failed.
Secondary CPU
module has failed.
Reinstall CPU module.
Replace CPU module.
Remove CPU module and
reboot. If server boots without
errors, replace CPU module.
continued
Troubleshooting
2-3
Problem Possible Cause Action
Server operates
incorrectly after
installing optional
expansion board.
Expansion board
installed incorrectly.
Did not run SCU to
configure expansion
board after installation.
Did not install CFG file
for expansion board.
Expansion board has
failed.
Remove expansion board and
reinstall.
Run the SCU to properly
configure expansion board.
Run SCU and add CFG file (if
necessary).
Remove expansion board and
reboot. If server boots without
errors, replace expansion
board.
Server operates
incorrectly after
installing optional
memory (SIMMs).
SIMMs installed
incorrectly.
SIMMs have failed.
Memory module
installed incorrectly.
Memory module failed.
Remove SIMMs and reinstall.
Reorder SIMMs. Make sure
SIMMs are installed in the
appropriate memory banks
and are completely filled. If
problem persists, replace
SIMMs.
Reinstall memory module.
Replace memory module.
No response to
keyboard commands. Keyboard might be
password protected by
a local or remote
control program.
Keyboard is not
connected.
Keyboard is connected
to the mouse port.
Keyboard failed.
Enter the keyboard password.
Power down the server and
connect the keyboard.
Power down the server and
connect the keyboard to the
keyboard port.
Replace keyboard.
continued
Troubleshooting
2-4
Problem Possible Cause Action
No response to mouse
commands. Mouse might be
password protected by
a local or remote
control program.
Mouse is not
connected.
Mouse is connected to
the keyboard port.
Mouse driver not
installed.
Mouse trackball dirty.
Mouse failed.
Enter the keyboard and
mouse password.
Power down the server and
connect the mouse.
Power down the server and
connect the mouse to the
mouse port.
Install the appropriate mouse
driver.
Clean trackball.
Replace mouse.
Server operates
correctly but application
software does not.
Application software
installed incorrectly.
CPU speed setting
causes conflict with
application software.
Having system cache
enabled causes conflict
with application
software.
SCSI device has failed.
Refer to your application
software documentation.
Run the SCU and reduce CPU
speed setting.
Run the SCU and disable
system cache.
Replace SCSI device.
continued
Troubleshooting
2-5
Problem Possible Cause Action
Server does not boot
from CD-ROM drive. CD-ROM drive is not
connected to the
Adaptec controller.
Connect the CD-ROM drive to
the onboard 7870 Adaptec
controller.
CD-ROM drive not
configured as a
bootable device.
Change the CD-ROM setting
to “bootable” using
SCSI
Select
.
CD-ROM disk is not
bootable. CD-ROM disk media must be
bootable to boot from CD-
ROM disk.
SCSI device has failed. Make sure CD-ROM disk is
bootable. If failure continues,
replace SCSI device.
Target diskette drive
cannot read or write
information.
Diskette is not
formatted.
Diskette is worn or
damaged.
Diskette is write-
protected.
Diskette drive is empty.
Diskette write
protection enabled.
Diskette drive has
failed.
Format the diskette.
Try another diskette.
Slide the write-protect switch
so the hole is not visible.
Insert a diskette.
Run the SCU and set the
Diskette Write Protection
option to “Disabled.”
Secure ribbon cable and other
connectors on back of diskette
drive. If failure continues,
replace diskette drive.
Troubleshooting
2-6
Disk Drive Troubleshooting
Problem Possible Cause Action
Server does not
recognize an
internal SCSI
device.
SCSI device jumpers
incorrectly set.
SCSI ID conflicts.
Terminating resistors not
removed from the SCSI
device.
SCSI controller has failed.
Loose SCSI cable.
SCSI cable incorrectly
installed between SCSI
controller, SCSI device or
backplane.
Refer to the supplied kit
installation instructions.
Refer to the supplied kit
installation instructions.
Remove terminating resistors.
Refer to the supplied kit
installation instructions.
Replace main logic board.
Secure all cable connections.
Correctly install SCSI cable.
Server does not
recognize an
external SCSI
device.
SCSI device jumpers
incorrectly set.
SCSI ID conflicts.
Terminating resistors not
removed from the SCSI
device.
SCSI controller has failed.
Loose SCSI cable.
SCSI cable incorrectly
installed between SCSI
controller and rear panel
connector or external
SCSI device and rear
panel connector.
Refer to the supplied kit
installation instructions.
Refer to the supplied kit
installation instructions.
Remove terminating resistors.
Refer to the supplied kit
installation instructions.
Replace main logic board.
Secure all cable connections.
Correctly install SCSI cable.
continued
Troubleshooting
2-7
Problem Possible Cause Action
Server does not
boot from an internal
SCSI hard disk
drive.
SCSI boot hard disk
drive not formatted.
SCSI device drivers not
installed or incorrectly
installed on SCSI boot
hard disk drive.
Operating system
software is not installed
on the SCSI boot hard
disk drive.
Requested partition does
not exist.
SCSI boot hard disk
drive at wrong SCSI
address.
Format the SCSI hard disk
drive.
CAUTION: Formatting the
SCSI hard disk drive will destroy
all the data on the drive.
Properly install all required SCSI
device drivers.
Install the appropriate operating
system.
Partition the SCSI hard disk
drive and then reload the
operating software.
Set SCSI boot hard disk drive to
lowest “primary” SCSI address.
continued
Troubleshooting
2-8
Problem Possible Cause Action
Server does not
boot from a target
diskette drive.
Drive ID incorrectly set.
Diskette drive not
enabled.
Diskette boot option
disabled.
Diskette does not contain
start-up files.
Diskette drive is empty.
Diskette is worn or
damaged.
Loose cables.
Make sure the drive ID is
correctly set. Refer to the
documentation that was
supplied with the diskette drive.
Run the BIOS Setup utility to
enable the diskette drive.
Run the SCU and set boot
option A then C.
Insert a diskette with the correct
start-up files.
Insert a diskette that contains
an operating system.
Try another diskette.
Secure all cable connections.
continued
Tabla de contenidos
Otros manuales de Servidor de Digital Equipment
Digital Equipment
Digital Equipment PRIORIS HX Manual de usuario
Digital Equipment
Digital Equipment Digital AlphaServer 400 Series Manual de operación
Digital Equipment
Digital Equipment AlphaServer 8400 Manual de usuario
Digital Equipment
Digital Equipment DIGITAL Server 7100 1200 Manual de usuario
Digital Equipment
Digital Equipment DECserver 90TL Manual de usuario
Digital Equipment
Digital Equipment DEC 3000 Instrucciones de funcionamiento e instalación
Digital Equipment
Digital Equipment 5220 Series Manual de usuario
Digital Equipment
Digital Equipment AlphaServer 1000 Manual de usuario
Digital Equipment
Digital Equipment DECserver 300 Hoja de instrucciones
Digital Equipment
Digital Equipment PRIORIS ZX 5000 MP Manual de usuario
Digital Equipment
Digital Equipment AlphaServer 1000A Manual de usuario
Digital Equipment
Digital Equipment Digital AlphaServer 400 Series Manual de operación
Digital Equipment
Digital Equipment Prioris HX 6000 Manual de usuario
Digital Equipment
Digital Equipment AlphaServer 2000 Manual de usuario
Digital Equipment
Digital Equipment Prioris HX MP Manual de usuario
Digital Equipment
Digital Equipment 7100R Series Manual de usuario
Digital Equipment
Digital Equipment DECserver 700-08 Manual de usuario
Digital Equipment
Digital Equipment 3220 Series Guía del usuario
Digital Equipment
Digital Equipment AlphaServer 1000 Guía de inicio rápido
Digital Equipment
Digital Equipment DECserver 300 Manual de referencia
