Digital Equipment AlphaServer 1000 Manual de usuario

AlphaServer1000

ServiceGuide

Order Number: EK–DTLSV–SV. B01

Digital Equipment Corporation

Maynard, Massachusetts

First Printing, February 1995

Second Printing, July 1995

Digital Equipment Corporation makes no representations that the use of its products in the

manner described in this publication will not infringe on existing or future patent rights, nor do

the descriptions contained in this publication imply the granting of licenses to make, use, or sell

equipment or software in accordance with the description.

Possession, use, or copying of the software described in this publication is authorized only pursuant

to a valid written license from Digital or an authorized sublicensor.

The following are trademarks of Digital Equipment Corporation: AXP, DEC, DECchip, DEC VET,

Digital, OpenVMS, StorageWorks, VAX DOCUMENT, the AXP logo, and the DIGITAL logo.

Digital UNIX is a registered trademark in the United States and other countries licensed

exclusively through X/Open Company Ltd. Windows NT is a trademark of Microsoft Corp.

All other trademarks and registered trademarks are the property of their respective holders.

FCC NOTICE: The equipment described in this manual generates, uses, and may emit radio

frequency energy. The equipment has been type tested and found to comply with the limits for

a Class B computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed

to provide reasonable protection against such radio frequency interference when operated in a

commercial environment. Operation of this equipment in a residential area may cause interference,

in which case the user at his own expense may be required to take measures to correct the

interference.

S2920

This document was prepared using VAX DOCUMENT Version 2.1.

Contents

Preface ................................................ xi

1 Troubleshooting Strategy

1.1 Troubleshooting the System . ....................... 1–1

1.1.1 Problem Categories ........................... 1–2

1.2 Service Tools and Utilities . . ....................... 1–7

1.3 Information Services ............................. 1–9

2 Power-Up Diagnostics and Display

2.1 Interpreting Error Beep Codes ...................... 2–2

2.1.1 SROM Memory Power-Up Tests . . . ............... 2–3

2.2 Power-Up Screen . ............................... 2–7

2.2.1 Console Event Log ............................ 2–8

2.3 Mass Storage Problems Indicated at Power-Up . . . ...... 2–9

2.4 Storage Device LEDs ............................. 2–11

2.5 EISA Bus Problems Indicated at Power-Up ............ 2–14

2.5.1 Additional EISA Troubleshooting Tips ............. 2–15

2.6 PCI Bus Problems Indicated at Power-Up ............. 2–16

2.7 Fail-Safe Loader. . ............................... 2–17

2.7.1 Fail-Safe Loader Functions ..................... 2–17

2.7.2 Activating the Fail-Safe Loader . . . ............... 2–17

2.8 Power-Up Sequence .............................. 2–19

2.8.1 AC Power-Up Sequence . ....................... 2–19

2.8.2 DC Power-Up Sequence . ....................... 2–20

2.9 Firmware Power-Up Diagnostics .................... 2–20

2.9.1 Serial ROM Diagnostics . ....................... 2–20

2.9.2 Console Firmware-Based Diagnostics.............. 2–21

iii

3 Running System Diagnostics

3.1 Running ROM-Based Diagnostics ................... 3–1

3.2 Command Summary ............................. 3–2

3.3 Command Reference ............................. 3–3

3.3.1 test . ....................................... 3–4

3.3.2 cat el and more el ............................ 3–7

3.3.3 memory .................................... 3–8

3.3.4 netew ...................................... 3–10

3.3.5 network .................................... 3–12

3.3.6 net-s ...................................... 3–14

3.3.7 net-ic...................................... 3–15

3.3.8 kill and kill_diags ............................ 3–16

3.3.9 show_status . . ............................... 3–17

3.4 Acceptance Testing and Initialization. . ............... 3–18

3.5 DECVET...................................... 3–18

4 Error Log Analysis

4.1 Fault Detection and Reporting ...................... 4–1

4.1.1 Machine Check/Interrupts ...................... 4–2

4.2 Error Logging and Event Log Entry Format ........... 4–4

4.3 Event Record Translation. . . ....................... 4–5

4.3.1 OpenVMS Translation Using DECevent ........... 4–5

4.3.2 Digital UNIX Translation Using DECevent . . . ...... 4–6

5 System Conﬁguration and Setup

5.1 Verifying System Conﬁguration ..................... 5–2

5.1.1 System Firmware ............................. 5–2

5.1.2 Switching Between Interfaces ................... 5–4

5.1.3 Verifying Conﬁguration: ARC Menu Options for

Windows NT . ............................... 5–4

5.1.3.1 Display Hardware Conﬁguration .............. 5–5

5.1.3.2 Set Default Variables ....................... 5–7

5.1.4 Verifying Conﬁguration: SRM Console Commands for

DEC OSF/1 and OpenVMS ..................... 5–9

5.1.4.1 show conﬁg............................... 5–9

5.1.4.2 show device .............................. 5–11

5.1.4.3 show memory ............................. 5–12

5.1.4.4 Setting and Showing Environment Variables ..... 5–12

5.2 System Bus Options .............................. 5–17

5.2.1 CPU Daughter Board . . . ....................... 5–19

5.2.2 Memory Modules ............................. 5–19

5.3 Motherboard ................................... 5–20

5.4 EISA Bus Options ............................... 5–21

5.5 ISA Bus Options . ............................... 5–21

5.5.1 Identifying ISA and EISA options . ............... 5–22

5.6 EISA Conﬁguration Utility . ....................... 5–22

5.6.1 Before You Run the ECU ....................... 5–23

5.6.2 How to Start the ECU . . ....................... 5–24

5.6.3 Conﬁguring EISA Options ...................... 5–25

5.6.4 Conﬁguring ISA Options ....................... 5–26

5.7 PCI Bus Options . ............................... 5–28

5.8 SCSI Buses .................................... 5–28

5.8.1 Single Controller (On-Board) Conﬁgurations . . ...... 5–29

5.8.2 Multiple Controller Conﬁgurations ............... 5–32

5.9 Power Supply Conﬁgurations ....................... 5–34

5.10 Console Port Conﬁgurations . ....................... 5–37

6 AlphaServer 1000 FRU Removal and Replacement

6.1 AlphaServer 1000 FRUs........................... 6–1

6.2 Removal and Replacement . . ....................... 6–6

6.2.1 Cables ..................................... 6–8

6.2.2 CPU Daughter Board . . . ....................... 6–22

6.2.3 Fans ....................................... 6–23

6.2.4 StorageWorks Drive ........................... 6–25

6.2.5 Internal StorageWorks Backplane . ............... 6–26

6.2.6 Memory Modules ............................. 6–28

6.2.7 Interlock Switch .............................. 6–32

6.2.8 Motherboard . ............................... 6–33

6.2.9 NVRAM Chip (E14) and NVRAM TOY Clock Chip

(E78) ...................................... 6–37

6.2.10 OCP Module . . ............................... 6–37

6.2.11 Power Supply . ............................... 6–40

6.2.12 Speaker .................................... 6–41

6.2.13 Removable Media ............................. 6–42

A Default Jumper Settings

A.1 Motherboard Jumpers ............................ A–2

A.2 CPU Daughter Board (J3 and J4) Supported Settings .... A–4

A.3 CPU Daughter Board (J1 Jumper) ................... A–6

Glossary

Index

Examples

5–1 Sample Hardware Conﬁguration Display ........... 5–6

Figures

2–1 Jumper J1 on the CPU Daughter Board ........... 2–6

2–2 AlphaServer 1000 Memory Layout . ............... 2–7

2–3 StorageWorks Disk Drive LEDs (SCSI) ............ 2–12

2–4 Floppy Drive Activity LED...................... 2–12

2–5 CD–ROM Drive Activity LED ................... 2–13

2–6 Jumper J1 on the CPU Daughter Board ........... 2–18

5–1 System Architecture: AlphaServer 1000 ........... 5–2

5–2 Device Name Convention ....................... 5–11

5–3 Card Cages and Bus Locations................... 5–18

5–4 Memory Layout on the Motherboard .............. 5–20

5–5 ISA and ISA Boards ........................... 5–22

5–6 PCI Board . . . ............................... 5–28

5–7 Single Controller Conﬁguration with Dual Bus

StorageWorks Shelf ........................... 5–30

5–8 Single Controller Conﬁguration with Single Bus

StorageWorks Shelf ........................... 5–31

5–9 Dual Controller Conﬁguration with Single Bus

StorageWorks Shelf ........................... 5–32

5–10 Dual Controller Conﬁguration with Dual Bus

StorageWorks Shelf ........................... 5–33

5–11 Power Supply Conﬁgurations .................... 5–35

5–12 Power Supply Cable Connections . . ............... 5–36

6–1 FRUs, Front Right ............................ 6–4

6–2 FRUs, Rear Left .............................. 6–5

6–3 Opening Front Door ........................... 6–6

6–4 Removing Top Cover and Side Panels ............. 6–7

6–5 Floppy Drive Cable (34-Pin) ..................... 6–8

6–6 OCP Module Cable (10-Pin) ..................... 6–9

6–7 Power Cord . . ............................... 6–10

6–8 Power Supply Current Sharing Cable (3-Pin) . ...... 6–11

6–9 Power Supply DC Cable Assembly . ............... 6–12

6–10 Power Supply Storage Harness (12-Pin)............ 6–13

6–11 Interlock/Server Management Cable (2-pin) . . . ...... 6–14

6–12 Internal StorageWorks Jumper Cable (50-Pin). ...... 6–15

6–13 SCSI (J15 StorageWorks Shelf to Bulkhead Connector

or Bulkhead to Multinode) Cable (50-Pin) .......... 6–16

6–14 SCSI (J15 StorageWorks Shelf to Bulkhead Connector

or Bulkhead to Multinode) Cable (50-Pin) .......... 6–17

6–15 SCSI (J1 or J14 StorageWorks Shelf to Bulkhead

Connector) Cable (50-Pin) ...................... 6–18

6–16 SCSI (Embedded 8-bit) Multinode Cable (50-Pin) .... 6–19

6–17 SCSI RAID Internal Cable (50-Pin)

(Single-Channel) ............................. 6–20

6–18 SCSI RAID Internal Cable (50-Pin) (Dual-Channel) . . 6–21

6–19 Removing CPU Daughter Board . . ............... 6–22

6–20 Removing Fans .............................. 6–24

6–21 Removing StorageWorks Drive ................... 6–25

6–22 Removing Power Supply ....................... 6–26

6–23 Removing Internal StorageWorks Backplane . . ...... 6–27

6–24 Memory Layout on Motherboard . . ............... 6–28

6–25 Removing SIMMs from Motherboard .............. 6–29

6–26 Installing SIMMs on Motherboard . ............... 6–30

6–27 Removing the Interlock Safety Switch ............. 6–32

6–28 Removing EISA and PCI Options. . ............... 6–33

6–29 Removing CPU Daughter Board . . ............... 6–34

6–30 Removing Motherboard . ....................... 6–35

6–31 Motherboard Layout . . . ....................... 6–36

6–32 Removing Front Door . . . ....................... 6–37

6–33 Removing Front Panel . . ....................... 6–38

vii

6–34 Removing the OCP Module ..................... 6–39

6–35 Removing Power Supply ....................... 6–40

6–36 Removing Speaker ............................ 6–41

6–37 Removing a CD–ROM Drive .................... 6–42

6–38 Removing a Tape Drive . ....................... 6–43

6–39 Removing a Floppy Drive ....................... 6–44

A–1 Motherboard Jumpers (Default Settings)........... A–2

A–2 AlphaServer 1000 4/200 CPU Daughter Board

(Jumpers J3 and J4) . . . ....................... A–4

A–3 AlphaServer 1000 4/233 CPU Daughter Board

(Jumpers J3 and J4) . . . ....................... A–5

A–4 CPU Daughter Board (J1 Jumper) . ............... A–6

Tables

1–1 Diagnostic Flow for Power Problems .............. 1–3

1–2 Diagnostic Flow for Problems Getting to Console

Mode ...................................... 1–4

1–3 Diagnostic Flow for Problems Reported by the Console

Program .................................... 1–5

1–4 Diagnostic Flow for Boot Problems ............... 1–6

1–5 Diagnostic Flow for Errors Reported by the Operating

System ..................................... 1–7

2–1 Interpreting Error Beep Codes ................... 2–2

2–2 SROM Memory Tests, CPU Jumper J1 ............ 2–4

2–3 Mass Storage Problems . ....................... 2–9

2–4 Troubleshooting Problems with SWXCR-xx RAID

Controller ................................... 2–11

2–5 EISA Troubleshooting . . ....................... 2–14

2–6 PCI Troubleshooting........................... 2–16

3–1 Summary of Diagnostic and Related Commands ..... 3–2

4–1 AlphaServer 1000 Fault Detection and Correction .... 4–2

5–1 Listing the ARC Firmware Device Names .......... 5–5

5–2 ARC Firmware Device Names ................... 5–5

5–3 ARC Firmware Environment Variables ............ 5–8

5–4 Environment Variables Set During System

Conﬁguration . ............................... 5–13

5–5 Operating System Memory Requirements .......... 5–20

viii

5–6 Summary of Procedure for Conﬁguring EISA Bus

(EISA Options Only) . . . ....................... 5–26

5–7 Summary of Procedure for Conﬁguring EISA Bus with

ISA Options . ............................... 5–27

6–1 AlphaServer 1000 FRUs. ....................... 6–2

6–2 Power Cord Order Numbers ..................... 6–10

Otros manuales para AlphaServer 1000

Tabla de contenidos

Otros manuales de Servidor de Digital Equipment

Digital Equipment

Digital Equipment DECserver 300 Manual de referencia

Digital Equipment

Digital Equipment 5300 Manual de lista de piezas

Digital Equipment

Digital Equipment MUXserver 100 Manual de usuario

Digital Equipment

Digital Equipment PRIORIS ZX 5000 MP Manual de usuario

Digital Equipment

Digital Equipment AlphaServer 2000 Manual de usuario

Digital Equipment

Digital Equipment AlphaServer 1000 Guía de inicio rápido

Digital Equipment

Digital Equipment Prioris HX MP Manual de usuario

Digital Equipment

Digital Equipment Prioris XL 5166 Manual de usuario

Digital Equipment

Digital Equipment DECserver 700-08 Manual de usuario

Digital Equipment

Digital Equipment MicroVAX II 630QB Manual de usuario

Digital Equipment

Digital Equipment DECserver 900TM Manual de usuario

Digital Equipment

Digital Equipment 5200 Series Manual de usuario

Digital Equipment

Digital Equipment MicroVAX 3600 Manual de instrucciones

Digital Equipment

Digital Equipment Prioris HX 6000 Manual de usuario

Digital Equipment

Digital Equipment 7100R Series Manual de usuario

Digital Equipment

Digital Equipment MicroVAX II 630QB Manual de usuario

Digital Equipment

Digital Equipment 5100 Series Manual de usuario

Digital Equipment

Digital Equipment DECserver 900MC Instrucciones de funcionamiento y mantenimiento

Digital Equipment

Digital Equipment 3300R Manual de usuario

Digital Equipment

Digital Equipment DEC 3000 Instrucciones de funcionamiento e instalación

Digital Equipment

Digital Equipment Prioris HX MP Manual de usuario

Digital Equipment

Digital Equipment Server 3100 series Manual de usuario

Digital Equipment

Digital Equipment 3220 Series Manual de usuario

Digital Equipment

Digital Equipment 5300 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario