Digisol DG-GS1010PF-B Manual de usuario
DG-GS1010PF-B
8 Port 10/100/1000Mbps Gigabit
Switch with 2 Port 10/100/
1000Mbps Uplink Ports
Quick Installation Guide
2000Mbps
UPTO
8
V1.1
2024-01-04
Copyright 2024 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
Copyright
Trademarks:
®
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.
The following items should be present in your package:
Package Contents :
• Switch (1 No)
• Power Cord (1 No)
• Quick Installation Guide
Make sure that the package contains above items.
This document will guide you on the correct use of products, to prevent any
loss or damage to the device to avoid void of warranty. Please read the
instructions carefully before using the equipment and strictly observe while
using it.
This unmanaged PoE switch series support 4 or 8 nos. of PoE ports with
2 uplink ports in surveillance / VLAN mode. The switches support PoE on all
the downlink ports. The PoE switch provides power and data transmission via
Cat cables. PoE ports supply power at the standard of IEEE802.3af/at. Auto-
sensing function can supply power to PD device (IEEE802.3af/at standard).
If the PoE device disconnected, it would stop supplying power. The PoE
switch features simple and reliable design and automatic identification of
PoE supply voltage and power, speed, full-duplex and Auto Uplink cable type.
This cost-effective switch can apply to wireless access point (AP) and IP-
based surveillance.
Product Overview :
• Do not install the equipment in direct sunlight or near any equipment
that generates high amount of heat
• Do not install the equipment in damp, dusty or sooty places
• Always keep the equipment installed horizontally, or on a stable platform
to prevent the product from falling
• Do not drop or spill liquids on the equipment and ensure that liquid-filled
items are not spilled on the equipment
• Prevent any sort of liquid from flowing into equipment
• Install the switch in a well-ventilated place. Do not block the ventilation
vent of the equipment
• Equipment can only be used within the permissible input & output range
• Do not disassemble the equipment by your own self
• Maintain the range of humidity while storing or during transportation
Precautions :
The product must use the wired components (power cable) recommended by
the region and be used within its permissible specifications. Use the power
supply that meets the requirements of SELV (Safe Ultra-Low Voltage) and
conform to IEC 60950-1. The rated voltage of Limited Power Source
(restricted power supply) is used for power supply. The label of the switch
should be prevailed till the product warranty.
If power plug or device coupler are used as disconnecting device, please
allow the disconnecting device to operate conveniently
Warning :
Instructions and procedures will be updated consistently according to the
product upgradation without subject to any prior notice. If any of the
instructions mentioned in the guide are not followed by the user, the loss will
be borne by the user. Instructions may contain technical inaccuracies or
inconsistencies with product functions and operations,or printing errors, in
accordance with the company's final interpretation.
Disclaimer :
The whole machine is made of all-metal material and has excellent heat
dissipation. The switch panel is powered by PoE port, uplink network port FE
and power indicator, PoE indicator is composed of uplink network signal
indicator. PoE Switch is widely used in public security, schools, residential
areas, office space and various inconvenient wiring scenarios to support PoE
power supply. PoE is Power Over Ethernet, referred to as Ethernet power
supply. This manual takes eight port PoE switch as an example to illustrate
the actual installation and application of the whole PoE series products.
Industrial Structure and Port Description :
Typical Application :
• Supports 2 *1000 Mbps uplink ports and 8 *1000 Mbps PoE ports.
• The switching capacity is 20 Gbps.
• Support IEEE802.3af, IEEE802.3at standard PoE total power 150W.
• MAC automatic learning and aging, the capacity of MAC address list is 8K.
• Port automatically adapts to MDI/MDIX mode.
• Support long distance up to 250 meters for data transmission & power supply.
• Support AC 110V, AC 240V power supply.
• Support lightning protection up to 6000V
Product Characteristics :
Equipment panel schematic :
A: PoE Network Port
C: Upper Interface
E: Power Interface
B: Extend Switch
D: Power Indicator
F: Ground Interface
**Please note:
1) When the extend switch is OFF, PoE devices will work maximum at
100meters with data transmission speeds to 1000Mbps. The devices
connected to the switch can ping each other
2) When the extend mode is ON, the PoE devices will work at 250meters
with data transmission speeds to 10Mbps. Devices on ports 1~8 port
devices can ping the only uplink port individually, but cannot ping each
other.
Please follow the following steps to install:
(1) Please disconnect the power supply of the equipment before installation.
Live installation may cause damage to transmission equipment.
(2) Check whether the network cables and other transmission lines to be
used are connected to the other equipment
(3) Connect DG-GS1010PF-B to the RJ45 interface and PoE network
camera with network cable.
(4) Connect the Uplink port to the NVR port with the network cable.
(5) Check whether the installation is correct, and the equipment is not
damaged to ensure that all connections are reliable, connect the power
cord and power the system.
(6) Verify that the network and PoE power supply are normal.
Extend 250 meters
Please follow the above installation steps from (1) (2) (3) (4)
(5) Push the "Extend" key to the "on" position
(6) Check whether the installation is correct or that the equipment is not
damaged, ensure that all connections are reliable, connect the power
cord and power the system
(7) Verify that the network and PoE power supply are normal
LED Description :
Indicator light Description
PWR LED Solid: Switch is powered On
Off: Switch is powered Off
Data LNK /
ACT LED
Solid: Network device is connected
Blinking: Data transmission
Off: No network device connected
PoE LED Solid: PoE device connected
Off: Not connected to network devices
Solid: Connect to network devices
Off: PoE device disconnected
Colour
Red
Green
Green
Uplink LED Green
Digisol is a Subsidiary of Smartlink Holdings Limited
www.digisol.com
L-7, Verna Industrial Estate,
Salcete, GOA - 403722
DIGISOL SYSTEMS LIMITED
1800 209 3444
Tabla de contenidos
Otros manuales de Cambiar de Digisol
Digisol
Digisol DG-GS4526P Manual de usuario
Digisol
Digisol DG-GS4900 SERIES Manual de usuario
Digisol
Digisol DG-GS1528HP/C Manual de usuario
Digisol
Digisol DG-CS4616F Manual de usuario
Digisol
Digisol DG-CS4554F Manual de usuario
Digisol
Digisol DG-GS4600 SERIES Manual de usuario
Digisol
Digisol DG-GS4110 Manual de usuario
Digisol
Digisol MUSTANG 4000 DG-FS4528 Manual de usuario
Digisol
Digisol DG-GS4200 Series Manual de usuario
Digisol
Digisol DG-GS1528HP/C Guía de inicio rápido
Digisol
Digisol DG-FS1526HP Manual de usuario
Digisol
Digisol DG-GS4824F Manual de usuario
Digisol
Digisol DG-FS4526E Manual de programación
Digisol
Digisol DG-GS1510HPEV2 Manual
Digisol
Digisol DG-GS1510HPEV2 Manual de usuario
Digisol
Digisol DG-FS4528P Manual de programación
Digisol
Digisol DG-GS1510PL Manual de usuario
Digisol
Digisol DG-CS4554F Manual de usuario
Digisol
Digisol DG-GS1016D-A Manual de usuario
Digisol
Digisol DG-GS4528SE Manual de programación
