Digimerge DPV24D Manual de usuario

Please read this manual thoroughly before use and keep it handy for future reference.

Vandal Models: DPV24D / DPV24TLX

Indoor Models: DPD23D / DPD24D

Ultra Resolution

Day & Night Dome Camera

INSTRUCTION MANUAL

INTRODUCTION

Features

All Models Feature:

• 1/3”SonySuperHAD™IICCD

• Excellentlowlightperformanceusing

 PolarisVision2technology.

• 0.15Lux/F1.2(Color)

 0.001Luxw/Sense-Upatx256

• 600TVlines(Color)ofresolution

• 3DDigitalNoiseReduction(3D-DNR)

• OSDmenucontrol

• PrivacyMasking/MotionDetection

• VIDEOOUT(BNC)

• Operatesin12VDCor24VAC

• TestMonitorOutput

• CameraMounting:Surface/Flushmounting

  (IndoorModelonly)

DPD23D

• IndoorDomeModel

• 3.6mmFixedLens

DPD24D

• IndoorDomeModel

• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris

DPV24D

• VandalResistantDomeModel

• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris

DPV24TLX

• VandalResistantDomeModel

• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris

• SmartIRtechnology

• ICRltertogiveclearnightvision

• ArcticProtechnologywithbuilt-inheater

• 0LuxwithIRLED

General DPD23D DPD24D DPV24D DPV24TLX

Power source DC 12V / AC 24V +10%

Power consumption 2.5 Watts 10 Watts

(Heater On)

Image sensor 1/3”SonySuperHAD™IICCD

Total pixels 811 (H) x 508 (V)

Scanning system 2:1 interlace

Scanning frequency 15.734KHz(H), 59.95Hz(V)

Sync.system Internal / Line Lock

Resolution 600 TV Lines

Min.Illumination 0.15Lux / 0.001Lux

Sense Up at x256 0 Lux IR LED On

Video output 1.0 Vp-p (75 ohm, composite)

S/N Ratio more than 50dB (AGC OFF)

Operating Temperature -10°C - +50°C -40°C - +50°C

Power input 2-Pin terminal block (Detachable)

Video output BNC Connector (2nd video RCA)

Lens mount Fixed mount

Lens 3.6mm Fixed 2.8 - 10.5mm F1.4 Varifocal DC Auto iris

Operating humidity 0-90% (non-condensing)

SPECIFICATIONS

-1-

-2-

MEASUREMENTS

Vandal Dome Dimensions

3/4’’ -14

NPS thread

97.0 mm

3.82 in

Base hole positions

40 mm

1.57 in

55.5 mm

2.19 in

Ø 0.1"

3.5 mm

3.9"

100.0 mm

3.4"

87 mm

5.1"

130 mm

112 mm

4.4 in

112 mm

4.4 in

39 mm

1.5 in

115 mm

4.5 in

27 mm

1.1 in

137°

123°

100°

7 mm

.28 in

Underside Base hole positionsIndoor Dome Dimensions

Recess cutout and tting clearance.Recess Mount Fitting dimensions

5.1"

130 mm

-3-

PACKING CONTENTS

Indoor Dome package contains the following:

Camera in housing ---------------------------------1

Camera Locking screws (PA3 Type) -----------2

Instruction guide (This Document)-------------1

Surface & Flush Mounting Templates----------2

RCA - BNC test cable------------------------------1

Junction Box Plate----------------------------------1

Mounting screw pack ------------------------------1

Vandal Dome package contains the following:

Camera in housing ---------------------------------1

Camera Locking screws (PM4 Type) ----------3

Instruction guide (This Document)-------------1

Surface Mounting Template ----------------------1

RCA - BNC test cable------------------------------1

Junction Box Plate----------------------------------1

Mounting screw pack ------------------------------1

Tamper allen key------------------------------------1

Conduit Key ------------------------------------------1

Junction box plate allows tting of either Vandal dome or

Indoor dome to standard 2S, 4S and Octagon junction

boxes.

NOTE: Flush side of junction box plate should be attached

to junction box

Junction Box tting plate accessories:

Junction Box Fitting plate ------------------------1

2S / 4S plate screws (KM3.5 Type) ------------4

Octagon tting screws (KM4 Type)-------------2

Base Fitting Screws PWM3 ----------------------3

JUNCTION BOX PLATE

Screw hole overview Vandal dome tting illustration Junction box tting plate attached to camera

Base Fitting

Screws

88.9 mm

3.5 in

83.3 mm

3.28 in

46.0 mm

1.8 in

Base Fitting

Screw.

Octagon

Screw

2S / 4S

Screw

Locking

Screw

Conduit

Key

Allen Key

Mounting Screws Pack.

3pc 70mm / 2.8in Screws

3pc 30mm / 1.2in Screws

3pc 40mm 1.6in plugs

-4-

JUNCTION BOX INSTALLATION TYPES

2S FITTING

a. 2S Fitting requires only 2pcs of base

attachment screws.

Note: You have a reduced space in which

to hide cables using this type of

installation. Recommended for indoor

dome only.

TWO GANG FITTING

a. Two gang tting (switch box) requires 4pcs

of base attachment screws.

Note: A two gang provides the most robust

tting. Suitable for both indoor and

vandal domes.

4S FITTING

a. 4S Fitting requires 2pcs of base attachment

screws.

Note: Screws used for the 4S box are larger

compared to those used for the 2S (M4

type). Suitable for both indoor and

vandal domes

OCTAGON FITTING

a. 4” Octagon tting requires only 2pcs of

base attachment screws.

Note Screws used for the octagon tting

are larger compared to those used for

the 2S/4S (M4 type). Suitable for both

indoor and vandal domes

Cable

Entry

Screws

Cable

Entry

Screws

Cable

Entry

Screws

Cable

Entry

Screws

-5-

VANDAL DOME FITTINGS

Pendant Cap - model # MNTV2XPC

Replaces the need for the camera base.

Compatible with ceiling conduit installations

Pole Mount - model # MNTV2XPJunction Box Accessory - model # MNTV2XJ

Fits either wall mount and corner mount bracket.

Symmetrical so reversible for top or bottom

conduit.

Corner Mount bracket - model # MNTV2XR

Can t either Wall Bracket or Junction Box. Pendant Mount - model # MNTV2XC

Wall Mount - model # MNTV2XW

-6-

INSTALLATION. VANDAL DOME

1) Remove the three tamper screws using the provided

allen key. Size is standard T-15

Note: If you plan to use conduit tting, remove conduit

cap using the prodivded conduit key.

DPV24TLX ONLY

When using DC power, note the correct polarity stated on the

label attached to the power cord.

Note: If you plan on installing onto a junction

box, attach provided tting plate rst to

the junction box and then you attach the

camera base to the tting plate.

3a) Reinsert camera module into camera base

by ligning up the arrow notches, and turning

camera module clockwise to lock into place.

3b) Use the supplied three base locking screws to

secure camera base to camera module.

Go to step 4on page 7 to complete installation.

Method 1 - Direct Attach Install

2a) Use included mounting template to mark and pre-

drill the required holes. Use 2pc of the 2.8” screws

to mount the camera directly to the mounting

surface.

Remove (one base locking screw, used for shipping

purposes) and install the 3rd 2.8” screw.

Go to step 4on page 7 to complete installation.

Method 2 - Camera Base Install

Note: Use this method if installing onto junction box

plate.

2b) Remove the camera base by unscrewing the base

locking screw, and turn camera module approx. 5

degrees counter-clockwise to detach camera base

from the camera module. Now you install the base

to the correct holes as indicated on the mount

template using the 1.2” screws.

Otros manuales para DPV24D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Digimerge

Digimerge

Digimerge DPP12D Manual

Digimerge

Digimerge DPV14D Manual de usuario

Digimerge

Digimerge DNZ9320W Manual de usuario

Digimerge

Digimerge DNP5220E Manual de usuario

Digimerge

Digimerge Flir DBV44TL Manual de usuario

Digimerge

Digimerge DPV14W Manual de usuario

Digimerge

Digimerge DPV24D Manual de usuario

Digimerge

Digimerge DCB13TL Manual de usuario

Digimerge

Digimerge DCV23DL Manual de usuario

Digimerge

Digimerge DCBHR1535 Manual de usuario

Digimerge

Digimerge DPV24D Manual de usuario

Digimerge

Digimerge DCBHR1037 Manual de usuario

Digimerge

Digimerge DPZ16TO27 Manual de usuario

Digimerge

Digimerge DCV24DL Manual de usuario

Digimerge

Digimerge DNP5320E Manual de usuario

Digimerge

Digimerge DPV24DL Manual de usuario

Digimerge

Digimerge DPV24D Manual de usuario

Digimerge

Digimerge DPV34WL Manual

Digimerge

Digimerge DPD14T Manual de usuario

Digimerge

Digimerge DCV54DL Manual de usuario

Digimerge

Digimerge DCDHR2532 Manual de usuario

Digimerge

Digimerge DPV14D Manual de usuario

Digimerge

Digimerge DCS100033 Manual de usuario

Digimerge

Digimerge DCV13TL Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario