Digimerge DNZ9320W Manual de usuario

HIGH RESOLUTION DUAL-CODEC

WDR PTZ SPEED DOME NETWORK

CAMERA

DNZ9320W

Page 2

www.digimerge.com

DNZ9320W_Quick Installation Guide_En_R1

This installation guide provides instructions for installing the Digimerge DNZ9320W

High Resolution Dual-Codec WDR PTZ Speed Dome Network Camera. For all other

aspects of using the product, please refer to the user manual available at www.

digimerge.com or on the Installation CD included with this product.

PACKAGE CONTENTS

IMPORTANT!

This product must be installed in compliance with local laws and regulations.

Package Contents:

1 x High Resolution Dual-

Codec WDR PTZ Speed

Dome Network Camera

2 x Plastic Ceiling Mount Attachments

2 x Metal Ceiling Mount Attachments

1 x Package of Mounting Hardware (2 pieces)

1 x Two-Piece Power

Adaptor Kit

1 x Software CD with Quick Installation

Guide & Hardware Manual.

1 x hard copies of Quick Installation

Guide & Warranty Card

1 x 3ft Ethernet Cable

The ports on the Camera are located in a removable IP Board along the bottom

of the camera. Connections should be made before permanently attaching the

Camera to the ceiling.

The DIP Switches on the Camera are located on the base (underside) of the

camera. Please refer to the hardware manual for detailed instructions.

Connector Ports:

3 4 5

1 2 6 7

1. ETHERNET PORT

2. POWER / NET LED INDICATORS

3. AUDIO IN

4. RS-485 IN/OUT BLOCK

5. ALARM IN/OUT BLOCK

6. BNC VIDEO OUTPUT

7. POWER CONNECTOR

DNZ9320W_Quick Installation Guide_En_R1

www.digimerge.com

Page 3

1. Mounting the Camera:

A. Embedded (ﬂush) Mounting

B. Surface Mounting

2. Connections:

A. Power and Ethernet Connections

B. Optional Connections

3. Software installation & Network Conﬁguration

HARDWARE MOUNTING

Mounting the Camera:

The Camera can be mounted to a ceiling by either

Embedding (only the dome is visible) or Surface

Mounting (the entire assembly is visible).

MOUNTING WARNINGS:

• Conﬁrm that the mounting location can hold the

weight of the Camera and Assembly.

• USE A SAFETY WIRE IN COMBINATION WITH

AN EYE BOLT OR NUT (NOT INCLUDED) WHICH

IS INSERTED IN TO A STUD OR OTHER MAIN

SUPPORTING CEILING STRUCTURE TO

PREVENT THE CAMERA FROM MOVING (AFTER

YOU HAVE SECURED THE CAMERA TO THE

CEILING).

• Install the Camera in a location where more than

30cm (1 ft.) is available above the ceiling board.

• Install the Camera in a location where the ceiling

board is more than 4cm (1.5”) thick.

• Run all cables to the Camera Location before

permanent mounting.

EMBEDDED (FLUSH) MOUNTING

SURFACE MOUNTING

SAFETY WIRE (NOT INCLUDED)

Page 4

www.digimerge.com

DNZ9320W_Quick Installation Guide_En_R1

HARDWARE MOUNTING

Continued

1A. Embedded (ﬂush) Mounting:

Before starting the Mounting procedure, conﬁrm that

the ceiling can hold the weight of the camera. A Safety

Wire (not included) is also required.

i. Cut a hole in the ceiling 170mm (6.7”) in diameter.

ii. Attach the Mounting Ring to the Ceiling:

• Use the provided “Installation Template -

Embedded Type” to drill the screw holes.

• Conﬁrm that the ring is placed so that the ridge is

against the ceiling (and the indented screw holes

are facing opposite the mounting surface).

• Use the drywall plugs and screws, or machine

screws and bolts to install the ring to the ceiling.

iii. Attach the three (3) ‘L’ shaped hinges to the

Camera as shown in diagram 1Aiii.

iii

DNZ9320W_Quick Installation Guide_En_R1

www.digimerge.com

Page 5

iv. Connect the safety cable (not included) - make

sure the Camera is secure.

v. Connect the Power and Ethernet cables

(necessary) and any optional connection cables

to the Camera before inserting into the Ceiling.

vi. Insert the Camera Base into the ceiling hole.

Secure the Camera to the Ceiling Mounting

Ring using the three (3) provided screws.

vii. Twist on the Plastic Bracket Cover.

1B. Surface Mounting

Before starting the Mounting procedure, conﬁrm

that the ceiling can hold the weight of the camera.

A Safety Wire (not included) is required.

i. Afﬁx the Base to the Camera (if detached).

ii. Drill holes into the ceiling:

• Use the provided “Installation Template -

Attached Type” to drill the screw holes.

• Use the drywall plugs and screws, or machine

screws and bolts to install the ring to the ceiling.

iii. Connect the safety cable (not included) - make

sure the Camera is secure.

iv. Connect the Power and Ethernet cables

(necessary) and any optional connection cables

to the Camera before attaching the Base Cover.

v. Use the Plastic Base Cover to shield the

installation. Attach securely with three (3)

screws (provided).

HARDWARE MOUNTING

Continued

4i 4ii

Page 6

www.digimerge.com

DNZ9320W_Quick Installation Guide_En_R1

HARDWARE CONNECTIONS

Connections:

2A. Power and Ethernet Connections:

Make sure that the cables have been run to the

Camera Location prior to permanent mounting.

i. Connect the Ethernet Cable to the Ethernet Port on

the base of the Camera.

ii. Connect a Power Cable to the Camera.

NOTE: If using Optional Connections, connect the

Power Cable last.

2B. Connections:

The Optional Connections for the Camera include:

• BNC Video Out - Connects the Camera to an

independent TV or Monitor (additional BNC or

RCA adaptors may be needed - not included).

• Alarm IN/OUT Sensor Terminal Block - Connect

up to 6 incoming and 1 outgoing Alarm Sensors

(NC or NO type) - See Appendix #2 in the hardware

manual for Details.

• RS-485 Control Terminal Block - Connect a

Keyboard (not included) to control the Camera,

or use the connections to loop several cameras

together in series - See Appendix #2 in the hardware

manual for Details.

• Audio Input - Connects a microphone to the

Camera.

NOTE: If using Optional Connections, connect the

Power Cable last.

AUDIO BNC OUTPUT

Alarm IN/OUT RS-485 BLOCK

OPTIONAL

DNZ9320W_Quick Installation Guide_En_R1

www.digimerge.com

Page 7

SOFTWARE INSTALLATION

The Digiconsole application loads

from the CD included with your

package, and provides you with the

following:

1. Web links to various resources

and documentation

2. Discovery of all the Digimerge

IP devices on the network

3. Provides Network

conﬁguration of IP Devices

4. Installs DigiConsole and

Surveillance application on your

local PC

5. Warranty information and DDNS

registration

Digiconsole Utility screen consists of

the following menus:

1. Home

2. Find Devices

3. Register

4. Install

Page 8

www.digimerge.com

DNZ9320W_Quick Installation Guide_En_R1

Home:

Provides basic Digiconsole operating

instructions, links to product informa-

tion/documentation as well as 3rd party

software support links.

SOFTWARE SET-UP

Find Devices:

Locates all available Digimerge IP

devices on your network and displays

a snapshot of the results. Click on any

available device to display image on

the right side screen display.

NOTE: You may need to press the Find

Devices button several times as some

devices may not respond immediately.

If you do not see a camera image,

please check that all cables running

from the Camera are connected

properly.

Menu:

The Menu Button or right clicking on

a device icon provides access to

device speciﬁc settings:

• Edit Network Parameters

• View Live Image

• Open Device in Browser

• Update Firmware in Video Device

• Refresh the device list - in order to

remove inactive and disconnected

devices

NOTE: It is recommended that you

record the device speciﬁc MAC and

IP address for DDNS registration

purposes. If you have multiple

cameras on a local network, only

one camera needs to be conﬁgured

for DDNS.

MAC:

IP:

DNZ9320W_Quick Installation Guide_En_R1

www.digimerge.com

Page 9

SOFTWARE SET-UP

Edit Network Parameters:

The Network Parameters are

automatically assigned to the

Device by the network router (by

using DHCP). These settings can

be manually changed if desired.

1. Select the IP device you would

like to edit by clicking on its icon.

2. Click on the MENU button or

right click the icon for the device

to access the menu. Select

“Edit Network Parameters” from

the menu.

3. Make the necessary changes

and click OK to save changes or

click CANCEL to close the

window without saving any of the

changes made.

NOTE: If a user name and password

were set-up on the IP Device previ-

ously, you will be required to enter

this authentication information when

attempting to access the device.

View Live Image:

View live video from the IP Device

using the Apple QuickTime program.

If this application is not installed on

your system, please download it at

http://www.apple.com/QuickTime

OPTIONAL

If by clicking VIEWING LIVE IMAGE

the image is not automatically shown

in QuickTime, follow these steps in

QuickTime:

1. Go to FILE

2. Choose OPEN URL

3. Enter the following: rtsp://<device

IP address> (i.e. rtsp://192.168.2.102)

A device IP address can be obtained

from the Digiconsole device list.

NOTE: Minimum QuickTime version installed

should be 7.1.6. If you cannot install Quick-

Time, use Microsoft Internet Explorer to view

the device. See step C3 for details.

Continued

Page 10

www.digimerge.com

DNZ9320W_Quick Installation Guide_En_R1

SOFTWARE SET-UP

Open Device in Browser:

Opens up the DigiViewer Video Browser

using your default web browser (e.g.

Internet Explorer).

Once user names and passwords are set up

by the administrator, the users (except for

a VIEWER level user) are required to enter

this information every time they access the

DigiViewer.

Click (during streaming mode)

to mute the audio.

Click to capture a snapshot image

in a new browser window.

By default, the image refresh rate

is set to OFF. Move slider to the

right to set image refresh rate.

Click to bring up image brightness and contrast controls

Click to capture a video clip and send it to a FTP site. FTP

must be conﬁgured in the SETTINGS screen

Click here to start streaming video

Continued

The DigiViewer application is a Live View /

Remote Access application that allows you to

access the IP Device directly from any com-

patible web browser. Any settings that are

changed in the DigiViewer are directly altering

the camera and not the application.

The DigiViewer browser allows the user

to view streaming video from the device

as well as change certain settings on the

device depending on the level of access

set by the administrator.

Otros manuales para DNZ9320W

Tabla de contenidos

Otros manuales de Cámara de seguridad de Digimerge

Digimerge

Digimerge DPV24DL Manual de usuario

Digimerge

Digimerge DPZ16TO27 Manual de usuario

Digimerge

Digimerge DPB14TLX Manual de usuario

Digimerge

Digimerge DPZ36WO23 Manual de usuario

Digimerge

Digimerge DBD14 Manual de usuario

Digimerge

Digimerge DPD23D Manual de usuario

Digimerge

Digimerge DCBHR1035 Manual de usuario

Digimerge

Digimerge DPV14W Manual de usuario

Digimerge

Digimerge DPV24DL Manual de usuario

Digimerge

Digimerge DPV34D Manual de usuario

Digimerge

Digimerge DPP12D Manual

Digimerge

Digimerge DPV14D Manual de usuario

Digimerge

Digimerge DNB6300V Manual de usuario

Digimerge

Digimerge DPD24W Manual

Digimerge

Digimerge DCS100033 Manual de usuario

Digimerge

Digimerge DNP5220E Manual de usuario

Digimerge

Digimerge DNP5320E Manual de usuario

Digimerge

Digimerge DCBHR1535 Manual de usuario

Digimerge

Digimerge DPD14T Manual de usuario

Digimerge

Digimerge DCB13TL Manual de usuario

Digimerge

Digimerge Flir DBV44TL Manual de usuario

Digimerge

Digimerge DCV24DL Manual de usuario

Digimerge

Digimerge DPP22W Manual

Digimerge

Digimerge DCDHR2532 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario