DFI WB72-SC Manual de usuario

WB72-SC

WB72-SR

Rev. A+

System Board Users Manual

Carte Mère Manuel Pour Utilisateur

System-Platine Benut erhandbuch

Manual del Usuario de Placas Base

51310136

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows® 98, Windows® 98 SE, Windows® ME, Windows® 000

and Windows NT® 4.0 are registered trademarks of Microsoft

Corporation. Intel® and Pentium® 4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Quick Setup Guide



Quick Setup

Guide

Table of Contents

Chapter 1

Quick Setup Guide.............................................

Chapter 2

En lish......................................................................

Chapter 3

Français (French).................................................

Chapter 4

Deutsch (German)................................................

Chapter 5

Español (Spanish)..................................................



Quick Setup Guide

Quick Setup

Guide

Chapter 1 - Quick Setup Guide

Table of Contents

1.1 System Board Layout..................................................................................................

1. Jumpers.....................................................................................................................................

1.3 Ports and Connectors................................................................................................

1.4 Award BIOS Setup Utility.......................................................................................

Note:

The users manual in the provided CD contains detailed information

about the system board. If, in some cases, some information doesnt

match those shown in this manual, this manual should always be

regarded as the most updated version.

Quick Setup Guide



Quick Setup

Guide

1.1 System Board Layout

WB72-SC



Quick Setup Guide

Quick Setup

Guide

WB72-SR

(Supports AID)

Quick Setup Guide



Quick Setup

Guide

1.2 Jumpers

1.2.1 Clear CMOS Data - JP6

-3 On:

Clear CMOS Data

1- On:

Normal (default)

1.2.2 Wake-On-Keyboard / Wake-On-Mouse - JP1

1- On:

Disable the Wake-On-

KB/Mouse function

(default)

-3 On:

Enable the Wake-On-

KB/Mouse function

Important:

The 5VSB power source of your power supply must support

≥

720mA.

1 3

3 1



Quick Setup Guide

Quick Setup

Guide

1.2.3 Wake-On-USB Keyboard - JP2 and JP5

Important:

 If you are using the Wake-On-USB Keyboard function for 2 USB

ports, the 5VSB power source of your power supply must

support

≥

1.5A.

 If you are using the Wake-On-USB Keyboard function for 4 USB

ports, the 5VSB power source of your power supply must

support

≥

2A.

-3 On:

Enable the

Wake-On-USB KB

1- On:

Disable the

Wake-On-USB KB

(default)

JP2 - for the USB keyboard that is connected to the USB 1 or USB

port.

JP5 - for the USB keyboard that is connected to the USB 3 or USB 4

port.

USB KB Wake-Up From S3 in the Power Management Setup submenu

of the BIOS must also be enabled.

Quick Setup Guide



Quick Setup

Guide

1.2.4 USB 4 Select - JP8 and JP9

1- On:

USB 4 on J16

(default)

-3 On:

USB 4 on CNR

JP9 JP8

Otros manuales para WB72-SC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario