DFI 865PE-ML Manual de usuario

865PE-ML

Rev. C+

System Board

User’s Manual

78110352

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. Intel®and Pentium®4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's author-

ity to operate the equipment.

2. Shielded interface cables must be used in order to comply

with the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Hyper-Threading Technology Functionality Requirements..........

1.3 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 CPU Frequency Control............................................................

3.1.8 Load Fail-Safe Defaults.....................................................................

3.1.9 Load Optimized Defaults..............................................................

3.1.10 Set Supervisor Password...............................................................

3.1.11 Set User Password..............................................................................

3.1.12 Save & Exit Setup.................................................................................

3.1.13 Exit Without Saving..............................................................................

3.2 Updating the BIOS.....................................................................................................

Introduction

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.................................................................

4.2 Drivers, Utilities and Software Applications.....................................

4.3 3D Audio Configuration....................................................................................

4.4 Installation Notes......................................................................................................

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...........................................

Appendix B - System Error Messages

B.1 POST Beep....................................................................................................................

B.2 Error Messages...........................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist.................................................................................

104

107

108

111

113

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®865PE chipset

- Intel®865PE Memory Controller Hub (MCH)

- Intel®82801EB I/O Controller Hub (ICH5)

Processor

The system board is equipped with Socket 478 for installing one of

the following supported processors.

• Intel®Pentium®4 (Prescott and Northwood) processor up to

3.2GHz+

- Intel Hyper-ThreadingTechnology

- FSB: 533MHz and 800MHz

• Intel®Celeron®processor

- 400MHz system data bus

Note:

Refer to section 1.2 and appendix A for more information on

the Hyper-Threading Technology.

System Memory

• Two 184-pin DDR DIMM sockets

• Supports dual channel (128-bit wide) memory interface

• Supports up to 2GB system memory

• Synchronous operation with processor system bus

- PC2700/PC3200 (DDR333/DDR400) with 800MHz FSB

CPU. DDR333 will run at 320MHz memory frequency when

used with 800MHz FSB CPU.

- Use PC2100/PC2700 (DDR266/DDR333) with 533MHz

FSB CPU

- Use PC2100 (DDR266) with 400MHz FSB CPU

Chapter 1 - Introduction

Introduction

Density Width

Single/Double

184-pin DDR

64 Mbit

SS/DS

64/128MB

X16

SS/DS

32MB/NA

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/NA

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/NA

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/NA

Expansion Slots

The system board is equipped with 1 AGP slot and 3 PCI slots.

AGP (Accelerated Graphics Port)

• Supports AGP 3.0 (AGP 4x and 8x) and AGP 2.0 (AGP 1x and

4x) spec.

• Supports 1.5V AGP 8x (2.13GB/sec.) and AGP 4x (1066MB/

sec.) add-in cards.

AGP is an interface designed to support high performance 3D

graphics cards for 3D graphics applications. It handles large

amounts of graphics data with the following features:

• Pipelined memory read and write operations that hide

memory access latency.

• Demultiplexing of address and data on the bus for nearly

100 percent efficiency.

Note:

AGP 2x and 3.3V AGP cards are not supported.

Onboard Audio Features

• 20-bit stereo full-duplex codec with independent variable sam-

pling rate

• High quality differential CD input

• True stereo line level outputs

• S/PDIF-in/out interface

• 6-channel audio output

• Supports non-ECC (x64) DIMM using 128Mb, 256Mb or

512Mb

• Supports unbuffered DIMMs

Introduction

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio

The 6-channel audio output function is supported by using the

surround connector, the audio jacks at the rear panel and configuring

the audio driver. Please refer to chapters 2 and 4

Onboard LAN Features

• Uses Realtek RTL8101L fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Compatibility

• PCI 2.2 and AC ’97 compliant

• Intel AGP version 3.0

SATA (Serial ATA) IDE Interface

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification (1.5Gbps interface)

Introduction

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wire-

less connectivity between your computer and peripheral devices.

The IRDA (Infrared Data Association) specification supports data

transfers of 115K baud at a distance of 1 meter.

USB Ports

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1

supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device

transfer speeds between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®98SE/2000/ME/XP Plug and Play

compatible

• CPU/DRAM overclocking in 1MHz stepping

• AGP/PCI/SATA overclocking

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 4Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on

using the DMI utility.

Tabla de contenidos

Otros manuales de Placa madre de DFI

DFI

DFI G586IPV Manual de usuario

DFI

DFI HR100-CRM Manual de usuario

DFI

DFI AL701 Manual de usuario

DFI

DFI WL051-BCC-B Manual de usuario

DFI

DFI HD330-Q87 Manual de usuario

DFI

DFI AK70 Manual de usuario

DFI

DFI CS62-TC Manual de usuario

DFI

DFI LanParty 925X-T2 Manual de usuario

DFI

DFI CR100-CRM Manual de usuario

DFI

DFI HD330-H81 Manual de usuario

DFI

DFI PT332-DRM Manual de usuario

DFI

DFI CB60-ZX Manual de usuario

DFI

DFI CA64-TC Manual de usuario

DFI

DFI LanParty UT nF3 Ultra-D Manual de usuario

DFI

DFI G4S601-B Manual de usuario

DFI

DFI ST2K Series Manual de usuario

DFI

DFI PE11-TC Manual de usuario

DFI

DFI ICX610-C621A-000G Manual de usuario

DFI

DFI AM33-EC Manual de usuario

DFI

DFI ADS101 Manual de usuario

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Manual de usuario

DFI

DFI KD331-C236/Q170 Manual de usuario

DFI

DFI COM630-B Manual de usuario

DFI

DFI AD73 Pro Manual de usuario

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario