DFI ST101-SR Manual de usuario

1/9

1. Make sure the system and all other peripheral devices connected to it has been

powered-off.

2. Disconnect all power cords and cables.

ST101-SR

Installation Guide

Removing the Chassis Cover

3. The screw at the rear panel is

used to secure the cover to the

chassis. Remove the cover screw

then put it in a safe place for later

use.

4 Lift the cover by first pulling it

backward (1) then lifting it up (2).

Side view

(2)

(1)

1. The drive bay bracket is readily

accessible when you remove the

cover.

Removing the Drive Bay Bracket

Drive bay

bracket

2/9

3. The drive bay bracket will

resemble the one shown on the

right.

2. The 4 screws are used to secure

the drive bay bracket. Remove

these screws and put them in a

safe place for later use.

Side view

Top view

Top of drive bay bracket

(for optical drive)

Bottom of drive bay bracket

(for SATA drive)

3/9

1. Position the SATA drive at the

bottom side of the drive bay

bracket.

2. To secure SATA to the drive bay

bracket, you must fasten screws

from the top side of the drive

bay bracket.

While holding the SATA drive in

place, turn the drive bay bracket

to the top side then adjust the

drive so that the mounting holes

on the drive match the mounting

holes on the bracket. Now secure

the drive by fastening 4 screws.

Screw

Installing the SATA and Optical Drives

Screw

SATA power

connector

SATA data

connector

Rear view of the SATA drive

4/9

3. After fastening the screws, on the

same side of the bracket (top

side), position the optical drive as

shown on the right.

4. Secure the optical drive by

fastening screws on each side of

the drive bay bracket.

IDE data

connector

IDE power

connector

Optical drive

SATA

5. These cables are used to connect

the SATA and optical drives to

the system.

SATA data cable

(for SATA drive)

40-pin IDE data cable

(for optical drive)

Rear view of the optical drive

SATA Optical drive

SATA power cable

(for SATA drive)

5/9

6. The figure on the right shows the

locations of the SATA and IDE

connectors on the system board.

7. Connect one end of the SATA

and IDE data cables to their

respective connectors.

SATA data cable

IDE data cable

40-pin IDE

connector

SATA

connector

8. Connect "A" of the SATA power

cable to the "B" connector of the

power supply unit.

Connected

to the power

supply unit

SATA power cable

6/9

10. Turn the drive bay bracket to the

top side. Insert the IDE power

cable (from the system’s power

module) and the other end of

the IDE data cable through the

bracket’s hole, up to the top side

of the bracket.

Connect the IDE power cable to

the power connector at the rear

of the optical drive.

11. Connect the other end of the

IDE data cable to the IDE

connector at the rear of the

optical drive.

IDE

power

cable

IDE

data

cable

IDE data cable

9. Connect the other end of the

SATA data cable to the SATA

drive.

Connect the other end of the

SATA power cable to the power

connector at the rear of the SATA

drive.

SATA power cable

SATA data cable

7/9

12. Insert the drive bay bracket from

the side of the system.

13. Secure the drive bay bracket by

fastening the screws you

removed earlier.

14. Replace the chassis cover and

secure it with the screw you

removed earlier.

15. Insert the provided power cord

holder. This will prevent the cord

from falling off easily or detach-

ing from the system.

Power cord

holder

Insert holder here

16. When you power up the system, configure the drives in the BIOS. Refer to the sys-

tem board manual in the provided CD.

17. Refer to the manual or documentation enclosed with the drives for additional infor-

mation on using the drive.

8/9

2. The mounting holes are located

at the bottom of the system.

Mount the mounting rails on each

side of the system using the

provided mounting screws.

Mounting rail Mounting rail

3. Mount the whole system on the

wall by fastening screws through

the rail's mounting holes.

Rail's mounting hole

Note:

The pictures in this document are for illustration only. The system board and all

other components may differ depending on the configuration you have purchased.

Please refer to the provided CD for details relevant to the system board.

Rail's mounting hole

Rail's mounting hole Rail's mounting hole

Mounting ST101-SR

The ST101-SR package includes mounting rails (optional) that can be used for mount-

ing the system on the wall.

1. If rubber feet has been

previously attached at the

bottom of the system, please

remove them first.

9/9

934-ST1011-000G

AST101SR10834

Package Contents

•One ST101 unit

•One 120W power adapter (the power cord must be purchased separately

according to your area's requirement)

•One utility CD

•One installation guide

•One QR

•One 40-pin IDE cable

•One ST101 chassis parts kit

•Two L-shaped brackets for wall-mounting

•One SATA cable

•One SATA power cable

Otros manuales para ST101-SR

Tabla de contenidos

Otros manuales de Hardware de computadora de DFI

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario