Dell PowerConnect 2708 Documento técnico

Appendix A: Configuration Examples

This Appendix provides some configuration examples for the PowerConnect 2708/2716/2724

devices installed in the Enterprise Network.

The following configuration scenarios are described:

• Configuring Interface Parameters

• Creating VLAN Membership

• Configuring VLAN Port Settings

• Configuring LAG Membership

• Downloading Software File

• Configuring Port Mirroring

• Configuring Storm Control

• Configuring CoS Priority Queues

www.dell.com | support.dell.com

Configuring Interface Parameters

The Interface Configuration screen enables the user to set the various interface parameters,

interface type and additional operational attributes. In the following example, Port 1 is configured

as 1000Mbps Copper interface type, as maximum speed and interface media type. The appropriate

cable type connection is RJ-45 1 Gigabit connection.

The Admin Status is Enabled, therefore traffic is forwarded through the port. The Current

Interface Speed is 10 Mbps as the actual synchronized interface speed. The Admin Duplex mode is

Full Duplex (FDX), supporting transmission in both directions, while the Current Duplex Mode is

configured at Half Duplex (HDX), supporting transmission between the device and the other

station in one direction only. Auto-Negotiation is Enabled, Backpressure is set at Disable, and Flow

Control is set at Disable.

Figure 9-1. Interface Configuration

VLANs

VLANs are logical subgroups within a Local Area Network (LAN) that combine user stations and

network devices into a single brodcast domain, regardless of the physical LAN segment to which

they are attached.

VLANs allow network traffic to flow more efficiently within subgroups. VLANs managed through

software reduce the amount of time network changes, additions, and moves are implemented. Port-

based VLANs are comprised of a set of ports that make up a Layer 2 broadcast domain.

The following figure illustrates the concept of VLANs in the Enterprise Network. In this example,

Finance, Marketing and R&D departments are configured as three distinct VLANs in the

enterprise, designated as VLAN #2, VLAN#3 and VLAN#4, respectively.

Figure 9-2. Port-Based VLANs in the Enterprise

Creating VLAN Membership

VLANs are collections of switching ports that comprise a single broadcast domain. Packets are

classified as belonging to a VLAN based on either the VLAN tag, or a combination of the ingress

port and packet contents. Packets sharing common attributes can be grouped in the same VLAN.

VLAN tagging provides a method of transferring VLAN information between VLAN groups. VLAN

tagging attaches a 4-byte tag to packet headers. The VLAN tag indicates to which VLAN the packet

belongs. VLAN tags are attached to the packets by either the end station or by the network device.

VLAN tags also contains VLAN network priority information.

VLAN membership is used to partition traffic into several mutually exclusive broadcast domains.

VLAN membership facilitates greater security and pre-defined access levels of user groups in

separate departments.

The VLAN Membership

Web Management page contains fields for defining VLAN groups. The

device supports the mapping of 4094 VLAN IDs to 64 VLANs. All ports must have a defined PVID.

If no other value is configured the default VLAN PVID is used. VLAN ID #1 is the default VLAN,

and cannot be deleted from the system.

The VLAN Membership screen enables the user to select an existing VLAN, create a new VLAN

with port numbers, create a new VLAN port membership, or remove an existing VLAN.

VLAN Membership ports can be defined as Untag Egress packets, Tag Egress packets, or they can

be defined as Not Member.

www.dell.com | support.dell.com

Figure 9-3. VLAN Membership

Defining VLAN Port Settings

The VLAN Port Settings screen enables the user to configure information for a specific port in a

LAG. In the following example, port #2 in LAG Group 1, has the Frame Type as Admit All, and

Ingress Filtering is Disabled.

The follwing screen shows the specific status information relevant to a specific port, and global

status information relevant to all ports.

Figure 9-4. VLAN Port Settings

LAGs

A Link Aggregated Group (LAG) is composed of ports with the same speed, set to full-duplex

operation. Up to six Aggregated Links may be defined, each with up to four member ports, to form

a single Link Aggregated Group (LAG). This enables:

• Fault tolerance protection from physical link disruption

• Higher bandwidth connections

• Improved bandwidth granularity

• High bandwidth server connectivity

With the departmental PowerConnect 2708/2716/2724 switches installed, network redundancy and

improved traffic performance are facilitated. The PowerConnect device serves to connect the

departmental groups of users to another switch that is located on another floor. In addition, LAGs

are used to ensure that a backup, in case one line is disabled.

The following figure illustrates the concept of Aggragated Links in the switch.

www.dell.com | support.dell.com

Figure 9-5. LAGs in the PowerConnect Departmental Switch

Aggregating Ports

Link Aggregation optimizes port usage by linking a group of ports together to form a single LAG

(aggregated group). Aggregating ports multiplies the bandwidth between the devices, increases

port flexibility, and provides link redundancy.

Consider the following when aggregating ports:

• Link Aggregation is allowed between two devices only.

• All ports within a LAG must be the same media type.

• A VLAN is not configured on the port.

• The port is not assigned to a different LAG.

• An available MAC address exists which can be assigned to a port.

• Auto-negotiation mode is not configured on the port.

• The port is in full-duplex mode.

• All ports in the LAG have the same ingress filtering and tagged modes.

• All ports in the LAG have the same back pressure and flow control modes.

• All ports in the LAG have the same priority.

• All ports in the LAG have the same transceiver type.

• The device supports up to six LAGs, and up to four ports in each LAG.

Ports added to a LAG do not their individual port configuration. When ports are removed from the

LAG,

the original port configuration is applied to the ports.

The device considers an Aggregated

Link a single logical port.

Configuring LAG Membership

The following screen shows an example of Link Aggregation configuration, whereby LAG Group 4

consists of member ports 5, 6, and 7.

Figure 9-6. LAG Membership

Downloading Files from Server

The File Download screen enables the user to configure and update Software Image files or BootP

Image files in the PowerConnect 2708/2716/2724 devices.

The TFTP Server IP Address specifies the location from which files are donloaded. The File Name

specifies the file to be downloaded. The Destination File can be either the Software Image file, or

the Boot Code image.

NOTE: The TFTP Server application can be either downloaded from Internet public domains, or purchased

from software vendors.

www.dell.com | support.dell.com

Figure 9-7. File Download

Port Mirroring

PowerConnect 2708/2716/2724 support port mirroring functionality. Port Mirroring allows traffic to

be copied from one port to another port. Port mirroring monitors and mirrors network traffic by

forwarding copies of incoming and outgoing packets from a monitored port to a monitoring port.

The user can specify which target port receives copies of all traffic passing through a specified

source port.

The Port Mirroring feature enables the Network Administator to perfom network monitoring and

debugging, detecting and troubleshooting network traffic problems, faulty NICs, and isolating

communication problems in the network.

The following figure illustrates the concept of Port Mirroring. In this example, port 7 is the Source

Port in the device, and port 3 is the Destination port. In this scheme, the Destination Port monitors

and copies all incoming and outgoing traffic on the Source Port. The Network Administrator can

connect to port 3 a sniffer or some other network traffic analyzer.

Figure 9-8. Port Mirroring Setup with Departmental Switch

In the following screen, the Destination Port is configured as port 3, and the Source Port as port 7.

The type of traffic to be monitored is configured as Tx (Transmit) and Rx (Receive). The user can

elect to add/remove ports to be mirrored and monitored on the network, as required.

Figure 9-9. Port Mirroring

www.dell.com | support.dell.com

Storm Control

Enabling Storm Control

The Storm Control mechanism is useful when a faulty Network Interface Card (NIC), or Broadcast

or Multicast frames cause network flooding, beyond the threshold rate limit. When Layer 2 frames

are forwarded, Broadcast and Multicast frames cause flooding to all ports on the relevant VLAN.

This occupies bandwidth, and loads all nodes connected on all ports.

The Network Administrator moderates the network traffic by setting the threshold so as to limit, or

disables the Storm Control operation, therefore limiting the amount of Multicast and Broadcast

frames accepted and forwarded by the PowerConnect 2708/2716/2724 device.

In the example shown in the following screen, the Broadcast Rate Threshold is configured to 1000

packets per second. Count Multicast with Broadcast is Enabled, and Broadcast Control is Enabled.

NOTE: The threshold rate limit is defined by the Network Administrator, according to the characteristics of the

network to be monitored, and the applications running on the network.

NOTE: The Storm Control screen below applies to the PowerConnect 2716 and PowerConnect 2724 devices.

Figure 9-10. Storm Control

Otros manuales para PowerConnect 2708

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Dell

Dell

Dell Force10 Z9000 Manual de usuario

Dell

Dell PowerEdge 1855 Manual de usuario

Dell

Dell PowerConnect 6224 Manual de usuario

Dell

Dell PowerConnect 6224 Instrucciones de funcionamiento

Dell

Dell S6000-ON Manual de usuario

Dell

Dell 5324 - PowerConnect Switch Manual de instrucciones

Dell

Dell PowerConnect 2016 Guía del usuario

Dell

Dell PowerConnect 6024 Manual de usuario

Dell

Dell N1100-ON Manual de usuario

Dell

Dell Networking Z9500 Manual de usuario

Dell

Dell N2128PX-ON Instrucciones de montaje

Dell

Dell PowerConnect 54 Series Manual de usuario

Dell

Dell PowerConnect 3324 Manual de usuario

Dell

Dell 3500 Series Manual de usuario

Dell

Dell EMC S5000 Manual de usuario

Dell

Dell PowerConnect 2808 Manual de usuario

Dell

Dell POWERCONNECT 5548P Manual de usuario

Dell

Dell EMC PowerSwitch S6100-ON Manual de usuario

Dell

Dell PowerConnect 6224 Manual de usuario

Dell

Dell N2000 Series Manual de usuario

Dell

Dell PowerVault 50F Manual de usuario

Dell

Dell PowerEdge M420 Manual de usuario

Dell

Dell PowerConnect 3324 Manual de usuario

Dell

Dell PowerConnect J-EX4200-24T Guía de inicio rápido

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario