Dell X1000 Series Manual de usuario

Dell™ Networking™ X1000

and X4000 Series Switches

Getting Started Guide

使用入门指南

入門指南

Panduan Pengaktifan

はじめに

시작 안내서

Dell™ Networking™ X1000

and X4000 Series Switches

Getting Started Guide

Regulatory Models: X1008, X1008P, X1018,

X1026, X4012, X1018P, X1026P, X1052,

X1052P

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your device.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions.

All other marks and names mentioned herein may be trademarks of their respective companies.

P/N RF9YW Rev. A00

Getting Started Guide 3

Welcome

This document provides basic information to install and start running the

following Dell Networking X-series switches: X1008/X1008P, X1018/X1018P,

X1026/X1026P, X1052/X1052P and X4012.

The switch is delivered from the factory in Unmanaged Mode to avoid

unauthorized access to the switch. To use the switch in Managed Mode,

press the Mode button for at least seven seconds. The MGMT LED will

illuminate when in Managed Mode. To switch back to Unmanaged Mode,

repeat the process.

These Dell networking devices are ideal for the small to medium business

that requires high performance network connectivity along with advanced

web management features. The management features are designed to

minimize administrative management effort, while enhancing and improving

network traffic control.

For the latest documentation and software updates, go to dell.com/support.

Safety Environmental and Regulatory Information (SERI) is included in the

printed documentation.

Package Contents

While unpacking the device, make sure that the following items are included:

• The ordered network switch

• AC power cable (and power brick only for the X1008 and X1008P)

• Console micro-USB serial cable

• Self-adhesive rubber pads (for desk or shelf installation on select systems)

• Installation kit

• Safety Environmental and Regulatory Information document

•Placemat

• This Getting Started Guide

4Getting Started Guide

X1000 and X4000 Series Switches Summary

Mounting the Device

Rack Installation

WARNING: Read the safety information in SERI as well as the safety information

for other switches that connect to or support the switch.

WARNING: Disconnect all cables from the switch before mounting the switch in

a rack or cabinet.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

Install the switch in a rack with brackets as follows (52 port switches have

a ready rail kit):

Place the supplied rack-mounting bracket on one side of the switch

making sure the mounting holes on the switch line up to the mounting

holes on the rack mounting bracket.

Table 1-1. X1000 and X4000 Series Switches Summary

Marketing Model

Name

Power Supply Unit Regulatory Model

Number

Regulatory Type

Number

X1008 External, 24W E08W E08W001

X1008P External, 150W E09W E09W001

X1018 Internal, 40W E10W E10W001

X1026 Internal, 40W E10W E10W002

X4012 Internal, 100W E10W E10W003

X1018P Internal, 280W E11W E11W001

X1026P Internal, 450W E11W E11W002

X1052 Internal, 100W E12W E12W001

X1052P Internal, 525W E12W E12W002

Getting Started Guide 5

Figure 1-1. Bracket Installation for Rack Mounting

Insert the supplied screws into the rack mounting holes and tighten with

a screwdriver.

Repeat the process for the rack-mounting bracket on the other side of

the switch.

Insert the switch into the rack, making sure the rack-mounting holes on

the switch line up to the mounting holes on the rack.

Secure the switch to the rack with the rack screws (not provided).

Fasten the lower pair of screws before the upper pair of screws.

Make sure that the ventilation holes are not obstructed.

Flat Surface Installation

The switch can be installed on a flat surface if it is not installed on a rack.

The surface must be able to support the weight of the switch and the

switch cables.

Attach the self-adhesive rubber pads (provided with the switch) on each

marked location on the bottom of the chassis.

Set the switch on a flat surface, while leaving two inches (5.08 cm) on each

side and five inches (12.7 cm) at the back.

Make sure that the switch has proper ventilation.

6Getting Started Guide

Wall Installation

To mount the switch on a wall:

Make sure that the mounting location meets the following requirements:

• The surface of the wall must be capable of supporting the switch.

• Allow at least two inches (5.1 cm) space on the sides for proper

ventilation and five inches (12.7 cm) at the back for power

cable clearance.

• The location must be ventilated to prevent heat buildup.

Place the supplied wall-mounting bracket on one side of the switch,

verifying that the mounting holes on the switch line up to the mounting

holes on the wall-mounting bracket.

Figure 1-2. Bracket Installation for Wall Mounting

Insert the supplied screws into the wall-mounting bracket holes and

tighten with a screwdriver.

Repeat the process for the wall-mounting bracket on the other side of

the switch.

Place the switch on the wall in the location where the switch is being installed.

On the wall mark the locations where the screws to hold the switch must

be prepared.

Getting Started Guide 7

On the marked locations, drill the holes and place all plugs (not provided)

in the holes.

Secure the switch to the wall with screws (not provided). Make sure that

the ventilation holes are not obstructed.

Starting and Configuring the Switch

Management Modes

The Dell Networking X1008/18/26 and equivalent PoE versions have a Mode

push button that toggles between Managed and Unmanaged Modes. The

MGMT LED is on when the switch is in Managed Mode and is off when in

Unmanaged Mode. To configure the switch while in Managed Mode, see the

following sections.

NOTE: Release notes and user documentation can be downloaded from

dell.com/support.

Connecting the Switch to the Network

CAUTION: Do not plug a phone jack connector into an RJ-45 port. This will

damage the Ethernet switch. Use only twisted-pair cables with RJ-45 connectors

that conform to FCC standards.

To connect the switch to the network:

• Attach one end of a twisted-pair cable to the switch's RJ-45 connector and

the other end of a twisted-pair cable to another switch or server.

As each connection is made, the link LED corresponding to each port on the

switch is illuminated (green or amber) indicating that the connection is valid.

8Getting Started Guide

Initial Configuration Through the Web

The administrator can perform switch configuration using the web

management GUI.

To configure the switch, perform the following:

Verify that the switch is in Managed Mode.

Connect the switch to a PC using Ethernet, and set a static IP address of

192.168.2.x

(where x is between 2 and 254) and subnet mask of

255.255.255.0

on the PC. Note that the switch acts as a DHCP client and

can receive its IP address from a DHCP server. If using DHCP for IP

assignment, look up the assigned IP address and use it for the next step.

Connect to the switch using the default switch IP address

192.168.2.1

your web browser. The login username is

admin

with password

admin

After logging into the switch using the previous step, a getting started

wizard is available to guide the user through the initial switch

configuration. Applied changes are automatically saved to the startup

configuration.

CLI Access

To access the switch using the Command Line Interface (CLI), it must be in

Managed Mode. The Command Line Interface can only be reached by using

telnet or a console connection. See the user guide for limited CLI options.

NOTE: The default switch setting is Unmanaged Mode. To set the switch to

Managed Mode, press the Mode button for at least seven seconds.

Connecting the Switch to a Terminal Server/PC

NOTE: The console port enables connecting to a terminal or desktop system

running terminal emulation software for monitoring or debugging the device using

the micro-USB port. (You can find the USB drivers at dell.com/support.)

To use the console port, the following is required (e.g., PuTTY, TeraTerm, etc.)

• VT100 compatible terminal or a desktop or portable system with a USB

port and running VT100 terminal emulation software.

Otros manuales para X1000 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cambiar de Dell

Dell

Dell Powerconnect W-ClearPass Hardware Appliances Manual

Dell

Dell PowerConnect 6224 Manual de usuario

Dell

Dell PowerConnect 8024 Manual de usuario

Dell

Dell N2128PX-ON Manual de usuario

Dell

Dell PowerConnect 2708 Manual de usuario

Dell

Dell S4048-ON Manual de usuario

Dell

Dell S6100 Manual de usuario

Dell

Dell MXG610s Manual de usuario

Dell

Dell PowerConnect 3324 Manual de usuario

Dell

Dell PowerConnect 28 SERIES Manual de usuario

Dell

Dell Networking 7048 Manual de instrucciones

Dell

Dell PowerConnect M6348 Manual de instrucciones

Dell

Dell S4820T Manual de usuario

Dell

Dell PowerVault 56F Manual de usuario

Dell

Dell Networking S4810 Manual de instrucciones

Dell

Dell Networking 7048 Manual de usuario

Dell

Dell PowerConnect 3424 Cómo utilizar

Dell

Dell PowerConnect 8100 Series Manual de usuario

Dell

Dell Networking N2024 Manual de usuario

Dell

Dell PowerEdge 1855 Manual de usuario

Dell

Dell Networking S55 Manual de usuario

Dell

Dell PowerVault 50F Manual de usuario

Dell

Dell Networking S4810 Manual de usuario

Dell

Dell POWERCONNECT J SERIES Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario