Dell PowerApp .cache 100 Manual técnico

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Servidor de Dell

Dell

Dell DL4300 Manual de usuario

Dell

Dell S5000 Series Manual de usuario

Dell

Dell PowerEdge 2300 Manual de usuario

Dell

Dell PowerEdge T110 Manual de usuario

Dell

Dell PowerEdge R510 Manual de usuario

Dell

Dell Force10 MXL Blade Manual de usuario

Dell

Dell PowerEdge M630 Manual de usuario

Dell

Dell PowerEdge 1650 Manual técnico

Dell

Dell PowerEdge E31S Series Manual de usuario

Dell

Dell EMC ScaleIO Ready Node 14G Instrucciones de instalación

Dell

Dell PowerEdge 4600 Manual de usuario

Dell

Dell Poweredge metered Manual de usuario

Dell

Dell PowerEdge T710 Manual técnico

Dell

Dell PowerEdge E02B Manual de usuario

Dell

Dell PowerEdge 6850 Guía del usuario

Dell

Dell Force10 S25-01-GE-24P Manual de usuario

Dell

Dell PowerEdge systems 6300 Manual de usuario

Dell

Dell poweredge VRTX Manual de usuario

Dell

Dell PowerEdge R450 Manual de usuario

Dell

Dell DR6300 Manual de usuario

Dell

Dell PowerEdge C6220 II Manual de usuario

Dell

Dell EMC PowerEdge R940 Manual

Dell

Dell PowerEdge C6320 Manual de usuario

Dell

Dell PowerEdge 2450 Guía

Manuales populares de Servidor de otras marcas

HP

HP AlphaServer ES47 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Asus

Asus RS700DA-E6 PS4 Manual de usuario















This document updates information contained in your Dell PowerApp 100 appliance

documentation.

If you replace the appliance’s microprocessor and heat sink assembly, you must remove the fan

attached to the top of the replacement microprocessor and heat sink assembly. (For details on

removing the microprocessor, see “Microprocessor” in your Service Manual.)

To install the replacement microprocessor and heat sink assembly, perform the following steps:

1. If applicable, remove the fan from the heat sink in the replacement kit.

The fan will not be used. To remove the fan, gently squeeze the sides of two adjacent cor-

ners on the fan.

2. Gently place the replacement microprocessor into the zero insertion force (ZIF) socket so

that the processor pins mate exactly with the ZIF socket.

Make sure that pin 1 of the microprocessor is oriented correctly in the socket.





3. Swing the ZIF socket arm down until it snaps into the socket tab after the microprocessor is

in place.

4. At the base of the heat sink, remove and discard the protective cover over the thermal

grease by pulling the cover’s tab.

5. Place the heat sink on the microprocessor.

Be careful not to touch the surfaces coated with thermal grease.

The bevelled surface on the heat sink covers the part of the ZIF socket that is not covered by

the microprocessor.

6. Drop the heat sink clip into the heat sink's center groove with the end of the clip that has

two slots facing the front of the ZIF socket.

7. Gently hold the heat sink in place as you press down on the shorter end of the heat sink

clip (the end that has a single slot) until that end snaps into its tab on the back of the ZIF

socket (see Figure 1).



8. Use your thumb to press down on the front end of the heat sink clip (the end that has

two slots) until it snaps into the socket tab.

9. Replace the cover, install the power cord, and reboot the computer.

____________________

Information in this document is subject to change without notice.

© 2000 Dell Computer Corporation. All rights reserved. Printed in the U.S.A.

Trademarks used in this text: Dell, the DELL E COM logo, and PowerApp are trademarks of Dell Computer Corporation. Other

trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

heat sink clip

microprocessor and

heat sink assembly

tabs on ZIF socket (2)

ZIF socket

ZIF socket

release lever