Dell Poweredge metered Manual de usuario

Cable Routing Procedures for

Dell™ PowerEdge™ T610 Systems

A Dell™Technical White Paper

Dell™│Datacenter Infrastructure Engineering

By Chris Kitten and Jose L. Flores

March 2011

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page ii

THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL

ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS

OR IMPLIED WARRANTIES OF ANY KIND.

the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.

Dell

, the

DELL

logo, the

DELL

badge, and

PowerEdge

are trademarks of Dell Inc.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 1

Contents

Introduction...............................................................................................................................................................2

Section 1: Cabling a Dell™ PowerEdge™ T610 With a Cable Management Arm (CMA) ............................................2

1.1 Connecting the CMA Cables to the System..................................................................................................2

1.2 Routing the Power Cables Through the Strain Reliefs .................................................................................3

1.3 Installation of the CMA ................................................................................................................................3

Section 2: Cabling a Dell™ PowerEdge™ T610 System Without a CMA.....................................................................5

2.1 Routing the Cables .......................................................................................................................................5

Section 3: Replacing a Power Supply on a PowerEdge™ T610 System With a CMA..................................................6

Table of Figures

Figure 1: System with Cables Installed .................................................................................................................. 2

Figure 2: Routing Power Cables Through the Strain Reliefs ............................................................................. 3

Figure 3: Routing the Cables Through the CMA ................................................................................................. 4

Figure 4: Right-Side Mounted CMA Installation .................................................................................................. 4

Figure 5: Left-Side Mounted CMA Installation..................................................................................................... 5

Figure 6: Cable Routing Without a CMA............................................................................................................... 5

Figure 7: Replacing the Power Supply................................................................................................................... 6

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 2

Introduction

This white paper covers recommended cable routing procedures for Dell™ PowerEdge™ T610

systems in the following racks:

PowerEdge™ 2410

PowerEdge™ 4210

PowerEdge™ 2420

PowerEdge™ 4220 (including wide and deep versions)

PowerEdge™ 4820 (including wide and deep versions)

If you are using the optional CMA, following these procedures will allow you to extend the system

from the rack for service without powering down or disconnecting the cables. If you are not using the

CMA, following these procedures will ensure secure attachment and strain relief of the cables behind

the system. For guidelines on how to route cables within the rack, refer to the Dell

Best Practices

Guide for Rack Enclosures

white paper.

Section 1: Cabling a Dell™ PowerEdge™ T610 With a Cable Management

Arm (CMA)

This section details how to cable a PowerEdge™ T610 system using a CMA. If you are cabling the

system without the optional CMA, refer to Section 2.

Follow the instructions contained in the

Rack Installation Guide

in the rail kit to install the server into

the rack. Once installed, use these instructions to install the cables. All illustrations in the following

sections were created using a PowerEdge™ T610 system.

NOTE: PowerEdge™ T610 systems are compatible with the PowerEdge™ T710 rails and CMAs.

1.1

Connecting the CMA Cables to the System

Attach the CMA tray to the back of the rails as described in the

CMA Installation Instructions

provided

in the CMA kit. Connect all applicable cables to the rear of the system and verify that all connections

are secure. See Figure 1.

Figure 1: System with Cables Installed

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 3

1.2

Routing the Power Cables Through the Strain Reliefs

After you have installed the tray and cables, route the power cables through the strain reliefs located

on the power supply handles as shown in Figure 2.

Figure 2: Routing Power Cables Through the Strain Reliefs

1.3

Installation of the CMA

The CMA can be installed on either the rear right or rear left side of the rails. Mounting the CMA on the

side that is opposite of the power supplies (right-side mount) is recommended; otherwise, the CMA

must be partially disconnected in order to remove the lower power supply. Refer to Section 3 for

details on power supply replacement.

NOTE: For guidelines on how to route cables within the rack, refer to the Dell

Best Practices Guide for

Rack Enclosures

white paper

NOTE: If you are installing fiber-optic cables in the CMA, a cable bend radius of at least 1 inch must be

maintained throughout the length of the cable

It is recommended that fiber-optic cables be routed

on the exterior of the cable bundle to increase the bend radius of the fiber-optic cables through the

CMA. Additionally, a large amount of slack at the entrance and exit of the CMA is recommended.

1. Install the CMA on either the rear right or rear left side of the rails by attaching both CMA housings

to the attachment brackets on the rails.

2. Route the cables through the CMA while avoiding twisting the cables. Use the hook and loop

straps on the CMA to secure the cables. See Figure 3.

3. If the cable bundle includes a keyboard, video, and mouse (KVM) dongle, place the dongle inside

the CMA basket.

4. Once you have routed all the cables through the CMA, dress the cable slack between the back of

the system and the entrance of the CMA using the tie wraps (shown in yellow in all illustrations)

provided in the CMA kit.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 4

5. Clip off the excess length of material from the tie wraps. Make sure that the heads of the tie wraps

are positioned so as to avoid interference with adjacent systems. Return the CMA to the closed

(retracted) position.

6. Extend the system out of the rack to verify that there is sufficient slack in the cables on both ends

of the CMA.

See Figure 4 for an example of a completed right-side mounted CMA installation.

See Figure 5 for an example of a completed left-side mounted CMA installation.

Figure 3: Routing the Cables Through the CMA

Figure 4: Right-Side Mounted CMA Installation (Preferred)

Cables entering the CMA should have

a small amount of slack to avoid cable

strain when the CMA is extended.

NOTE: Do not store excess cable

slack inside the CMA. The cable may

protrude through the CMA, thus

causing binding and potentially

damaging the cable.

KVM dongle placed inside the basket.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 5

Figure 5: Left-Side Mounted CMA Installation

Section 2: Cabling a Dell™ PowerEdge™ T610 System Without a CMA

NOTE: The CMA on Dell™ PowerEdge™ T610 systems is optional. Without the CMA installed, the

system must be powered down and all cables disconnected before it can be removed from the rack.

2.1

Routing the Cables

1. Connect all applicable cables to the rear of the system and verify that all connections are secure.

2. Using the hook and loop straps supplied with the rail kit, bundle the cables and secure them to

either the left or right CMA attachment brackets as described in the

Rack Installation Instructions

See Figure 6 for an example of data cables secured to the left CMA bracket and power cables

secured to the right CMA bracket.

3. It is recommended that the cables be secured to the outer brackets, but cables may be secured to

the inner brackets as well if desired.

Figure 6: Cable Routing Without a CMA

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 6

Section 3: Replacing a Power Supply on a PowerEdge™ T610 System With a

CMA

NOTE: The steps described below apply to the bottom power supply only when the CMA is installed

to the left side. If the CMA is attached to the right side, both power supplies can be removed without

removal of the CMA. If the CMA is attached to the left side, the top power supply can be replaced with

the CMA in its closed (retracted) position.

1. Swing the CMA to its service position.

2. Disengage the strain relief and disconnect the power cord from the power supply.

3. Disconnect the inner CMA attachment housing from the rail as shown in Figure 8.

4. While supporting the CMA with one hand, remove and replace the power supply with the

other hand as shown in Figure 8.

5. Reconnect the CMA attachment housing to the rail.

6. Plug in the power cord, re-engage the strain relief, and return the CMA to the closed

(retracted) position.

Figure 7: Replacing the Power Supply

Inner CMA attachment housing

has been disconnected.

Otros manuales para Poweredge metered

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Dell

Dell

Dell PowerEdge T350 57C92 Manual

Dell

Dell PowerEdge R200 Manual de usuario

Dell

Dell PowerEdge 1300 Manual de instalación y operación

Dell

Dell Dimension 2200 Manual de lista de piezas

Dell

Dell PowerEdge systems 6300 Manual de usuario

Dell

Dell PowerEdge 2800 Manual

Dell

Dell PowerEdge 6600 Guía

Dell

Dell PowerEdge M1000e Manual de usuario

Dell

Dell PowerEdge T410 Manual de usuario

Dell

Dell POWEREDGE 1900 Manual técnico

Dell

Dell PowerEdge T410 Manual de usuario

Dell

Dell poweredge VRTX Manual de usuario

Dell

Dell EMC PowerEdge R240 CHRH4 Manual

Dell

Dell PowerEdge C6220 II Manual de usuario

Dell

Dell OptiPlex 9020 Manual de usuario

Dell

Dell POWEREDGE R515 Guía de inicio rápido

Dell

Dell PowerEdge 1600SC Manual de usuario

Dell

Dell PowerEdge C1100 Guía rápida

Dell

Dell PowerEdge C2100 Manual de usuario

Dell

Dell PowerEdge 2800 Manual de usuario

Dell

Dell Wyse 5040 AIO Manual de usuario

Dell

Dell PowerEdge T420 Manual de usuario

Dell

Dell PowerEdge C6100 Manual de usuario

Dell

Dell PowerEdge 1855 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Asus

Asus RS700DA-E6 PS4 Manual de usuario